I found a bunch of gold! I'm rich!

Well, now what

  • Change the oil, run it a few more miles, check again

    Votes: 32 78.0%
  • Pull it apart.

    Votes: 9 22.0%

  • Total voters
    41
It's comp cams 10w30 break in oil. I don't see how that would cause a leak but I'll entertain the thought

I have vent on each valve cover.

I don't know about crank case vacuum. If it's not something different than what I read on the vacuum gauge, I have about 18 in/hg at idle

Crank case vacuum, not what you read at the base of your carburetor. Do you have a functioning pcv valve or a vacuum pump? if not, that could be the reason you have an oil leak.
 
I know his next question is going to be, PCV system or vacuum pump what is that? someone have a pic of either one to post up, I have the pump and can post a pic later.
 
I know his next question is going to be, PCV system or vacuum pump what is that? someone have a pic of either one to post up, I have the pump and can post a pic later.

Fox, it's just a hose that runs from a valve cover breather to a vacuum source at the carb or manifold. If all you have are vents on the valve covers, you have no PCV system.
 
Anyways.

Car immediately fired right up. Makes me so happy that you turn the fuel pump on, two pumps, and she lights up no hesitation. I love this car. I fucking love this car.

Water pump on at 120. Oil pressure 60psi.

Idled about 10 minutes. Temp up to 180. Fan kicked on. Oil pressure 57psi.

Valve train sounded the same as it did the other day. Again, nothing for me to compare it to so I don't know what is normal
 
It's comp cams 10w30 break in oil. I don't see how that would cause a leak but I'll entertain the thought

I have vent on each valve cover.

I don't know about crank case vacuum. If it's not something different than what I read on the vacuum gauge, I have about 18 in/hg at idle
Damn!! I wish I had 1/4 of that vacuum at idle! Hahaha.

I guess a .700 lift cam with some duration and a short lobe separation don’t allow that into the equation though!!!!
 
Anyways.

Car immediately fired right up. Makes me so happy that you turn the fuel pump on, two pumps, and she lights up no hesitation. I love this car. I fucking love this car.

Water pump on at 120. Oil pressure 60psi.

Idled about 10 minutes. Temp up to 180. Fan kicked on. Oil pressure 57psi.

Valve train sounded the same as it did the other day. Again, nothing for me to compare it to so I don't know what is normal
Drive it again.
 
Valve train sounded the same as it did the other day. Again, nothing for me to compare it to so I don't know what is normal
Cam or lifters should have come with an adjustment procedure… can’t comment on how to adjust them without more info about what cam and lifters you are running… but basically all hydraulic lifters must be “centered” or preloaded in the bore to operate properly…

Chevy lifters, you back them off till it chatters, then tighten till it stops chattering and then half to three quarters turn more while idling…

… or you can go thru the firing order procedure cold and take up the slack and preload certain valves, roll the motor 180 degrees and adjust the remaining valves. This makes sure the lifters are on the base circle of the lobes… I prefer this method and it’s never missed being spot on.. and a lot less messy.
 
Cam or lifters should have come with an adjustment procedure… can’t comment on how to adjust them without more info about what cam and lifters you are running… but basically all hydraulic lifters must be “centered” or preloaded in the bore to operate properly…

Chevy lifters, you back them off till it chatters, then tighten till it stops chattering and then half to three quarters turn more while idling…

… or you can go thru the firing order procedure cold and take up the slack and preload certain valves, roll the motor 180 degrees and adjust the remaining valves. This makes sure the lifters are on the base circle of the lobes… I prefer this method and it’s never missed being spot on.. and a lot less messy.

I followed comp cams instructions exactly. They should be adjusted 100% accurately. I don't believe they are an issue
 


I had both valve covers ran to the headers and mine smoked something fierce during the cam break in. Switched to a pcv in one side and the other ran to my air cleaner/scoop, no more smoke.
I once put dual pcv valves on a sbc just for grins… it sucked so hard you could hear air sucking past the front seal when I shut the motor off…

Poor man’s vacuum pump… 🤣
 
Thanks, just took a quick look and did not see the meat relish, I was getting that 30 years ago, not sure why it was discontinued. My cousin from Anaheim was a glass blower there for quite a number of years and was will known, my Mom was from Bakersfield born of immigrant Irish people
who left Ireland.
 
Also, the bits of aluminum I found in the filter are likely from around the head bolts. Why wouldn't this be cleaned up? What the cock sucking fuck is this shit




I'm the guy who paid $8,800 for a set of custom compounds, then disassembled both and went to work with die grinders, porting grinders, regular grinders ect- and when I was finally happy after an untold amount of hours invested- sent pieces off to get thermal barrier coated. That is not even talking about the self fabbed hot pipe, cold pipe and exhaust down pipe. Which also got the same treatment- then sent out for thermal coating.


You want stress- talk to me when you hand over those parts that you packed into boxes and handed to ups to ship.

Drop the oil, pop off both valve covers for inspection of the bronze valve guides, I would also pull the distributor and inspect the gear for wear.

It's a glorified air pump for fucks sake.

If it were me- I would dump down some clean diesel atop both cylinder heads, the diesel will clean and still have somewhat lubricity.

You could be jumping the fence here.

New filter, 1 gallon (use less) diesel, new oil.


And run it.
 
Shit around those head bolts should have been milled flat.
I think it's all normal break-in shit. Run it.
 
Shit around those head bolts should have been milled flat.
I think it's all normal break-in shit. Run it.
So you have never seen bad casting flash even on factory built motors? Lol.
 
If I'm paying some to machine the engine & prep heads- I better not see any of that shit. If I bought stock heads- they would get cleaned up. That's just half ass.
Agreed. But I have seen some really bad casting flash left behind on factory motors. Both on gassers from the big 3, to big truck diesel engines- take your pick.
 
Back
Top