I found a bunch of gold! I'm rich!

Well, now what

  • Change the oil, run it a few more miles, check again

    Votes: 32 78.0%
  • Pull it apart.

    Votes: 9 22.0%

  • Total voters
    41
@Boosted Bullet how do I check the thrust? All I'm finding is shit while the engine is disassembled. I only have 3/4 inch clearance between fans and balancer so I'd likely have to pull all that shit off to check it
 
@Boosted Bullet how do I check the thrust? All I'm finding is shit while the engine is disassembled. I only have 3/4 inch clearance between fans and balancer so I'd likely have to pull all that shit off to check it
That's what I was thinking, sbf are notorious for thrust issues. Maybe your clutch setup might be pushing crank forward or not far enough Out of pump if automatic
 
Doubt it helps any, but just about every one of us has been in your situation before. Having to take something all back apart when there "SHOULDN'T" have been anything wrong. And sometimes more than once, twice, or even more!
 
So yeah - it's something catastrophic, not wear.
I wonder if one of the valves is fucked up and scraping the guide.
If you could get your hands on one of those "on the head" valve spring pressure testers you could see if one of the valves is hard to press.
 
Have you pulled the distributor and looked at the gear yet?

Negative, since it was so few miles and a composite gear I wasn't sure what kind of useful info I could attain by doing so. Do you recommend I check to see if it's getting chewed up? Or what should I look for

Like somebody asked previously, are you absolutely sure it is not a bronze gear?

What sources of bronze are in your engine? .... other than cam drive thrust washer or distributor gear or crankshaft end thrust flange? What else can it be?

Did you look for iron or steel with a magnet?
 
Like somebody asked previously, are you absolutely sure it is not a bronze gear?

What sources of bronze are in your engine? .... other than cam drive thrust washer or distributor gear or crankshaft end thrust flange? What else can it be?

Did you look for iron or steel with a magnet?

It is composite gear 100%

I have no idea what is bronze in an engine. I'm not a builder and have minimal experience with anything engine related. I don't know shit about fuck when it comes to that.

I swirled the magnet around and I do have some ferrous metal as well.

 
@Boosted Bullet how do I check the thrust? All I'm finding is shit while the engine is disassembled. I only have 3/4 inch clearance between fans and balancer so I'd likely have to pull all that shit off to check it

Didnt consider what might be in the way, but anyplace you can get an indicator on either end the crank, and be able to move it back and forth with a prybar or something. A lever type indicator may work better than a plunger type in a tight spot if you have one.
 
Run it with clean oil and check again. If you get more metal, I kinda suspect a spun or incorrectly installed cam bearing.
I had a guy call me and text me a bunch today with an issue just like this and I told them the same thing. I wonder if that guy listened?
 
It is composite gear 100%

I have no idea what is bronze in an engine. I'm not a builder and have minimal experience with anything engine related. I don't know shit about fuck when it comes to that.

I swirled the magnet around and I do have some ferrous metal as well.

That amount for iron is possibly normal.

I had an engine using NOS pistons and rings bored, and because they were not familiar with a chrome ring bore finish, they went overboard making it rough. IDK what they did but holy shit, the magnetic drain plug looked 50x worse than that, and yet the engine actually took me all over North America once broken in. Didn't burn a drop of oil. Slightly down on power, I felt, though.

Only advice I have is if it's the crank- it might not be, but if it is, spend the $ to have it repolished. People roll bearings in, and it becomes a matter of a few hundred hard hours and you are back at needing a repair.

I'd listen to SRGN, it is very likely cam bearings. H/Roller cams are either case hardened (yours, being a -8, I think), or steel. But between cam bearings not being given a precision check and the cams having runout, weird stuff happens.
I've seen it but do not know the correct way of going through it at a machine shop, to "blue print the tunnel" if necessary. I can speculate but speculation's not what you need. There are many here who *know*.
 
Well hell, thars gold in that thar oil, but that can't be good can it.:unsure:
 
Back
Top