I found a bunch of gold! I'm rich!

Well, now what

  • Change the oil, run it a few more miles, check again

    Votes: 32 78.0%
  • Pull it apart.

    Votes: 9 22.0%

  • Total voters
    41
Equally bad given only ten minute idle vs 10 mile cruise
Well shit. I'm sorry to here that man. Before pulling it, I'd probably start disassembling periphial stuff in-car too see if anything obvious shows up. You'll be taking that stuff off anyways.

What a kick in the dick.
 
...just a non car guy opinion, but why take anything apart before you re-locate?
 
Oldest trick in the book! Dropped an intake valve head. I have only ever done that at an idle, and in literally one second max I had piston and aluminum rod chunks blowing out both headers. Aluminum chunks all through the motor, and even in the carbs.

Thrasher dropped a valve at the launch, under full throttle screw blown hemi power. Pretty sure Thrashers crew chief said the motor was OFF 59' into the run.......he still coasted the entire length of the track. Bangr and I were there when it happened. If my memory is correct, he still ran a 10.something 1/4 mile @ roughly 100mph......coasting from before the 60' timers. Big boy shit there......
Big boy shit there ranks right up there with @wickSS The skinny has two positions. Down or up. Mostly down!!

And its not weird that Captain John Force @Bangr was in the vicinity of both. :)
 
Big boy shit there ranks right up there with @wickSS The skinny has two positions. Down or up. Mostly down!!

And its not weird that Captain John Force @Bangr was in the vicinity of both. :)
Bangr indeed is a burnout artist, and he took to it like a duck does water. I have yet to see him let one get away from him, and the faster you are going, the harder burnouts are to keep under control.

Bangr was there for Thrashers fireworks that day. It was the FIRST time he ever was at a race in person with top end big boy pro mods running. After talking to Thrasher and crew for a bit, we went right to the 1/8th mile cones and sat down in the stands to watch a little bit. I tried telling Bangr that this was NOT gonna be like watching on TV, but he was having none of that. Well, wouldn't you know when they roll the promods around the corner for the first test hits, Thrasher is in the left lane. Lights flash, Thrasher comes by the 1/8th mile smooth as silk STILL riding on the back tires and finishes it off in style with a new MIR track record at the time with a 5.66 @ 259mph.......took 5 minutes for Bangr's lower jaw to return to the neutral position.:lmao:
 
Equally bad given only ten minute idle vs 10 mile cruise
Still not convinced. If the oil pressure is good, it’s not rattling just drive it. I’m sure whatever is clearancing itself still has some trash floating around. Or just send it down here, I’ll either blow it up proper or send it back running with a nice JY LS for ya
 
Still not convinced. If the oil pressure is good, it’s not rattling just drive it. I’m sure whatever is clearancing itself still has some trash floating around. Or just send it down here, I’ll either blow it up proper or send it back running with a nice JY LS for ya

I may have missed his response, but a couple of us have asked about his rockers and whether they could be the cause. I don't think I've seen a response to those posts.
 
I may have missed his response, but a couple of us have asked about his rockers and whether they could be the cause. I don't think I've seen a response to those posts.

Not the issue
 
Does it have a fuel pump eccentric on it I have seen the eccentric hit the timing cover if the timing chain doesn’t match the type eccentric that was used
 
it's brass flakes. We ran a top sportsman car all season after we wiped out the brass distributor gear. Something is rubbing on brass/bronze wrong. Brass/bronze is soft you're gonna need new oil pump, bearings and a hot tank. Prolly wiped out cam, rod and main bearings anyway. Maybe the lifters are bushed out. Run it
 
Looking forward to hearing the details when they come out.

Lol not a big secret!

Pull shit out.
Transport shit.
Pull shit apart.
Diagnose shit.
Order necessary fixer shit.
Clean the shit out of the shit.
Machine and balance shit as necessary.
Put shit back together.
Transport shit.
Put shit back into green shit.
Break shit in.
Break some other shit.
Sell the shit.
 
Fox,you running a bronze dist gear? I missed the answer in all this BS.

If yes,who installed it? It's critical to get it right.

Composite as suggested by comp (on several occasions) and a well respected ford builder
 
Lol not a big secret!

Pull shit out.
Transport shit.
Pull shit apart.
Diagnose shit.
Order necessary fixer shit.
Clean the shit out of the shit.
Machine and balance shit as necessary.
Put shit back together.
Transport shit.
Put shit back into green shit.
Break shit in.
Break some other shit.
Sell the shit.
And now we're all up speed.
 
Back
Top