Breaking up at high rpm, carb issues, and converter issues.

What’s your rear rim width & offset/ backspace? I have several sets of rims & tires you can borrow.
15x12 7.5" BS, I don't remember the offset. I suppose I could measure it later. Finding wheels that fit 5/8" studs is the hard part.
 
We have had 2000hp (RWP) on the chassis dyno. Most dynos stop acquiring data at 200 mph. But we can still get the data we need with the on board data acquisition. I only deal with EFI cars so everyone of them has it built-in.
Funny when the pull lasts 5 seconds.
Never popped a tire, never hurt a tire.
Have to watch trans temperatures if you make a lot of pulls, many people don't and wind up puking fluid out the vent tube.
I have set my car of fire from synthetic trans fluid getting on the headers, that shit goes up fast! We got it out quickly, no damage.

The place I used to go to all the time would let me and my buddy do it all.
Strap the car down, run the chassis dyno, he would go home at eat. He lived on the property.
 
15x12 7.5" BS, I don't remember the offset. I suppose I could measure it later. Finding wheels that fit 5/8" studs is the hard part.
If you weren't so far, the rear wheels on my Camaro would fit. 5x4.5 bolt pattern, 5/8 studs. 14x32 tires that would require surgery on your car, however.
 
Looks like you have a good hot rod there ole son. 😃
Thanks.

Today was just a day to mess with suspension. I purchased an upper control arm set up that has more holes to dial in the IC, but I have not had time to install it yet.

after the bar change, my 60’ dropped to a 1.309, but I ran a new PB for e.t. and mph.

5.810 @ 118.58
Not sure why it went faster, air was worse. Hoping to get the new uppers installed before the next time out.

Today’s 4 runs in order. No two suspension settings were the same.

 
well you learned the car wants more tail gear.. (shorter tire)
what change did you make when it went the best et? I know it lost 60, but must have been happier the rest of the time?
 
well you learned the car wants more tail gear.. (shorter tire)
what change did you make when it went the best et? I know it lost 60, but must have been happier the rest of the time?
I lowered the bottom bar 1 hole in front. In order to shorten the instant center my bottom bar angle is very drastic. At the axle it’s only 6.25” off the ground and the front is 8.375” off the ground.

Once I get the upper control arm brackets on, I will be able to level the lower bar (probably up slightly in front) and dial in my IC with the uppers.

Right now I’m stuck with the stock upper control arm mounting point. I’m hoping to install the new stuff this week.
 
I lowered the bottom bar 1 hole in front. In order to shorten the instant center my bottom bar angle is very drastic. At the axle it’s only 6.25” off the ground and the front is 8.375” off the ground.

Once I get the upper control arm brackets on, I will be able to level the lower bar (probably up slightly in front) and dial in my IC with the uppers.

Right now I’m stuck with the stock upper control arm mounting point. I’m hoping to install the new stuff this week.
until then, you can move the ic up some with rideheight.
My roadster had 1 useable set of holes, and i controlled it with ride height changes
 
until then, you can move the ic up some with rideheight.
My roadster had 1 useable set of holes, and i controlled it with ride height changes
Yes, I have played with that as well. If I would have raised the shock brackets the IC would have lengthened the IC and raised it 3”. It also would have increased AS from 133% to 142%.
 
Yes, I have played with that as well. If I would have raised the shock brackets the IC would have lengthened the IC and raised it 3”. It also would have increased AS from 133% to 142%.
my roadster initially had the lower bar traveling down, and the ic pretty low. I had to raise it to keep it from just sitting on the rear tire
My gto obviously was much more adjustable. Up here with no air in the air (8500+ DA) i ended up taking it to like 70% AS to keep it from bouncing and let it get up on the tire. But i didnt like how that felt down track. It was skatey (is that a word? lol)
I needed to probably work harder on shock settings and leave it closer to 100%
but that car is gone now
 
I’m going to post these plug pics in here because the plug reading thread doesn’t get any looks.

Don’t beat me up about pulling a plug after a pass, I plan to do it next trip out.

Timing is set at 30* locked out. This first pic is an autolite AR3935. It was one aborted run and two full passes. A minimal amount of idle time.



These ugly fuckers are the NGK 7’s that I pulled out last week. They have about 14 passes on them. I have no idea WTF is going on, but as @Maggifinn stated in the other thread, the cylinders don’t look happy.

Why do they look rusty with a build up of shit on them?

 
I’m going to post these plug pics in here because the plug reading thread doesn’t get any looks.

Don’t beat me up about pulling a plug after a pass, I plan to do it next trip out.

Timing is set at 30* locked out. This first pic is an autolite AR3935. It was one aborted run and two full passes. A minimal amount of idle time.



These ugly fuckers are the NGK 7’s that I pulled out last week. They have about 14 passes on them. I have no idea WTF is going on, but as @Maggifinn stated in the other thread, the cylinders don’t look happy.

Why do they look rusty with a build up of shit on them?

Detonation?
 
Detail your entire process. “Like” =Do you start it & get it up to operating temperature prior to your burn out, then make your pass, then drive it back to the trailer & let the fans & water pump run until the motor is ambient? Rinse & repeat.
What is the motor temp prior to your burn out, beginning & end of run, & what is your procedure back at the trailer?
 
Call back, ask nkg if 5's are right for mine because i have 24 of them 🤣
 
-8's for 13:1 and up is my rule.
-9's and greater once you start with power adder stuff.

Warm up the engine before a pass like normal. Put two new plugs in it. Drive it to the lanes and make your pass. On the return road leave your fire gloves on, remove those two plugs, put in two old plugs and drive it back. Cut them open. You will see the fuel ring down inside, very hard to do without cutting them open. The fire gloves work great, better than Mechanix gloves by far.

Look inside your exhaust pipes, should be light gray. If your A/F meter is working correctly, you should be running 13.0 to 13.3 A/F going down the track. The ring on the porcelain should be thin and light gray. Thick and brown is too rich, but the A/F gauge should have shown that anyway.

It's an N/A engine, hard to hurt at your horsepower and compression with a bad tune. Too much timing can do more damage than too much or too little fuel. The high compression high power N/A stuff with .8mm and thinner rings are another story.........
 
Back
Top