I found a bunch of gold! I'm rich!

Well, now what

  • Change the oil, run it a few more miles, check again

    Votes: 32 78.0%
  • Pull it apart.

    Votes: 9 22.0%

  • Total voters
    41
That is accurate. My rockers are full of stripper glitter.


Whoa there one moment.
Would you consider removing one rocker so that we might rule out the roller tip contact location on top of valve stem?
Should be a witness mark by now.
 
Whoa there one moment.
Would you consider removing one rocker so that we might rule out the roller tip contact location on top of valve stem?
Should be a witness mark by now.
Witness marks look good, I had them off. Some look crooked as fuck when the lash is set but they mark across the center of the valve tip.

I don't know what kit it is but the lifters are linked with a bar
 
Witness marks look good, I had them off. Some look crooked as fuck when the lash is set but they mark across the center of the valve tip.

I don't know what kit it is but the lifters are linked with a bar

(y)
 
Cam or lifters should have come with an adjustment procedure… can’t comment on how to adjust them without more info about what cam and lifters you are running… but basically all hydraulic lifters must be “centered” or preloaded in the bore to operate properly…

Chevy lifters, you back them off till it chatters, then tighten till it stops chattering and then half to three quarters turn more while idling…

… or you can go thru the firing order procedure cold and take up the slack and preload certain valves, roll the motor 180 degrees and adjust the remaining valves. This makes sure the lifters are on the base circle of the lobes… I prefer this method and it’s never missed being spot on.. and a lot less messy.
Hydraulic lifters have a preload spec, usually around 40 thousandths. The "# of turns" method is not the way I've done it, no consistency. Dial indicator and setting the preload you never have to worry. On non adjustable rockers like an LS, you have to set preload with pushrod length.
 
Lifters won’t cause that, and some clatter is normal, which I wouldn’t worry about.
Since most is concentrated to the oil filter I would run it around the block at a decent rpm, then cut apart the new filter for inspection, if there’s any more filings I would drop the pan. I am aware dropping the pan is a bitch, but if it was me, working in a garage on the floor, I would get the car up on blocks, support the engine from the top with a bar, or support the crank snout securely with a jack, then drop the k-member, pan comes off easy after that, but it’s still a ton of work, I’d say at least 4 hours.
I didn’t read most of the chatter in here, so this may have been covered.
 
Lifters won’t cause that, and some clatter is normal, which I wouldn’t worry about.
Since most is concentrated to the oil filter I would run it around the block at a decent rpm, then cut apart the new filter for inspection, if there’s any more filings I would drop the pan. I am aware dropping the pan is a bitch, but if it was me, working in a garage on the floor, I would get the car up on blocks, support the engine from the top with a bar, or support the crank snout securely with a jack, then drop the k-member, pan comes off easy after that, but it’s still a ton of work, I’d say at least 4 hours.
I didn’t read most of the chatter in here, so this may have been covered.
How dare you refer to all this semi bullying- mindless babble, nonsense as " chatter ".
 
Last edited:
How dare you refer to all this semi bullying- mindless babble, nonsense
" chatter ".

More accurately, some of it could be called "clucking"... seen less from a bunch of women at a Bunco party... 😬
 
I hear ya. I recently got a 2018 durango off my younger brother, fully loaded. Fucker flies, is quiet, has a fancy radio I can hook to my phone.

But, it doesn’t put the smile on my face as I get sideways with rolling burnouts with the blower screaming like a 747 is landing in the cab. Keep the car, cruise your daily. You’re still young and toys ain’t getting cheaper or easier to find.
Shit I can do that now with heated and cooled seats. I shoulda bought a V 10 years ago.
 
Back
Top