Leak down test after spewing water at the track

Ok, I was wrong. I have a non-vented in my race car, I forgot I decided to try a recovery system in that car.

Our other car has the vented style.

0Dd3zI5.jpg


That hole in his is too damn perfect for a blow-out. I bet it was a plug designed to be removed. But whatever, he has it handled now.
 
I have never seen an overflow tank with a small hole at the top for a "breather" like some have said.
While tearing down this new to me dragster,I took a look at what someone had done with the catch can.
They must have had a problem with cooling and decided that the solution was to drill a 1/4 inch hole at the top of the aluminum can,insert a piece of plastic tubing,silicone it to the can to "seal" it and run the tubing along the frame rail to exit behind the rear tires and onto the track. WTF.
They were also were running a 30 lb moroso cap.
I tapped the hole they drilled and plugged it. I also installed a 14 lb cap as that is what we use on the Mustang.
While we were doing some heat cycles on the new engine,we were playing with the box for a few minutes waiting for it to warm up got distracted and the cap relieved pressure that blew the hose off the recovery tank and puked water. Quickly turned the pump on and out temp was only at about 180.
Does not seem like it was running very long to do that. So I am a little concerned if it will be an issue ,but with the pump on and fan there is no problem just idling.
I wonder if they had an issue with flow rate on the cross flow rad that is an older unit,also there is no shroud just an average fan zip tied through the rad.
12 -AN lines.
Thinking of going to a larger AFCO double pass radiator with a shroud and larger fan and a cap in the 24 lb range. Hence my earlier question about determine cap pressure size.
That is a nice looking tank you ordered,interested in your outcome this weekend.


I think the difference in the vent/no vent is maybe that one is a “recovery” tank & one is a “surge” tank/ “catch can” ???

I had the same experience when I lost the CSR pump in the puddle. No heat (170) but lotsa mist out of the vent. Venting behind the car is a good move but since I don’t have a hood on this one I decided to put it on the motor plate pointed up so I could see if I had a problem. Sumbitch it worked as I woulda sent it with 170*.
 
I think the difference in the vent/no vent is maybe that one is a “recovery” tank & one is a “surge” tank/ “catch can” ???

I had the same experience when I lost the CSR pump in the puddle. No heat (170) but lotsa mist out of the vent. Venting behind the car is a good move but since I don’t have a hood on this one I decided to put it on the motor plate pointed up so I could see if I had a problem. Sumbitch it worked as I woulda sent it with 170*.
I need to rig up some hoses and a container to visually test my CSR pump that came on the car , I have no idea it’s age or how much water it’s moving . Closed rad so I have no visual of how much water it is actually pushing.
 
I need to rig up some hoses and a container to visually test my CSR pump that came on the car , I have no idea it’s age or how much water it’s moving . Closed rad so I have no visual of how much water it is actually pushing.
Mine was less than a year old & quit @ 8 cars on a good day.

I threw it in the dumpster & bought a Meziere. $550 hurt a little but confidence is priceless to me in a race car.
 
I need to rig up some hoses and a container to visually test my CSR pump that came on the car , I have no idea it’s age or how much water it’s moving . Closed rad so I have no visual of how much water it is actually pushing.
Could you run the return hose into a bucket and time it to figure out gallons per min flow rate?
 
maybe I’m not understanding but whether it is a catch can or a recovery can doesn’t it still have to have a vent in it? When coolant starts coming in it is either going to vent the air displaced or create pressure. What is the purpose of having pressure in the overflow container ??

Sorry for the hi-jack OP just trying to understand the no vent thing
 
maybe I’m not understanding but whether it is a catch can or a recovery can doesn’t it still have to have a vent in it? When coolant starts coming in it is either going to vent the air displaced or create pressure. What is the purpose of having pressure in the overflow container ??

Sorry for the hi-jack OP just trying to understand the no vent thing
In their example with expansion tank the cap is vented.

 
Mine was less than a year old & quit @ 8 cars on a good day.

I threw it in the dumpster & bought a Meziere. $550 hurt a little but confidence is priceless to me in a race car.
CSR pumps suck, simple as that. If you have one and it hasn't died yet, just wait............ I hated paying what Meziere charges, but I have them on both of my cars, will never use anything else except the old Moroso electric drive to spin the stock water pump.
 
CSR pumps suck, simple as that. If you have one and it hasn't died yet, just wait............ I hated paying what Meziere charges, but I have them on both of my cars, will never use anything else except the old Moroso electric drive to spin the stock water pump.
I only put this one back on the fresh engine to get it fired up and broke in.
I called CSR today and gave them the serial number on the pump that came on this dragster. 03/09 . 15 years,guess that was a good one. They told me to send it down ,they would check it out,refresh it ,flow test it,pressure test it and send it back for the cost of shipping. Hard to bad mouth that kind of customer service.
 
I only put this one back on the fresh engine to get it fired up and broke in.
I called CSR today and gave them the serial number on the pump that came on this dragster. 03/09 . 15 years,guess that was a good one. They told me to send it down ,they would check it out,refresh it ,flow test it,pressure test it and send it back for the cost of shipping. Hard to bad mouth that kind of customer service.
That is great customer service! I sold all mt CSR stuff to an engine builder, he uses them for dyno testing. So far so good for him. Hopefully you never have a problem either.
 
Ok, a lot has happened since I posted last. In my quest for trying to figure out what was going on with cylinder #4, I pulled the intake and passenger side head off. Friday morning, I took the parts to an engine builder’s house. He took every valve out one by one and inspected each and every valve and port. He did not find any cracks or anything abnormal. He told me to put it back together. He told me the head gasket looked brand new. No signs of heat anywhere.

I had an extra set of head gaskets at the house, so I got home and went to work. By 7pm I had fired the car off and everything sounded good. All of a sudden I have heat again in cylinder #4. Header primary was getting hot just like the rest. I cracked the throttle and it sounded clean and crisp, so I loaded up the car.

Saturday morning I hit Great Lakes Dragway. First pass car blew the tires off and then I got back in it and the car took off like it was on nitrous. It felt very strong. I got back to the pits and let the car cool off. As I’m headed up for my 2nd pass the car starts breaking up/missing/stumbling/etc., so I turned around and went back to the pits as I suspected #4 might be acting up again. I pulled and looked at every plug. They were all a light gray, not fuel soaked or black. I checked timing and it was good. I noticed that while in park just revving it with my hand that it was breaking up. If I revved it higher to get the secondaries to crack open it cleaned up. I suspected the intermediate circuit of the carb.

I went up and made another pass. I could feel it breaking up while doing my burnout until RPM went up high. On the transbrake it was fine. Taking off at WOT seemed fine. I was fighting traction all day, but still managed to new best 60’. 1.212

The issue remained all day. I tried lowering timing, changing from open adapter to 4 hole adapter, different rev limiter chips, launch rpms. The problem stayed all day. VERY FRUSTRATING.

The only real change from last week is those ceramic balls are no longer blocking the center air bleeds. I thought those air bleeds were only in play at idle?

In a little while I’m going to put the 4150 carb back on and see if it cleans up the missing at part throttle. If it does, I’ll know it’s the carb. If not, maybe I have an ignition issue.

I’m starting to research converting to a 2 circuit, but man I don’t want to start drilling or anything on a brand new carb just yet.

I was fighting the track and missing issue all day.

 
Last edited:
I wish those links were still active. Sucks that I spent good money in a trusted company and having issues (if in fact it's the carb). The more I look into this the more I see some like 3 circuit and some like 2. Obviously for someone like me with limited knowledge, 2 is probably the way to go. Live and learn I guess.


3-circuit-to-2-circuit.png
 
LOL The 3-circuit BS started 55 years ago and is kept alive by media and marketing misinformation, in spite of the fact it has always had the same problem of stinking rich at light throttle and burn up motors lean at WOT.

BLP makes a "Wide Body" 3-circuit metering block that does not have the idle tube in the main well, and so does not suffer from the lean WOT problem, however still has the too-rich at small throttle opening causes by the excessive fuel from the 3th circuit. Perhaps your carb has these blocks? If it does the lever on the accelerator pump diaphragm housing will be bent, offset toward the throttle shaft so it will contact the pump lever (rocker arm). The wide body metering blocks are obviously wider (.850" thick) than regular Holley blocks.

You can use a 2-circuit gasket to block the extra too-rich circuit and recalibrate the idle circuit if it needs it to run better than it does now. Just change the gasket and see if that cleans up the burnout and low speed driving. The only effect or a two circuit gasket will be to eliminate the intermediate circuit.
 
LOL The 3-circuit BS started 55 years ago and is kept alive by media and marketing misinformation, in spite of the fact it has always had the same problem of stinking rich at light throttle and burn up motors lean at WOT.

BLP makes a "Wide Body" 3-circuit metering block that does not have the idle tube in the main well, and so does not suffer from the lean WOT problem, however still has the too-rich at small throttle opening causes by the excessive fuel from the 3th circuit. Perhaps your carb has these blocks? If it does the lever on the accelerator pump diaphragm housing will be bent, offset toward the throttle shaft so it will contact the pump lever (rocker arm). The wide body metering blocks are obviously wider (.850" thick) than regular Holley blocks.

You can use a 2-circuit gasket to block the extra too-rich circuit and recalibrate the idle circuit if it needs it to run better than it does now. Just change the gasket and see if that cleans up the burnout and low speed driving. The only effect or a two circuit gasket will be to eliminate the intermediate circuit.
I just put the 4150 back on and the car is running rough. I think I need to shift my focus elsewhere now. I’m going to check the valves again on the head I just put back on.

I already checked all the grounds and they are good. Fuel pressure is solid at 6psi. This issue seems to have happened right after my first pass.
 
Do you have a dial indicator? If so set it up and roll the motor over by hand and watch the sweep of the rocker tip on two corresponding cylinders, the affected one and one that is running clean.
 
Do you have a dial indicator? If so set it up and roll the motor over by hand and watch the sweep of the rocker tip on two corresponding cylinders, the affected one and one that is running clean.
Looking at the plugs, there is no longer a black one.
I just checked the valves on the head that I had off and they were all on the tight side. I set them at .008” cold and now when I checked them I couldn’t get the feeler gauge in there. I reset them all at .008” just feeling slight drag. Went through and checked them twice all good.

I fired off the car, which still has the 4150 on it and it’s hard to tell if it’s gone, but man when I crack it to where the secondaries open and start spraying fuel this bitch sounds good if I do say so myself. 😁

I’m going to throw the Dominator back on and see how it feels. Isn’t this fun? 😂
 
No. You give me anxiety.
😂
I reset the valves on that side and reset idle. Set 4 corners for highest vacuum and I think it sounds much better now. I hooked up a wide band to the passenger side bank and both sides are very close.
 
Back
Top