Breaking up at high rpm, carb issues, and converter issues.

If a tire will hook on the street it will hook on most chassis dynos. Some power monsters that are sketchy to hook on a prepped track will lose a lot of rubber in a short time on a dyno.

The dyno should have a photocell deal that measures tire slip. If there is tire slip the numbers are worthless for power but you might get some A/F info that you already have from the O2 in the car.

If there is tire slip the HP curve will be sawtooth because the tire will slip and grab & slip and grab.

The acceleration app in a smart phone will tell you the HP accurately if you know the weight of the car, plus you can dial in jetting by which jet size gives the best acceleration g force.
I would rather get this done on the dyno. I talked to the shop again and it's $200 an hour unlimited pulls. He told me to bring my timing light and jets. I'll be able to get a lot of data and dial it in, then fine tune at the track.
 
Never ran on a chassis dyno myself, but I have watched several cars run on them. This is just my guess, but I would not be overly worried about running a car at your HP level with slicks the size of yours. I would not run my car with huge rollers out back and more power on one though.
If a tire will hook on the street it will hook on most chassis dynos. Some power monsters that are sketchy to hook on a prepped track will lose a lot of rubber in a short time on a dyno.

The dyno should have a photocell deal that measures tire slip. If there is tire slip the numbers are worthless for power but you might get some A/F info that you already have from the O2 in the car.

If there is tire slip the HP curve will be sawtooth because the tire will slip and grab & slip and grab.

The acceleration app in a smart phone will tell you the HP accurately if you know the weight of the car, plus you can dial in jetting by which jet size gives the best acceleration g force.
so I guess I was not totally off base.
I thought I heard something about it but never paid much attention to the specifics such as low HP, high HP, big tire, small tire , light car , heavy car ,ect cause it was something that I would never be involved with.
 
Goneracin.......when you jet carbs on an engine dyno, do you take into consideration how much more air will be coming in at speed on the track?

Say we are dealing with an engine in the 1000hp range on the dyno, how much hp, if any, do you think it picks up on an actual run down track with roughly the same weather conditions as the dyno room run?
 
so I guess I was not totally off base.
I thought I heard something about it but never paid much attention to the specifics cause it was something that I would never be involved with.
I actually had this car on the dyno with slicks before, but it had about 350hp, so I didn't think it was worth mentioning. It probably has near double that now, but apparently I'm still good. :)
 
I actually had this car on the dyno with slicks before, but it had about 350hp, so I didn't think it was worth mentioning. It probably has near double that now, but apparently I'm still good. :)
I was just putting it out there. all is good
 
I was just putting it out there. all is good
you arent wrong. Some of the rollers are really aggressive and will assrape slicks.
Also, when the tire grows, its pulling it down pretty hard due to being strapped down
the guy in the same building as me has a chassis dyno, and weve run a few cars with radial slicks on it, but no big bias ply that grow more
 
Goneracin.......when you jet carbs on an engine dyno, do you take into consideration how much more air will be coming in at speed on the track?

Say we are dealing with an engine in the 1000hp range on the dyno, how much hp, if any, do you think it picks up on an actual run down track with roughly the same weather conditions as the dyno room run?
we throw a dart at a board...lol
actually, when it pressurizes the scoop, most of the added fuel it needs from the power is added via pressurizing the bowls.
G force is one thing i cant simulate though. Dumping the clutch tends to lean out 1&2, and fatten everything behind it up.
 
you arent wrong. Some of the rollers are really aggressive and will assrape slicks.
Also, when the tire grows, its pulling it down pretty hard due to being strapped down
the guy in the same building as me has a chassis dyno, and weve run a few cars with radial slicks on it, but no big bias ply that grow more
that makes sense that the car being strapped down will not let the slick grow and that would put a lot of pressure/abuse on the slicks especially if its a big tire cause it would want to grow more than a small tire.
Thanks for explaining
 
Last edited:
I actually had this car on the dyno with slicks before, but it had about 350hp, so I didn't think it was worth mentioning. It probably has near double that now, but apparently I'm still good. :)
My first thought was sidewalls. But some good info here. Glad your car is picking up.
 
I think I have ADD, couldn’t sit still last night, so I went out to the shop and removed the 29” tires and put the 28’s on.

I don’t know if that will negatively effect what the converter is doing. The 28’s are only 2lbs less ea. I also lowered the shocks one hole (1/2”). The smaller tires and lowering the shocks improves my suspension geometry a bit. I couldn’t make it to the end of the quarter with the 29’s, so no loss going to 28’s, but I will cross the 1/8 mi stripe at a higher rpm.

Curious to see how the car will respond. I still have to lower the front a little, check pinion angle, and set ARB.

 
Just talked to Coan. The converter is falling back roughly 1000 rpm after the shift. If they loosen the converter so that it flashes higher then the fallback rpm will also be higher.

He said they could loosen it a couple hundred rpm, but it’s extremely close. If I go to a lower numerical gear it might be right where it needs to be.

I’ll see what happens with the smaller tires and go from there.
 
What’s your rear rim width & offset/ backspace? I have several sets of rims & tires you can borrow.
 
Back
Top