I found a bunch of gold! I'm rich!

Well, now what

  • Change the oil, run it a few more miles, check again

    Votes: 32 78.0%
  • Pull it apart.

    Votes: 9 22.0%

  • Total voters
    41
Since this isn't anyone else's dime, they say fuck it, run it, see what happens.

The fact is the engine is toast and needs to come apart. Will it make noise and go down the road a few more times? Sure. Will the bearings turn to dust? Guaranteed.

If anyone here truly believes that amount of bearing material and ferrous shit is going to work itself out you're crazier than online dating chicks.

After i idle this engine 10 minutes to prove how fuckin stupid i am, this engine is coming out, being stuffed in the corner, and this project is essentially dead.

In case you guys didn't follow along in the build thread.. 3 different builders fucked me, over $20k into this 400hp (not joking) engine. I'm not putting another dime into it.
Fuck, if that's the case, put some cheap ass oil in it and go fry those fucking tires off! Stress relieving burnouts are fun.
 
Did you go in through the drain hole with a magnet to see what is in the pan? Does it have a magnetic drain plug? If another short run time puts more junk in the filter then put it on an engine stand and take it apart, let's see what is the problem.
 
Did I miss any info on what the oil looked like out of the pan? Your boat mettalic flakes were out of the filter, correct. I don't know why, but my backwards ass, country fuck mind would want to put the drain plug in, put some diesel fuel in it then pull the plug and flush what I could out of the pan. Don't really know just thinking out loud.

Why would you use diesel fuel?
 
Since this isn't anyone else's dime, they say fuck it, run it, see what happens.

The fact is the engine is toast and needs to come apart. Will it make noise and go down the road a few more times? Sure. Will the bearings turn to dust? Guaranteed.

If anyone here truly believes that amount of bearing material and ferrous shit is going to work itself out you're crazier than online dating chicks.

After i idle this engine 10 minutes to prove how fuckin stupid i am, this engine is coming out, being stuffed in the corner, and this project is essentially dead.

In case you guys didn't follow along in the build thread.. 3 different builders fucked me, over $20k into this 400hp (not joking) engine. I'm not putting another dime into it.
You will always be Fox 351 to me. :(
 
Did you go in through the drain hole with a magnet to see what is in the pan? Does it have a magnetic drain plug? If another short run time puts more junk in the filter then put it on an engine stand and take it apart, let's see what is the problem.

No I did not. I haven't been back to drain the oil yet because of my work schedule.

I don't have anywhere to take the engine out. I've been asked to get this car out of her barn. It will be trailered to a field in west Virginia until I get my own place to work on it or light it on fire. I wish it wasn't the case but that's the hand I've been dealt.
 
I get it now. You are the only one with any experience. Nobody but you has anya experience or knows anything, so you can shit talk and everybody else can only listen.

You said you are the king of shit in post 185, so I took you at your word.

I don't care where you are, where you will be, or when you will be there, so go talk your shit where and whenever it pleases you.

What a great thread. Has the second oil filter been autopsied yet?
show me where I said I was the king of anything in post 185 ? In fact, I suck at racing , I am as far from king of racing as you can get. I never said anything but that in any thread.
I was giving my real life experience with products .

I am sorry , I did not mean to step on your toes , after all you went 3 rounds several years ago.
It might have taken you 3 distributor gears to get to that point, but ya did it.

Are you still going to pretend that you have no idea why I think you are a cunt?
You know exactly why .
 
Last edited:
I don't have anywhere to take the engine out. I've been asked to get this car out of her barn. It will be trailered to a field in west Virginia until I get my own place to work on it or light it on fire. I wish it wasn't the case but that's the hand I've been dealt.

Excuses excuses.


 
so the Tony Beets of the mustang world officially gives up..!

tune in next week same time same channel for more interactive internet insanity.. :facepalm:
 
In case you guys didn't follow along in the build thread.. 3 different builders fucked me, over $20k into this 400hp (not joking) engine. I'm not putting another dime into it.

Don't make it worse by putting a window in the block.
I'd pull it and rip the fucker apart. To me it's better to be safe than sorry.

For a few pennies more you could have this, endorsed by PB's own DHR Darren


 
I
No I did not. I haven't been back to drain the oil yet because of my work schedule.

I don't have anywhere to take the engine out. I've been asked to get this car out of her barn. It will be trailered to a field in west Virginia until I get my own place to work on it or light it on fire. I wish it wasn't the case but that's the hand I've been dealt.
Tow that fucker to Bangr's. He needs a new project! :ROFLMAO:

Please don't park in a field to become mouse infested and rot away.
 
Or broke, not sure.




Looking at it again closer, it really doesn’t look that bad. I think you’re trippin unless there’s some new info I didn’t get. If you’re concerned about bearings, that’s not bearing material. Everytime I’ve seen bearings come up in a filter it’s dark or brown bigger flakes not small gold pieces. If that engine runs good, doesn’t rattle, I’d screw a system 1 on it and just monitor it. Pull the valve covers and look along the drain backs see what the oil looks like and what it’s been leaving behind. Draining the first oil always looks a little funky from all the assembly lube. I think you’re overreacting myself but do what makes you feel good about it, after all it’s your dime
 
No I did not. I haven't been back to drain the oil yet because of my work schedule.

I don't have anywhere to take the engine out. I've been asked to get this car out of her barn. It will be trailered to a field in west Virginia until I get my own place to work on it or light it on fire. I wish it wasn't the case but that's the hand I've been dealt.
Drop it off here on the way to WV I’ll pull the motor out and take it to a reputable builder for you .
 
show me where I said I was the king of anything in post 185 ? In fact, I suck at racing , I am as far from king of racing as you can get. I never said anything but that in any thread.
I was giving my real life experience with products .

I am sorry , I did not mean to step on your toes , after all you went 3 rounds several years ago.
It might have taken you 3 distributor gears to get to that point, but ya did it.

Are you still going to pretend that you have no idea why I think you are a cunt?
You know exactly why .
I know why. You don't know why. You haven't got a clue.
 
At this point it’s already aggravated the fuck out of you so you might as well get some enjoyment from it. Keep an eye on the oil and run the fuck out of it.

I went through something similar. Bad machine shops, shit parts etc etc then lost a cam once i had the rest sorted out. I put a new cam and lifters in it, Watched the oil like it was going to steal from me and it’s been fine for five years.
 
Back
Top