I found a bunch of gold! I'm rich!

Well, now what

  • Change the oil, run it a few more miles, check again

    Votes: 32 78.0%
  • Pull it apart.

    Votes: 9 22.0%

  • Total voters
    41
It is composite gear 100%

I have no idea what is bronze in an engine. I'm not a builder and have minimal experience with anything engine related. I don't know shit about fuck when it comes to that.

I swirled the magnet around and I do have some ferrous metal as well.

the metal on the magnet could be from not cleaning the block 100% after the machining process. Like others have said , maybe put some fresh oil (buy something cheap and you can run it a qt low just idling) in it and run it again for a few minutes while keeping an eye on the oil pressure then cut open the filter and see what you got . If there is an issue another minute or 2 run time is not going to cause anymore damage than has already been done .
Make sure you clean your drain pan thoroughly before draining the new engine oil into it .
 
Last edited:
I think all you're seeing is a fresh engine oil change,
Every engine I've built, I typically run the engine the first time for 10-15 minutes getting oil up to temp and drain and refill with a new filter.
Change it and take it for an easy 5 mile cruise watching temp and oil pressure.

Is it possible that you have bronze lifter bores?
 
I think all you're seeing is a fresh engine oil change,
Every engine I've built, I typically run the engine the first time for 10-15 minutes getting oil up to temp and drain and refill with a new filter.
Change it and take it for an easy 5 mile cruise watching temp and oil pressure.

Is it possible that you have bronze lifter bores?

For lifter bores I don't believe that's the case. Stock block out of 1984 ish truck.

@SRGN Many moons ago on DRP you said if the block was line honed it would fuck with something, would that have anything to do with this?
 
I'm for fresh oil and another run. Hard to figure where that much copper came from with so little run time.

Just an FYI, I don't like to run a neutral safety switch with a stout clutch. Don't like pushing the crank forward during cranking with no oil pressure to the thrust bearing.
 
No luck, it's a composite gear
If there's one thing in the world of aftermarket parts that I absolutely hate its composite distributor gears. Those things are absolute crap. I got stranded on a mountain pass in far NW Colorado (got towed to bum fuck Wyoming) by a shredded de-toothed comp dist gear, friends had similar experiences. What a farce, the crap is NOT strong, get rid if it and NEVER look back. JMHO
 
If there's one thing in the world of aftermarket parts that I absolutely hate its composite distributor gears. Those things are absolute crap. I got stranded on a mountain pass in far NW Colorado (got towed to bum fuck Wyoming) by a shredded de-toothed comp dist gear, friends had similar experiences. What a farce, the crap is NOT strong, get rid if it and NEVER look back. JMHO

6 out of 7 ford builders disagree and suggest the composite, so that's what I'm using
 
That's a lot of shit for such limited run time.
Makes me wonder if they cleaned the block after machining.

I don't want to make any assumptions, but the block should have been cleaned twice. The place I bought the block from does all machining and installs cam bearings. When I received it, it was cleaned painted and lubricated.

I took it to the builder about a year later and he knew the situation, assuming he'd have cleaned it also
 
Whole nother thread, but those composite gears are shit, and it's only a matter of time before it leaves you stranded. Ford builders need to get out more.

@itey can you explain more than I can here

Oct 8, 2023 #584
The composite gears are not so bad as people think.

Several years ago went a few rounds with a 351W in a fine '69 Mustang, CC hyd roller, don't know about the oil pump, but it ate three bronze gears, all from CC. The 2nd and 3rd were showing rapid wear in just a few miles so were changed immediately. The 4th gear is a composite from CC and it has been in use continually since in the sunny day daily driver / track day toy.

I guarantee the gears were all installed correctly to the depth and shaft end clearance required in FoMoCo specs and the block dimension was double checked.

Because of the circus with the bronze gears we pulled the plastic gear several times in a few miles, few days, few months, and the next two annual oil changes, and not a bit of wear, it literally didn't look like it had been run at all.

.........

but it's a lot easier to repeat internet shitalk than what you don't know first hand
 
Oct 8, 2023 #584
The composite gears are not so bad as people think.

Several years ago went a few rounds with a 351W in a fine '69 Mustang, CC hyd roller, don't know about the oil pump, but it ate three bronze gears, all from CC. The 2nd and 3rd were showing rapid wear in just a few miles so were changed immediately. The 4th gear is a composite from CC and it has been in use continually since in the sunny day daily driver / track day toy.

I guarantee the gears were all installed correctly to the depth and shaft end clearance required in FoMoCo specs and the block dimension was double checked.

Because of the circus with the bronze gears we pulled the plastic gear several times in a few miles, few days, few months, and the next two annual oil changes, and not a bit of wear, it literally didn't look like it had been run at all.

.........

but it's a lot easier to repeat internet shitalk than what you don't know first hand
I've lost track of how many of those pieces of shit I've seen fail on Chevy applications, including my own car. If you're lucky enough to get the one person left at Comp that knows anything, they don't recommend them for wet sump applications. I am happy they have worked out for you though.
 
I've lost track of how many of those pieces of shit I've seen fail on Chevy applications, including my own car. If you're lucky enough to get the one person left at Comp that knows anything, they don't recommend them for wet sump applications. I am happy they have worked out for you though.
Maybe the plastic Ford gear is made in USA.

I confess I was skeptical of the plastic gear, but three bronze gear fails was a sign to try something else. If the plastic didn't work plan C was to get a stock FoMoCo steel gear for the factory roller cam in 302 and 351 HO motors.
 
For lifter bores I don't believe that's the case. Stock block out of 1984 ish truck.

@SRGN Many moons ago on DRP you said if the block was line honed it would fuck with something, would that have anything to do with this?
Timing chain length changes from a line hone, since the crank is higher up in the block. Not likely to have any effect on what you are seeing. Fresh oil and filter, run it again, and see if it's still creating more gold flakes. Another thought... Did you have brass freeze plugs installed? If the rear cam plug is brass and installed too deep, it could be the issue. Pull the distributor, see if you can move the cam forward and backward at all. Should have a little bit of play, but it's only a few thousandths.
 
I have not seen a composite gear last a single race season, but who knows.
I have eaten bronze gears in less than 20k miles, that's ok with me, cost of doing business.
 
For fuck sakes fill the cocksucker with oil, spin a new filter on it, run it and see what happens. The damage is fucking done already if it's something major. You could have figured all this out in 30 minutes yesterday.
 
For fuck sakes fill the cocksucker with oil, spin a new filter on it, run it and see what happens. The damage is fucking done already if it's something major. You could have figured all this out in 30 minutes yesterday.

Not true you mean fuck! The oil won't get here until Thursday because God forbid I buy ots oil from vato zone.

Setting lash and putting new filter on tonight. I'll fill and run anther 10 miles and investigate again once the oil arrives.

Comp break in oil from summit on the way, same as I used first time
 
We don't run composite gear on engines with internal oil pumps. The SBF love to destroy thrust bearings, we run two dumps on the trans to keep line pressure low while building boost. On last tear down we noticed some gold color in the clear view filter, we had no thrust movement and no bearing wear. still don't know where it came from.
 
Back
Top