Oh geeze, you really did it this time. Now he will start a thread begging for advice on what to do about thatShit or get off the pot!
Oh geeze, you really did it this time. Now he will start a thread begging for advice on what to do about thatShit or get off the pot!
I’m having a hard time with this oil situation. Run to NAPA, grab a case of Brad Penn. Thats all I use in mine. Works just fine.
It’s oil, not a dick. No need to make it hard.
LOL I'm stealing thatIt would feel like neighborly automotive rape, but not friendly, at all.
I just got my engine back from Sonny's recently. They use Maxima Racing Oils break in oil. I was told to run 1 tank of gas through it, and then change the oil to Mobil 1 10W-30 Fully Synthetic. Told him I had a small gas tank, and this thing doesn't get good gas mileage. He said "I know that...Change the oil !"What's amusing about this...
I started a thread years ago about needing break in oil or not. The members of the forum would say you absolutely need break in oil or an additive for the first few hundred. Same members would later say check the oil and filter after 50 miles then put in your oil of choice.
I wish I would keep a running tally of the members going backwards on previous recommendations.
Its the mob mentality. Jump on because others jump on. Reminds of the Garry threads or the hugh/dually threads.
I take the advice of very few from here, but making a thread keeps half the place entertained for 2 days.
Chevys have a larger gear. Some pretty successful race engine people say that for a FORD, the composite gear is good. Comp Cams suggests it for this type of setup. (Disclaimer) I never willingly use ANY comp cam products.I've lost track of how many of those pieces of shit I've seen fail on Chevy applications, including my own car. If you're lucky enough to get the one person left at Comp that knows anything, they don't recommend them for wet sump applications. I am happy they have worked out for you though.
No mob mentality here. I suggested the cheaper oil just to run it and see if it filled up with flakes or not. That would tell you if there is an on going problem or if it was break in. I will no longer offer you advise in the future.What's amusing about this...
I started a thread years ago about needing break in oil or not. The members of the forum would say you absolutely need break in oil or an additive for the first few hundred. Same members would later say check the oil and filter after 50 miles then put in your oil of choice.
I wish I would keep a running tally of the members going backwards on previous recommendations.
Its the mob mentality. Jump on because others jump on. Reminds of the Garry threads or the hugh/dually threads.
I take the advice of very few from here, but making a thread keeps half the place entertained for 2 days.
No mob mentality here. I suggested the cheaper oil just to run it and see if it filled up with flakes or not. That would tell you if there is an on going problem or if it was break in. I will no longer offer you advise in the future.
I’m the flip side of that coin…I usually have my engines built by a pro shop with access to a dyno. They do the break-in & dyno pull & I get a spec sheet. They drain it, fill it with VR1 & we are good. No leaks, and I get the power I paid for.
I’m the flip side of that coin…
Build my own motors, break them in myself, drain it and fill it with VR1..
Dyno pulls are seat of the pants,
I get the power “I” built.
If it scatters, no one to blame but myself, I’ve built thousands of engines and compressors in my lifetime and have learned something valuable from every single one of them..
OP needs to get on with refilling the oil, give it a spin and see how things go… and look at this as a learning experience. If the motor has an issue, it will tell you. But delaying the process is not going to magically fix it if it’s toast .
I've built a few but nothing like you have. Usually when I'm building a car, I'm busy with other crap like paint, suspension & other stuff so I usually just have engine built. Same with trans too. I just use a bare block for fab.I’m the flip side of that coin…
Build my own motors, break them in myself, drain it and fill it with VR1..
Dyno pulls are seat of the pants,
I get the power “I” built.
If it scatters, no one to blame but myself, I’ve built thousands of engines and compressors in my lifetime and have learned something valuable from every single one of them..
OP needs to get on with refilling the oil, give it a spin and see how things go… and look at this as a learning experience. If the motor has an issue, it will tell you. But delaying the process is not going to magically fix it if it’s toast .
Fuck I had awesome luck with comp products for 20 years. I haven't used any in the last 15 probably thoughChevys have a larger gear. Some pretty successful race engine people say that for a FORD, the composite gear is good. Comp Cams suggests it for this type of setup. (Disclaimer) I never willingly use ANY comp cam products.![]()
No- the lesson is to use someone you trust, not someone you have never used before.Not my house, not my garage. If I could go there at 9pm and sort it out I would.
The lesson for me on the next one is exactly that.. build it myself so there's no one to blame and no speculation on what parts or tolerances were there

Not my house, not my garage. If I could go there at 9pm and sort it out I would.