Breaking up at high rpm, carb issues, and converter issues.

-8's for 13:1 and up is my rule.
-9's and greater once you start with power adder stuff.

Warm up the engine before a pass like normal. Put two new plugs in it. Drive it to the lanes and make your pass. On the return road leave your fire gloves on, remove those two plugs, put in two old plugs and drive it back. Cut them open. You will see the fuel ring down inside, very hard to do without cutting them open. The fire gloves work great, better than Mechanix gloves by far.

Look inside your exhaust pipes, should be light gray. If your A/F meter is working correctly, you should be running 13.0 to 13.3 A/F going down the track. The ring on the porcelain should be thin and light gray. Thick and brown is too rich, but the A/F gauge should have shown that anyway.

It's an N/A engine, hard to hurt at your horsepower and compression with a bad tune. Too much timing can do more damage than too much or too little fuel. The high compression high power N/A stuff with .8mm and thinner rings are another story.........
Mike, Thanks for always giving clear and easy to follow advice. I replaced the plugs with 8’s today and bought 8 extras. Planning to pull plugs after a pull this Friday. I bought a 5/8” hole saw to cut plugs at the track. Now, how high up is ideal for the fuel coloring?
 
Mike, Thanks for always giving clear and easy to follow advice. I replaced the plugs with 8’s today and bought 8 extras. Planning to pull plugs after a pull this Friday. I bought a 5/8” hole saw to cut plugs at the track. Now, how high up is ideal for the fuel coloring?
Right in the bottom
if its climbing the porcelain its too fat.
It needs a nice tan. To too two dark is to too two 2 fat
you can accomplish th same thing with a really good otoscope
search ebay. Dumbasses flunking out of med school need money, and sell the good ones for 30% of new
 
Right in the bottom
if its climbing the porcelain its too fat.
It needs a nice tan. To too two dark is to too two 2 fat
you can accomplish th same thing with a really good otoscope
search ebay. Dumbasses flunking out of med school need money, and sell the good ones for 30% of new
I’ve had an otoscope forever, never liked looking down at an angle like that. I’ll play with that tomorrow maybe I’ll figure it out, haven’t looked through it in about 12-13 years. I just figure cutting it gives a clear as day picture that I can post up as well.

Right at the bottom? If I had to measure it what would you say?
 
I’ve had an otoscope forever, never liked looking down at an angle like that. I’ll play with that tomorrow maybe I’ll figure it out, haven’t looked through it in about 12-13 years. I just figure cutting it gives a clear as day picture that I can post up as well.

Right at the bottom? If I had to measure it what would you say?
right in the radius at the bottom
like right where the porcelain meets the steel
if it comes up past the radius its fat
If i had to say a color, light milk chocolate brown,
Not even halle berry dark
more mariah carey
 
right in the radius at the bottom
like right where the porcelain meets the steel
if it comes up past the radius its fat
If i had to say a color, light milk chocolate brown,
Not even halle berry dark
more mariah carey
So again, don’t listen to this guy? 😁


 
holy fuck
idk what that is, but im sure it ran like fidos ass
if an na gas motor looks like that
dump her in the bay (Sausolito Summernight) reference
I’m a visual kind of guy, so according to dragstuff’s article, this plug is a mid 9 sec car and this plug is very close maybe a tad lean. So this is basically what I’m looking for? If this is a tad lean, how much different will perfect look? Or once it gets this close, watch mph?


 
if thats lean its not by much
his 3mph didnt come from 1 psi of fuel.
im assuming he means 1 psi in a nitrous system, because 1 psi at the carb as a rule isnt shit
 
if thats lean its not by much
his 3mph didnt come from 1 psi of fuel.
im assuming he means 1 psi in a nitrous system, because 1 psi at the carb as a rule isnt shit
I threw that comment out the window the moment I read it. Seemed like bullshit. Ok, I now have a visual of what I'm looking for.

So, I busted out my otoscope this morning and looked at all of the plugs that I posted (on the table). There is orange gunk in some of them that makes it look like these plugs were sitting out in the rain for 2 weeks. WTF is going on there? C12 is green, unless there is an additive in the fuel that turns red? I think some of the gunk is anti-seize. I cleaned the plug holes best I could and didn't put it on the new plugs.
 
I’m a visual kind of guy, so according to dragstuff’s article, this plug is a mid 9 sec car and this plug is very close maybe a tad lean. So this is basically what I’m looking for? If this is a tad lean, how much different will perfect look? Or once it gets this close, watch mph?


That is a nice fuel ring. Ain't no way that isn't a nitrous pass though as Bob states. As far as a nitrous plug, it's actually on the fat side, but that doesn't matter here.

If you have a generator bring a Dremel tool with you and use that to cut the plug apart. If you have a cordless drill AND a Dremel tool you can cut it in no time. Spin the plug one direction in the drill, the Dremel spinning the opposite direction, watch how fast you take it apart. Try it at home, thank me later!

And you only need to do this a few times. Once you see a good plug you'll know the A/F ratio you want to keep them that way. It's a low compression N/A engine, there is a large window to run in that won't affect ET/MPH or damage anything. The higher the compression, the more horsepower you are dealing with, the small that window becomes. Bob knows this all too well.

I'll find a plug that I cut apart, or just cut one today, to show you where to cut them. The Autolite plugs are easier to read without cutting them open than the NGK's are. But once you know the A/F you need to run, you won't be cutting them apart anymore, until you put that blue bottle beside you! :)
 
Here ya go:

kH3zvS3.jpg


The easy setup to take a plug apart.

If you pull plugs looking like this you have problems!

OecsWpy.jpg


There is the fuel ring, in all of it's Opra black fat ass ugliness!
 
Here ya go:

kH3zvS3.jpg


The easy setup to take a plug apart.

If you pull plugs looking like this you have problems!

OecsWpy.jpg


There is the fuel ring, in all of it's Opra black fat ass ugliness!
Ok, now post a picture of a good plug lol
 
Ok, now post a picture of a good plug lol
I'll take a look around. That dark area on that plug should be much lighter in color, light brown is good, and won't be as thick (tall). That was a very fat tune with no timing (nitrous days).
 
This plug has 2 passes on it and one aborted run. Staging and return road for 3 runs.

For discussion sake, if it looked like this after a proper shut down, it’s way too fat, correct?
 
That is Opra fat dude! No beuno.
Maybe impossible to say, but how much is it skewed due to the driving back from the run and to the staging lanes?

I've read stuff that say the idle circuit colors the top of porcelain near the electrode, but has nothing to do with WOT down there, but many others say different.
 
Here is what you want to see:

tU2y6ve.jpg


I drove my car to the lanes with two fresh plugs in it. Did my burnout, made the pass, clicked it after the traps. With EFI it's easy, no fuel getting sucked through a leaky device, I mean carb......... ;)

I don't know if driving back to through the pits would have done much to it, but I have never raced with a carb.

But if I pulled a plug and it looked like that, I know I was doing something wrong. And if I was running nitrous, I would be surprised if my rings still liked me.

It's hard to hurt an N/A engine, too little fuel it makes no power and no heat, too much fuel it falls on it's face, washes the rings if stupid rich, but still in one piece. Timing, well that can start to rattle the pistons and the rings, oil in the chambers is no beuno, and with nitrous, pretty much the end of your day.
 
Back
Top