Breaking up at high rpm, carb issues, and converter issues.

And don't try for the "perfect" timing mark on the straps! Especially if you run Autolites, they only have half a strap to begin with.
Get the A/F close, again, for you, 13.0 to 13.3 A/F should be pretty close. Go down towards 12.5 and up to 13.8 once you have a handle on things.
Timing, well it's a SBF and they typically don't need much timing unlike our SBC with large domes.
Add 2 at a time till the MPH drops off. That's your limit. I can't see it needing more than 38*, and probably far less!
What did your engine builder want you to start with?
Maybe 28* to 30*?
I'm not a SBF guy so I would have to phone a friend for solid advice.
 
And don't try for the "perfect" timing mark on the straps! Especially if you run Autolites, they only have half a strap to begin with.
Get the A/F close, again, for you, 13.0 to 13.3 A/F should be pretty close. Go down towards 12.5 and up to 13.8 once you have a handle on things.
Timing, well it's a SBF and they typically don't need much timing unlike our SBC with large domes.
Add 2 at a time till the MPH drops off. That's your limit. I can't see it needing more than 38*, and probably far less!
What did your engine builder want you to start with?
Maybe 28* to 30*?
I'm not a SBF guy so I would have to phone a friend for solid advice.
I've been runnin sbf's for almost 20 years now and they always do best between 27-36*. My last 2 engines, 393 and 331 ran best at 36*. However, these AFR 220's I've been told that they are designed with a quick burn combustion chamber, and they don't need as much timing. Remember I started out at 24* running a best of 6.00. Bumped timing to 28* and ran 5.90's. 30* ran low 5.80's. Tried 32* a couple of weeks ago and mph dropped off.
 
Not sure how much it will change by going to the colder plugs. Hoping it runs better.
 
that looks like its eroding the center electrode? does the electrode have blisters on it?
that thing is pig fat
No, the electrode is fine. I'm not sure why it looks like that in the pic. I'm staring at it right now and don't see that uneven smudge.

Pig fat? But this isn't after a shut down. This is driving around staging lanes making 1 aborted pass and 2 full passes and back to pits. Are you saying it still shouldn't look like this?

If so that means the wideband really is just a reference number 💡(which many have said) and I need to listen to the soldiers on the ground (spark plugs).
 
that looks like its eroding the center electrode? does the electrode have blisters on it?
that thing is pig fat
So being fat causes blisters...Would you please explain that part ? Thank you.
 
No, the electrode is fine. I'm not sure why it looks like that in the pic. I'm staring at it right now and don't see that uneven smudge.

Pig fat? But this isn't after a shut down. This is driving around staging lanes making 1 aborted pass and 2 full passes and back to pits. Are you saying it still shouldn't look like this?

If so that means the wideband really is just a reference number 💡(which many have said) and I need to listen to the soldiers on the ground (spark plugs).
driving it absolutely changes how it looks.
clean pass and clean shutdown
you cant learn much if you drive it back
everything is poor burn at idle
 
no
detonation causes blisters.
Ok. I blistered a set one day. Got too hot on me. Thought I got a head gasket, but didn't. Thought maybe it was moisture that did it. Was looking for an answer.
 
Last edited:
More lost than I was before. Plug on the left is cylinder #7, plug on the right is #1.

WTF?!?!?!?!


 
AFR gauge read 12.5

Car missed at the top of 1st and the top of 2nd. I pulled the 7800 chip and put in the 9000.

See if that fixes it. I think it came back when I switched it out a couple weeks ago.
 
Into trailer, out of trailer, staging lanes and ran.

Shut down at the end pulled plugs.
Unless you get a clean kill under full power you really can’t get a good reading.

Anything but a clean kill will have mixture issues that will make some plugs look lean & some look fat… like those.

That’s my story & I'm stickin to it. 😄
 
Why such a hot plug? What heat range/part number is that?
 
Back
Top