Leak down test after spewing water at the track

Patriot Racer

Freeeeeeedom!
Joined
Sep 18, 2021
Messages
9,229
Reaction score
24,327
Points
153
Location
Northern Illinois
Those of you following the drag racing 2024 thread probably saw my anomaly that happened last weekend. Car got hot after a pass and when I got back to the trailer it blew an 1/8” hole in my overflow bottle and spewed water out.

IMG_7295a9016f3c6b37400a.jpeg


I called Ron Davis this morning and he told me to check the radiator fins and do a leak down test to make sure that I didn’t blow a head gasket. I was planning the leak down test anyway. He told me some other stuff to check like voltage to water pump and fan, electrolysis, etc.

I started pulling plugs to prep for the leak down test and cylinder #4’s plug made me poop myself. Looks like oil on the plug. (Maybe it’s soot from being rich?)

IMG_7322.jpeg


Onto the leak down test. The test was performed @ 80 psi.
#1) 72 PSI = 10%
#2) 73 PSI = 8.75%
#3) 70 PSI = 12.5%
#4) 72 PSI = 10% (plug I thought had oil)
#5) 74 PSI = 7.5%
#6) 72 PSI = 10%
#7) 69-70 PSI = 12.5% - 13.75% (worst cylinder)
#8) 70 PSI = 12.5%

I’m going to check a few things in the cooling system. Drain and refill it, new plugs, weld the hole in the overflow bottle, and go racing Friday if nothing else is found.

What are your guys thoughts on the leak down numbers and that black plug?
 
I'm sure you did, but the pistons were at TDC when checked, correct?

Do you know what your ring gaps are?

I think 10% is normal, doesn't seem that far out of range.

But I'm the Forest Gump of car knowledge here so free bump.
 
I'm sure you did, but the pistons were at TDC when checked, correct?

Do you know what your ring gaps are?

I think 10% is normal, doesn't seem that far out of range.

But I'm the Forest Gump of car knowledge here so free bump.
Yes, TDC. I don't remember what ring gaps are.
 
Unfortunately I can’t help but that hole looks perfectly round, did it have a plug of some sort in it?
Nope. It blew that out just like that. Ron Davis said maybe something was in there stuck to the bottom corroding and when it pressurized it blew it out. Sounds far fetched, but how else did it happen? Crazy.
 
Might be out there, but I wonder if #4 had simply been misfiring? Bad wire, etc.? Take care. Tom Worthington
Very likely. I think the car is very rich at part throttle while driving in the pits. It's fine at idle and WOT. When I pulled the plugs, several of them were wet with fuel. Only a couple were dry as a bone.
 
Those of you following the drag racing 2024 thread probably saw my anomaly that happened last weekend. Car got hot after a pass and when I got back to the trailer it blew an 1/8” hole in my overflow bottle and spewed water out.

IMG_7295a9016f3c6b37400a.jpeg


I called Ron Davis this morning and he told me to check the radiator fins and do a leak down test to make sure that I didn’t blow a head gasket. I was planning the leak down test anyway. He told me some other stuff to check like voltage to water pump and fan, electrolysis, etc.

I started pulling plugs to prep for the leak down test and cylinder #4’s plug made me poop myself. Looks like oil on the plug. (Maybe it’s soot from being rich?)

IMG_7322.jpeg


Onto the leak down test. The test was performed @ 80 psi.
#1) 72 PSI = 10%
#2) 73 PSI = 8.75%
#3) 70 PSI = 12.5%
#4) 72 PSI = 10% (plug I thought had oil)
#5) 74 PSI = 7.5%
#6) 72 PSI = 10%
#7) 69-70 PSI = 12.5% - 13.75% (worst cylinder)
#8) 70 PSI = 12.5%

I’m going to check a few things in the cooling system. Drain and refill it, new plugs, weld the hole in the overflow bottle, and go racing Friday if nothing else is found.

What are your guys thoughts on the leak down numbers and that black plug?

How stiff is your radiator cap?

I had a w/p failure on the burnout & had a fine mist spewing out of my overflow tank vent & hitting my visor while staging. It was 160* when I lit the tires so it happens quick.
 
How stiff is your radiator cap?

I had a w/p failure on the burnout & had a fine mist spewing out of my overflow tank vent & hitting my visor while staging. It was 160* when I lit the tires so it happens quick.
Ron Davis said it’s an 18lbs cap. I asked what max pressure is for their radiators and he said they test at 32psi cold. However, the higher lbs cap will just raise the boiling point. If the cap failed it must have gotten stuck closed and then decided to pop.
 
How stiff is your radiator cap?

I had a w/p failure on the burnout & had a fine mist spewing out of my overflow tank vent & hitting my visor while staging. It was 160* when I lit the tires so it happens quick.
Great question ,and I have been trying to determine what pressure cap to use on my dragster. So My question is how do I know what psi cap to use?
 
Ron Davis said it’s an 18lbs cap. I asked what max pressure is for their radiators and he said they test at 32psi cold. However, the higher lbs cap will just raise the boiling point. If the cap failed it must have gotten stuck closed and then decided to pop.

If it’s never done it before, your cap may be failing by popping off at lower pressure & spitting out enough water to overheat it… or you had a big pressure spike for some reason. Caps are a lot cheaper than anything else.

Great question ,and I have been trying to determine what pressure cap to use on my dragster. So My question is how do I know what psi cap to use?

I have always run the highest I can get my hands on for both circle track & drag racing.
I currently have a PRO TEK rated at 24lbs.
 
Might be out there, but I wonder if #4 had simply been misfiring? Bad wire, etc.? Take care. Tom Worthington
That plug does not have a vigorous "spark mark" on the center electrode, as if the ignition energy is weak in that cylinder.
 
That plug does not have a vigorous "spark mark" on the center electrode, as if the ignition energy is weak in that cylinder.
None of these NGK plugs ever have a vigorous spark mark. As a matter of fact I can never even see the damn thing.
 
None of these NGK plugs ever have a vigorous spark mark. As a matter of fact I can never even see the damn thing.
That is not the fault of any brand of plug. If the energy is there it will etch the electrodes, and at least clean the carbon, oil or fuel, off the electrodes in the spark gap. What kind of coil is it?
 
That is not the fault of any brand of plug. If the energy is there it will etch the electrodes, and at least clean the carbon, oil or fuel, off the electrodes in the spark gap. What kind of coil is it?
coil.png
 
According to MSDs marketing specs that should make a spark. They market so many different coils with such varied specifications they are sure to satisfy a broad range of consumers' opinions about what detail is important.

One thing I have noticed is when the specification of maximum voltage increases, the inductance and spark duration decreases, and I think there is a point where longer spark duration is more important than a theoretical higher voltage that the system will only reach if a wire is open or not connected to a plug at all.

Nevertheless, the one plug looking like does and the others not fouled surely indicates something amiss with that cylinder. Have you used an ohmmeter and measured that plug wire resistance and compared it to the others ? Do you have any close up pictures of the other plugs ?

That conical piece missing from the catch tank looks like the hole in a plate glass window that has been shot with a BB or pellet gun
 
That plug looks like it's not firing. Don't think it's oil
I’m going to throw one of these on later today after work to see if it’s firing. I could have fouled the plug with too much fuel. It’s been hard to start since putting the Dominator on. I think I have to lean it out. The back corners are always a problem on SBF’s.

IMG_7326.jpeg
 
Last edited:
According to MSDs marketing specs that should make a spark. They market so many different coils with such varied specifications they are sure to satisfy a broad range of consumers' opinions about what detail is important.

One thing I have noticed is when the specification of maximum voltage increases, the inductance and spark duration decreases, and I think there is a point where longer spark duration is more important than a theoretical higher voltage that the system will only reach if a wire is open or not connected to a plug at all.

Nevertheless, the one plug looking like does and the others not fouled surely indicates something amiss with that cylinder. Have you used an ohmmeter and measured that plug wire resistance and compared it to the others ? Do you have any close up pictures of the other plugs ?

That conical piece missing from the catch tank looks like the hole in a plate glass window that has been shot with a BB or pellet gun
I wonder if I’m getting a voltage drop from the coil. The length of 14ga wire is approximately 7’ maybe more. It runs from drivers side fender under hood to inside floor board on passenger side.

I’m not saying that is the cause of #4 misfiring, but maybe it’s not helping spark energy?

I’ll check voltage at the coil later. Getting ready for work.
 
Unfortunately I can’t help but that hole looks perfectly round, did it have a plug of some sort in it?

I'm with the chief. My overflow bottle has a small hole in it at the TOP to allow it to breath. I run the rad line to the bottom of the bottle to use it has a recovery bottle. How is yours run?

What's the heat range on the plug? How much run time on that set? I'd say the idle,part throttle,and transition tuning is why they are fouled.
 
Back
Top