Leak down test after spewing water at the track

It was a 5.0 CID intake with a 6500 throttle body on the 376ci above. I forgot it was mentioned in the vid. Play it from 14:15 minutes
Now knowing that my intake is a 4.0 and not a 3.0, I definitely want to try the CID when it hits the market. Maybe because my car never see below 6000rpm the extra plenum size won’t matter. Like you’re saying the design of the runners might be more important than the volume.

It will be nice to have actual comparisons between the two.
 
9a2y53.jpg
 
I got a question.
You ever wonder about that ultra grey that squeezes into the bypass port and closes it off? 😒🤔
No bypass needed, I'm not running a thermostat. I just put the permatex there, so it doesn't leak out of that bypass port on the intake. The plate with -16an fitting on it blocks it off. 😁
 
No bypass needed, I'm not running a thermostat. I just put the permatex there, so it doesn't leak out of that bypass port on the intake. The plate with -16an fitting on it blocks it off. 😁
That blob of RTV that was a plug aggravated my ADD.
AND @89 Fox SBF , that's sort of a conundrum for you ain't it? "Enjoying what you have"?
 
That blob of RTV that was a plug aggravated my ADD.
AND @89 Fox SBF , that's sort of a conundrum for you ain't it? "Enjoying what you have"?
On that note it bothers me that the -16an fitting is not centered on the intake hole. Look at the silicone on that part. WTF Moroso?
 
Even worse.

Can't enjoy what I have.

Can't afford more parts.
Ah, you soon will, Big Daddy's going to the White House and your opportunities will be many.
New York is already bussing illegals back to Texas right now.
 
I just measured the ports on the BMP and it’s definitely a 4.0.

It’s tricky to get your hands and a tape in the plenum, but I got roughly 1.625” x 2.5” =4.0625”

Too close to 4.0 to be a 3.0”. That gives me some insight and the 4.5 doesn’t seem so big now.
I had some playdoh for check PTV clearance, and I clayed one of the ports on the 4150 BMP. It’s definitely not a 3.0.

I measured 1.625” x 2.625” = 4.265”


IMG_7415.jpeg
IMG_7416.jpeg
 
Last edited:
I will be mounting my new Meziere overflow bottle today. I had to order some aluminum spacers and hardware from McMaster to mount it. The instructions say that they recommend running the vent line to the back of the car, so I did just that.

After my overflow popped it had me thinking. If that would have happened on the track it was probably game over. This way if it overflows it will exit behind the tires in the center of the car.

IMG_7400.jpeg

Mezeire-recovery-tank.png
 
Last edited:
I had some playdoh for check PTV clearance, and I clayed one of the ports on the 4150 BMP. It’s definitely not a 3.0.

I measured 1.625” x 2.625” = 4.265”


IMG_7415.jpeg
IMG_7416.jpeg
I text this info to Sam Vincent yesterday and he said that the CSA of measurement is not at the port in the plenum and that it’s midway into the port. He assured me that the BMP is based on the CHI Commander 3.0 and NOT the 4.0.

I received the 4500 BMP last night and just like the 4150 BMP, the fucker doesn’t fit. It will have to be milled. I might send this thing back. I’m going to talk to some folks at PRI.

For now I ordered new intake gaskets. They will be here Thursday and I’ll put it back together again. Track is out of C12, so I’ll be trying VP113 or Q16. I’ll probably do 113 since it’s cheaper. I’ll start by going up .004 jet on all 4 corners and see what happens.
 
CID might end up making a 4.0 version for your heads, you think they would seeing as they have the 4.0/4.5/5.0 for the other heads and engines. Or maybe John is right that the 4.5 isn't too big and he won't bother with a 4.0. Maybe they've sold a lot less 4.0 versions than the 4.5 and 5.0

While i'm here this car below also had the 5.0 CID with 4500 tb. 440ci, 14:1cr

2nd time out since built, n/a pass. He hasn't been back with updates since then, i'm sure this car had a lot more in it still (where's @89fox lol)

I think the CID 4.5 intake would work well, the fact that GPI also had the 5.0 on only a 376ci only turning 8200rpm or so (i say only because it was a stock stroke 376ci) and he said the 4500 tb was a restriction and went to a 6500 tb is funny

If i order one for mine i'm thinking to get the 5.0 now after looking at more cars. With my heads/cam i'm already shifting at 8k and it doesn't drop off. And if i decide to throw a stroker crank or even a bigger CI short block in it the 5.0 will probably work



img_1144_63a3be0e0121a296a8a558611a68021cf78e982c.jpeg
BMP told me yesterday that the LS heads are better. Basically told me I need bigger heads. I have never looked into a single thing about an LS other than what you send me, so maybe we’re not comparing apples to apples. Maybe the AFR’s are the Achilles heel for the CID to work.

I would hate to spend $1000+ to have the car slow down.
 
The LS is basically a windsor with 6 bolt mains :ROFLMAO: but seriously i mentioned the CID intake to you because it got me thinking that why wouldn't it work? Especially a 4.0 version. It's a superior design to all the other 'spider' single planes. Wait to see what CID does what results they put out and you can decide then

Your heads aren't too far off LS heads flow #s and you have 427ci, 13:1cr and a fairly big roller cam. How can a better design intake not gain.... seems unlikely to me. Are these your heads below? Flow numbers are about what a good ported cathedral head for an LS is, a bit under LS3/LS7 heads, but not by a heap

220cc Street Head Flow Chart
.200.300.400.500.600.700.800
Int135194258295315325331
Exh121171215238245249250
Test conducted at 28" of water (pressure) on Superflow 1020
Bore Size: 4.155", 3/4" radius plate exhaust, 1 7/8" curved pipe
​
Yes, those are the heads, but Weingartner and others have said that those numbers were inflated by AFR. Weingartner flowed them and there is a video, but I can't remember what they actually flowed.

John told me it will be a 4.5". He didn't say anything about a 4.0". Even so, that's fucking huge! I'm being told by every other engine builder that I've talked to that the 4.0" intakes are too big for these heads. Is John the only one that knows this magic pill? He did say in his frustration that the intake will not make power on every combo. I don't know why he got all pissy instead of just explaining why he thinks it will make power for me.
 
If i'm wrong then i guess CID might post results for their Windsor intake on something more radical than your engine

But again just thinking common sense, 427ci, 13:1cr, big roller, very light car, 330 cfm heads .... a CID intake would beat the other intakes, like it does on LS's .... that was my thinking
I highly doubt it was tested with AFR 220's. He would have told me when I told him what heads I have. It was likely using heads much bigger than mine. That is my guess.
 
Mine was less than a year old & quit @ 8 cars on a good day.

I threw it in the dumpster & bought a Meziere. $550 hurt a little but confidence is priceless to me in a race car.
What series Meziere pump do you have? Same question to you @Mike Beck and @Patriot Racer ?
I had to do it this way as the multi quote function does not work on here for me lately.
 
What series Meziere pump do you have? Same question to you @Mike Beck and @Patriot Racer ?
I had to do it this way as the multi quote function does not work on here for me lately.
I have the WP311 55ga pump. The CSR was 35-37ga. I’m not sure if you remember, but there was nothing wrong with my CSR. I just didn’t have the block filled up enough for it to continue pumping water. I learned that I had to jack the front of the car up and fill it through the intake manifold.

I’m happy I switched, but it wasn’t 100% necessary.

Edit: with -16an lines I have you can’t squeeze them to get the water moving.
 
Last edited:
Back
Top