I found a bunch of gold! I'm rich!

Well, now what

  • Change the oil, run it a few more miles, check again

    Votes: 32 78.0%
  • Pull it apart.

    Votes: 9 22.0%

  • Total voters
    41
I was having problems with my race car years ago. Put on a set of ported Brodix heads, car can fine, but when I lifted in the top end my car disappeared in a cloud of smoke. Was embarrassing, never a drop of liquid on the track. I got pissed one day and turned the rev limiter off and let it go to 8000. Well, that wasn't smart, fell on it's face, popping and farting, put it on the trailer and said fuck this piece of shit. Was barely in the 10's at the time.

So, I make the long tow home, 9 miles, a friend of mine follows me, my house is on his way home. I put the shit box in the driveway, spit on it, my friend walks over, goes in the car pops the hood, asks me where are my f-ing tools, this bitch is coming apart! Engine was still warm! Pull the valve covers, found a broken rocker stud and bent pushrod. We can see the epoxy by a few pushrods was cracked which was letting oil into the runner under high vacuum. He pulls the lower radiator hose (just plain water in the engine) and within an hour both heads are off! I would have let that bitch sit and rot for quite sometime, I was fed up.

Took those heads to a really good fabricator who removed all the epoxy and sleeved that area with some sort of bronze liners. It's a long time ago, but after he fixed them I never had an issue again. Also learned that ARP had different grades of screw in studs. I had bought the "weaker" studs. So I went all-in at that time and got their best studs, plus studs for a BBC which were 7/16" instead of the SBC 3/8" which required new rockers. I used shaft rockers now, their is no comparison, but I was a really broke ass bitch back then with my turd on an open trailer.
 
I’m having a hard time with this oil situation. Run to NAPA, grab a case of Brad Penn. Thats all I use in mine. Works just fine.

It’s oil, not a dick. No need to make it hard.

What's amusing about this...

I started a thread years ago about needing break in oil or not. The members of the forum would say you absolutely need break in oil or an additive for the first few hundred. Same members would later say check the oil and filter after 50 miles then put in your oil of choice.

I wish I would keep a running tally of the members going backwards on previous recommendations.

Its the mob mentality. Jump on because others jump on. Reminds of the Garry threads or the hugh/dually threads.

I take the advice of very few from here, but making a thread keeps half the place entertained for 2 days.
 
I always recommend high detergent straight 30 for break-in. I have never used anything else.
I also have never put in a flat tappet cam, all my stuff has been some sort of roller.
Maybe a flat tappet requires something different, but yours is a roller so HD 30 is just fine.

You're right about the Charlie Brown flip-flopping....... :)
 
What's amusing about this...

I started a thread years ago about needing break in oil or not. The members of the forum would say you absolutely need break in oil or an additive for the first few hundred. Same members would later say check the oil and filter after 50 miles then put in your oil of choice.

I wish I would keep a running tally of the members going backwards on previous recommendations.

Its the mob mentality. Jump on because others jump on. Reminds of the Garry threads or the hugh/dually threads.

I take the advice of very few from here, but making a thread keeps half the place entertained for 2 days.
I just got my engine back from Sonny's recently. They use Maxima Racing Oils break in oil. I was told to run 1 tank of gas through it, and then change the oil to Mobil 1 10W-30 Fully Synthetic. Told him I had a small gas tank, and this thing doesn't get good gas mileage. He said "I know that...Change the oil !"
 
I've lost track of how many of those pieces of shit I've seen fail on Chevy applications, including my own car. If you're lucky enough to get the one person left at Comp that knows anything, they don't recommend them for wet sump applications. I am happy they have worked out for you though.
Chevys have a larger gear. Some pretty successful race engine people say that for a FORD, the composite gear is good. Comp Cams suggests it for this type of setup. (Disclaimer) I never willingly use ANY comp cam products.😜
 
What's amusing about this...

I started a thread years ago about needing break in oil or not. The members of the forum would say you absolutely need break in oil or an additive for the first few hundred. Same members would later say check the oil and filter after 50 miles then put in your oil of choice.

I wish I would keep a running tally of the members going backwards on previous recommendations.

Its the mob mentality. Jump on because others jump on. Reminds of the Garry threads or the hugh/dually threads.

I take the advice of very few from here, but making a thread keeps half the place entertained for 2 days.
No mob mentality here. I suggested the cheaper oil just to run it and see if it filled up with flakes or not. That would tell you if there is an on going problem or if it was break in. I will no longer offer you advise in the future.
 
I usually have my engines built by a pro shop with access to a dyno. They do the break-in & dyno pull & I get a spec sheet. They drain it, fill it with VR1 & we are good. No leaks, and I get the power I paid for.
 
I usually have my engines built by a pro shop with access to a dyno. They do the break-in & dyno pull & I get a spec sheet. They drain it, fill it with VR1 & we are good. No leaks, and I get the power I paid for.
I’m the flip side of that coin…
Build my own motors, break them in myself, drain it and fill it with VR1..
Dyno pulls are seat of the pants,
I get the power “I” built.
If it scatters, no one to blame but myself, I’ve built thousands of engines and compressors in my lifetime and have learned something valuable from every single one of them..

OP needs to get on with refilling the oil, give it a spin and see how things go… and look at this as a learning experience. If the motor has an issue, it will tell you. But delaying the process is not going to magically fix it if it’s toast .
 
I’m the flip side of that coin…
Build my own motors, break them in myself, drain it and fill it with VR1..
Dyno pulls are seat of the pants,
I get the power “I” built.
If it scatters, no one to blame but myself, I’ve built thousands of engines and compressors in my lifetime and have learned something valuable from every single one of them..

OP needs to get on with refilling the oil, give it a spin and see how things go… and look at this as a learning experience. If the motor has an issue, it will tell you. But delaying the process is not going to magically fix it if it’s toast .

Not my house, not my garage. If I could go there at 9pm and sort it out I would.

The lesson for me on the next one is exactly that.. build it myself so there's no one to blame and no speculation on what parts or tolerances were there
 
I’m the flip side of that coin…
Build my own motors, break them in myself, drain it and fill it with VR1..
Dyno pulls are seat of the pants,
I get the power “I” built.
If it scatters, no one to blame but myself, I’ve built thousands of engines and compressors in my lifetime and have learned something valuable from every single one of them..

OP needs to get on with refilling the oil, give it a spin and see how things go… and look at this as a learning experience. If the motor has an issue, it will tell you. But delaying the process is not going to magically fix it if it’s toast .
I've built a few but nothing like you have. Usually when I'm building a car, I'm busy with other crap like paint, suspension & other stuff so I usually just have engine built. Same with trans too. I just use a bare block for fab.
 
Chevys have a larger gear. Some pretty successful race engine people say that for a FORD, the composite gear is good. Comp Cams suggests it for this type of setup. (Disclaimer) I never willingly use ANY comp cam products.😜
Fuck I had awesome luck with comp products for 20 years. I haven't used any in the last 15 probably though
 
Not my house, not my garage. If I could go there at 9pm and sort it out I would.

The lesson for me on the next one is exactly that.. build it myself so there's no one to blame and no speculation on what parts or tolerances were there
No- the lesson is to use someone you trust, not someone you have never used before.

I got pics like this almost daily during the last build
I was always encouraged to drop in anytime to see what's going on.

 
Back
Top