I found a bunch of gold! I'm rich!

Well, now what

  • Change the oil, run it a few more miles, check again

    Votes: 32 78.0%
  • Pull it apart.

    Votes: 9 22.0%

  • Total voters
    41
So have I. That's what die grinders are for.
I don't think this qualifies as a factory "motor".

Next up- Painting inside engine block with Glyptal. Yes or no. ;)
You just made my lower region tingle.......
 
Holy shit I cant read through all this... Need a summary of whats been checked...

#1 Someone suggested early on to check the crank end play. Should be simple enough, just measure from however far out you can pry the balancer to however far you can shove it back in. Being a stick shift, it could have been riding the pressure plate without noticing if something is fucked with the linkage or hydraulics, as it hasnt made a decent pull yet. if it had loads of pressure on the crank, squishing the oil film on a basically dry startup, it might have delaminated the thrust at the beginninng.

#2 Being a Ford 🌈, It could be eating the copper cam thrust plate behind the cam gear, If the camgear has has some machining flash on the back it could be shaving down the thrust plate. Some smallblocks have them, some dont, but all the BB's do.

Shit happens.

I have never seen this amount of copper in anything unless something is seriously fucked.

I'm with Larry on this...


Good luck GreenFox, all the shitstorm gets better when you get this figured out and fixed.
 
Anyways.

Car immediately fired right up. Makes me so happy that you turn the fuel pump on, two pumps, and she lights up no hesitation. I love this car. I fucking love this car.

Water pump on at 120. Oil pressure 60psi.

Idled about 10 minutes. Temp up to 180. Fan kicked on. Oil pressure 57psi.

Valve train sounded the same as it did the other day. Again, nothing for me to compare it to so I don't know what is normal
Sounds promising, but not out of the woods yet. If you just drained the oil today, what did the oil out of the pan look like?

My painter said that I'd have paint anxiety with my car, nope, not yet. With having damn near everything off and back on, I've still got mechanical anxiety.

Just keep an ear out and hopefully all is well. Fingers crossed for you.
 
should have left the wife there with the new owner and taken the car with you.
Hind sight is always 20/20.
If she told me she was leaving, I would have kept that house with the nice yard and garage and sold the house i'm in now.
I honestly think she did it on purpose to see me have to get rid of all my stuff.
 
Holy shit I cant read through all this... Need a summary of whats been checked...

#1 Someone suggested early on to check the crank end play. Should be simple enough, just measure from however far out you can pry the balancer to however far you can shove it back in. Being a stick shift, it could have been riding the pressure plate without noticing if something is fucked with the linkage or hydraulics, as it hasnt made a decent pull yet. if it had loads of pressure on the crank, squishing the oil film on a basically dry startup, it might have delaminated the thrust at the beginninng.

#2 Being a Ford 🌈, It could be eating the copper cam thrust plate behind the cam gear, If the camgear has has some machining flash on the back it could be shaving down the thrust plate. Some smallblocks have them, some dont, but all the BB's do.

Shit happens.

I have never seen this amount of copper in anything unless something is seriously fucked.

I'm with Larry on this...


Good luck GreenFox, all the shitstorm gets better when you get this figured out and fixed.

Well on your #2 subject, this cam is a retrofit for non Hydraulic roller blocks. So the cam button (I think that's what is called) could potentially be the culprit.

@kilowattkid the oil in the pan was glittery as well, albeit less than the dumped filter
 
If she told me she was leaving, I would have kept that house with the nice yard and garage and sold the house i'm in now.
I honestly think she did it on purpose to see me have to get rid of all my stuff.
sorry man,that sucks all the way around.
 
Anyways.

Car immediately fired right up. Makes me so happy that you turn the fuel pump on, two pumps, and she lights up no hesitation. I love this car. I fucking love this car.

Water pump on at 120. Oil pressure 60psi.

Idled about 10 minutes. Temp up to 180. Fan kicked on. Oil pressure 57psi.

Valve train sounded the same as it did the other day. Again, nothing for me to compare it to so I don't know what is normal

Did you take it out and drive it for a few miles? If not, go drive it.

And put a working PCV system on it.
 
Ok fox, question.
If this is a non roller block with retrofit hydraulic roller kit.
Is it the type that uses the dog bone lifter bars and Spider type hold down spring?

If so?
Who drilled and tapped the bolt holes for the spider spring bar?
 
No spider thing. Not that dog bone stuff.
 
I hate to see the quit in you so strong. I gave you the name/number of a very good ford builder out of North Collins (not far from your car sits), and I'll guarantee that you never even used the number, which cost nothing.
<--- one of those non-car owning voices
 
I hate to see the quit in you so strong. I gave you the name/number of a very good ford builder out of North Collins (not far from your car sits), and I'll guarantee that you never even used the number, which cost nothing.
<--- one of those non-car owning voices

Unless the guy works for free, no sense calling.

Unless he accepts diamonds as a trade
 
Eeyore said "no sense in putting it back on, it'll only come off again".
No, he doesn't work for free....at all, but it could start a dialogue.
I'll go back to the non-car guy now.
 
Back
Top