Breaking up at high rpm, carb issues, and converter issues.

So post #346 shows you shutting down around 7250rpm maybe? Was that right at the 1/8th mile?

How far have you run under power to? 1000? Distance and RPM?
Do you run bias ply slicks or radials?

Lots of variables to consider, such as, but not limited to.......do we know where your peak torque and HP are? How hard is it to put a slightly taller tire under the car? How often do you plan on running 1/4 mile?

At your general power level/ET, there should not be a big difference in 1/8 mile and 1/4 mile rpm. I know you want to preserve your engine and not over rev it, but any decent small block like yours should laugh at 7500-7600rpm unless your valve train is exceedingly weak. At 7250 through the 1/8th, you are not going to see past 7600rpm to the quarter unless your convertor decides to slip like crazy.

FWIW......we all see stuff that is not typical from time to time, but it has been my experience that unless you have a high end full tube chassis car with all the good chassis parts to go with it, slowing down the tire at the hit with numerically higher gears will NOT help your ET to the 1/8th, and putting numerically lower gears in the rear end to "tame down" the initial hit will slow you short numbers(60') very little if any at all.

It has been my experience that rear gear changes only make a big difference if you have a Bickel/Haas/or other big name chassis and you are chasing every .00X you can get.

From the limited video's, it looks to me like your car just needs a bit of shock and tire management. If you have a slick tire out back, maybe even a set of wheelie bars to help control the smash initially.
 
So post #346 shows you shutting down around 7250rpm maybe? Was that right at the 1/8th mile?

How far have you run under power to? 1000? Distance and RPM?
Do you run bias ply slicks or radials?

Lots of variables to consider, such as, but not limited to.......do we know where your peak torque and HP are? How hard is it to put a slightly taller tire under the car? How often do you plan on running 1/4 mile?

At your general power level/ET, there should not be a big difference in 1/8 mile and 1/4 mile rpm. I know you want to preserve your engine and not over rev it, but any decent small block like yours should laugh at 7500-7600rpm unless your valve train is exceedingly weak. At 7250 through the 1/8th, you are not going to see past 7600rpm to the quarter unless your convertor decides to slip like crazy.

FWIW......we all see stuff that is not typical from time to time, but it has been my experience that unless you have a high end full tube chassis car with all the good chassis parts to go with it, slowing down the tire at the hit with numerically higher gears will NOT help your ET to the 1/8th, and putting numerically lower gears in the rear end to "tame down" the initial hit will slow you short numbers(60') very little if any at all.

It has been my experience that rear gear changes only make a big difference if you have a Bickel/Haas/or other big name chassis and you are chasing every .00X you can get.

From the limited video's, it looks to me like your car just needs a bit of shock and tire management. If you have a slick tire out back, maybe even a set of wheelie bars to help control the smash initially.
Post #346, my fastest pass to date I stayed in it to see if I could make it to the end of the 1/4. I took my foot out of it when the shift light came on. If I had to guess, I was 3/4 of the way there.

I don’t know about the distance and rpm. I’m pretty sure I was under power to 1000 on that time slip. I’m using a 29x12.5-15 bias ply slick.

I do not know peak horse power and tq. I never had the engine dynoed after the shit show I went through getting it built. Would it be worth putting it on a dyno to get some numbers?

I don’t think I could go taller than a 29.5 without stretching the quarters.

It seems most of the racing here focuses on 1/8th mile.

I’m planning to focus a bit more on suspension next time out.
 
Stick it on a chassis dyno one day, far cheaper than an engine dyno and way easier to do!
My car will run 9.4's @ 8200 rpm in the 1/4 with a 29 x 10 bias ply slick.
I use a 29.5 x 10.5 now which is actually just about a 31" tall tire, but the rpm was closer to 7800 now going 9.5's.

I know Fox Body guys can run a 28 x 10 slick no problem, but a 29 like you are running is about it without working the wheel well. I had to do a little work on mine on my 3rd Gen F Body for the 29.5.
 
Stick it on a chassis dyno one day, far cheaper than an engine dyno and way easier to do!
My car will run 9.4's @ 8200 rpm in the 1/4 with a 29 x 10 bias ply slick.
I use a 29.5 x 10.5 now which is actually just about a 31" tall tire, but the rpm was closer to 7800 now going 9.5's.

I know Fox Body guys can run a 28 x 10 slick no problem, but a 29 like you are running is about it without working the wheel well. I had to do a little work on mine on my 3rd Gen F Body for the 29.5.
I just got off the phone with a guy at a dyno shop near me. I'm going to take it there possible next week. Told me to call back on Monday because they will be out this weekend racing in Ohio. If not next Friday, I'll get it there soon.
 
take out .008-.010
probably need more but a good starting point
and at some point id throw the power valve as far away as you can get it and square jet...lol
its a variable
the math is
afr you have / afr you want
so
11.5/12.5
a carb doest work quite as well as efi, but that gets you in the neighborhood
If blocking the PV and squaring the jets, do I just match the fronts to what's in the back? So right now, the secondaries have BLP .110's in them. Block power valve and put .110's in front?
 
If blocking the PV and squaring the jets, do I just match the fronts to what's in the back? So right now, the secondaries have BLP .110's in them. Block power valve and put .110's in front?
yes, that would be my thoughts
id call blp to make sure
but thats what i would do on the dyno, but i have 8 o2 to tune with...lol
ive just never been a fan in a drag race setup of a powervalve
 
yes, that would be my thoughts
id call blp to make sure
but thats what i would do on the dyno, but i have 8 o2 to tune with...lol
ive just never been a fan in a drag race setup of a powervalve
Sounds like Mark @ BLP is a fan of the PV. I remember him saying that it keeps the plugs clean since I still drive the car in the pits and return road, but I'll ask him.
 
Sounds like Mark @ BLP is a fan of the PV. I remember him saying that it keeps the plugs clean since I still drive the car in the pits and return road, but I'll ask him.
if a person knows what they are doing, you can keep them reasonably clean without one too.
I get it, the concept of it. Idle and part throttle it should help it not get slobbery.
 
I just got off the phone with a guy at a dyno shop near me. I'm going to take it there possible next week. Told me to call back on Monday because they will be out this weekend racing in Ohio. If not next Friday, I'll get it there soon.
dont hold me to this. From what I understand running slicks on a dyno will ruin them. Now if you are using the type of dyno that hooks up to the axle disregard my post.
 
dont hold me to this. From what I understand running slicks on a dyno will ruin them. Now if you are using the type of dyno that hooks up to the axle disregard my post.
I specifically asked him about that and he said "it's fine, I do it on my own car all the time." I would use another set of wheels, but it's hard to find anything since I have 5/8" studs.
 
I specifically asked him about that and he said "it's fine, I do it on my own car all the time." I would use another set of wheels, but it's hard to find anything since I have 5/8" studs.
Fair enough . I guess I heard wrong or misunderstood.
On a side note, this thread is full of good info. (except for my dyno post :) )
 
Fair enough . I guess I heard wrong or misunderstood.
No I doubt you heard wrong or misunderstood. I'm still concerned about it, but what are my options if I can't find wheels/tires? I mean a few pulls is going to kill them? Maybe somebody here that has or had a dyno will chime in?
 
No I doubt you heard wrong or misunderstood. I'm still concerned about it, but what are my options if I can't find wheels/tires? I mean a few pulls is going to kill them? Maybe somebody here that has or had a dyno will chime in?
I dont think you have any choice. Like you said a few pulls what can it really hurt if there is an issue with slicks and dyno pulls. I am sure the guy knows what he is talking about.
 
No I doubt you heard wrong or misunderstood. I'm still concerned about it, but what are my options if I can't find wheels/tires? I mean a few pulls is going to kill them? Maybe somebody here that has or had a dyno will chime in?

Never ran on a chassis dyno myself, but I have watched several cars run on them. This is just my guess, but I would not be overly worried about running a car at your HP level with slicks the size of yours. I would not run my car with huge rollers out back and more power on one though.
 
No I doubt you heard wrong or misunderstood. I'm still concerned about it, but what are my options if I can't find wheels/tires? I mean a few pulls is going to kill them? Maybe somebody here that has or had a dyno will chime in?
No problem, been doing it since the early 90's. Sometimes the DOT Drag Radials chunk, but we NEVER had an issue with a slick, bias or radial type.
Only issue I had was when I hit it with 300hp more and spun the dyno to 160. Tires grew more than I expected!
But they made another 200 passes after that.
Put 20 psi in them and you will be fine.
 
If a tire will hook on the street it will hook on most chassis dynos. Some power monsters that are sketchy to hook on a prepped track will lose a lot of rubber in a short time on a dyno.

The dyno should have a photocell deal that measures tire slip. If there is tire slip the numbers are worthless for power but you might get some A/F info that you already have from the O2 in the car.

If there is tire slip the HP curve will be sawtooth because the tire will slip and grab & slip and grab.

The acceleration app in a smart phone will tell you the HP accurately if you know the weight of the car, plus you can dial in jetting and ignition timing by which adjustment gives the best acceleration g force.
 
Last edited:
Back
Top