Breaking up at high rpm, carb issues, and converter issues.

Seriously, as stated, this thread is full of knowledge for guys like me. Might seem like basic stuff to the seasoned and weathered ones around here..
I agree. My plugs will never look like those do.
I'm just trying to find a happy medium between puffing black smoke, and leaning it out !
 
So based on what ive read here, can you read plugs AT ALL if it's not simply wot shutdown and check?

Carbureted street car for instance, can i pull a plug after 500 miles of any kind of driving and see wtf is going on in the cylinders?
 
Wise decision to get a crank trigger on it. It’s crazy how much the timing fluctuates without one.
I actually had a distributor once cause a issue similar to yours. It had a random miss not at any particular point though. Put it on a scope and t looked crazy erratic. Changed the distributor and she was a happy motor…er um I mean engine. :ROFLMAO:
What I don’t get is, if the ignition box is what is retarding the timing as seen in that video, how is a crank trigger going to help that aspect?

I understand it will give rock solid timing, but won’t the box still do what it does?
 
Last edited:
So based on what ive read here, can you read plugs AT ALL if it's not simply wot shutdown and check?

Carbureted street car for instance, can i pull a plug after 500 miles of any kind of driving and see wtf is going on in the cylinders?
I found this online a while ago, but I think we are talking about two different types of plug reading. We are talking strictly WOT here.

Edit: “here” meaning in this thread, not sure if this pic is accurate to use for what you are asking.
 
Last edited:
Also, why does he say it’s at 10, when it looks like 5? Both directions 10 is in the same place. 🤷🏻‍♂️

Crankshaft degrees are 2 times distributor degrees shown on the distributor machine.
Thanks for pointing this out, that went over my head when I read it.
 
most modern boxes have the inductive delay somewhat built it. 7530T, Grid, etc, so that when used with a crank trigger you will get little to no retard with rpm.
Ive checked up to about 7000 with a bracket engine, and had virtually no retard.
The EFI stuff has inductive delay settings and ive stood next to a 500 at over 10k, setting it to make sure i had the same timing from 2500 to 10,000
you havent lived until you have your head next to a 500 at 10k
Distributors are awful as far as retarding timing goes, especially with a chain driving the cam
Get a crank trigger, and a more modern box
hell even a msd2 with a trigger is decent
 
most modern boxes have the inductive delay somewhat built it. 7530T, Grid, etc, so that when used with a crank trigger you will get little to no retard with rpm.
Ive checked up to about 7000 with a bracket engine, and had virtually no retard.
The EFI stuff has inductive delay settings and ive stood next to a 500 at over 10k, setting it to make sure i had the same timing from 2500 to 10,000
you havent lived until you have your head next to a 500 at 10k
Distributors are awful as far as retarding timing goes, especially with a chain driving the cam
Get a crank trigger, and a more modern box
hell even a msd2 with a trigger is decent
I just spent good money on this brand new MSD7AL-2. Are you telling me it’s no bueno? 🤦🏻‍♂️
 
Years ago a friend had an engine built and a magazine did an article on it. One of the things they wanted us to do was run it on a dyno and compare carbs to EFI. So I got the tuning duties on the EFI. This was an ancient Accel Gen 6 system, no wideband feedback. Did this at Nickersons in PA.
Well, I could not get the EFI to match the power of the carb, was down a solid 10hp throughout the entire pull.
But, at the track the EFI was consistently quicker and faster, go figure.........

One thing I found on the dyno was exactly what you are discussing here, timing retarding as the rpms climbed. We were losing 4* at 8500. Yeah, I stood there with the timing light as Dean made the pull, that was VERY nerve-racking!

With the EFI I was able to adjust the curve so the timing stayed consistent through the pull.

And guess what: No difference in power! That was very surprising to all of us. Made me wonder if the timing was actually moving or if it was the timing light giving us false info.

I had a Holley 60-2 trigger wheel on my engine many years ago. When you check the timing on that setup it doesn't look like the engine is actually running, the line does not move! Rev it to any rpm, it did not move. But it made no more power than a normal distributor feeding the EFI which then fired the MSD 6AL box, but boy did it look nice!
 
What I don’t get is, if the ignition box is what is retarding the timing as seen in that video, how is a crank trigger going to help that aspect?

I understand it will give Rick solid timing, but won’t the box still do what it does?
Please forgive me I have not read and kept up with your entire thread. You have way more help than I can offer already. But I do know what a crank trigger can do for you vs a distributor.

That being said look at it like this, if your distributor is already say fluctuating 2 degrees on its own. And then you have a box that you only want 2 degrees pulled, with your setup you potentially have 4 degrees coming out randomly or maybe zero since its not steady. That is saying everything else is doing its job ie no slack timing chain, distributor gear flex, etc. etc..

With a crank trigger you remove the erratic and I do mean erratic nature of a distributor. So now when the box pulls 2 its typically 2 not 2 sometimes.

I really like the reaction when a guy who has been satisfied with a MSD distributor thinking he has steady timing puts a light on it watches the movement then puts a crank trigger on it and its night and day. This is the reason everything has gone to some form of a crank sensor automotive wise speaking. You can literally see the difference its moving that much.
 
Todays epiphany…..last night while bumping timing I noticed that giving it about 2000-3000 rpm caused the timing to retard 2*.

I’m going to pull the distributor tomorrow and look at the wear. I already ordered a new gear just in case. Thinking about switching to a crank trigger this winter.

Liking the idea of the crank trigger.

Also, like others have mentioned, lot's of good discussion and knowledge to be learned here, and other threads like this one. Without throwing darts at the blue oval, which I am guilty of regularly, the hot rod in this case is clearly a stout running machine, and issues that I would normally not consider due to ignorance of the Ford design could be a cause. I would never think for a minute that my distributor gear was wearing in a chevy. Learning new stuff is ALWAYS a bonus!

As far as the 2 degree retard goes......if your timing is sitting where you made the last move and nothing picked up, but nothing slowed down, a 2 degree retard is not likely to be easily measured by time slips.

When trying to seek every ounce of potential from a drag car, it is really tough, and maybe even impossible without a ton of data acquisition.

I have tried both ways, and it sure makes things clear in a hurry when you spend yourself into a headache with grids, and a pile of racepak stuff.

Before having that stuff, I would simply play with jetting, timing, and an occasional plug check, and all of my decisions were made from my only source of data......a timeslip. Max ET was the goal, let the MPH land where it may, and as long as it repeated consistently, I would give the old girl new plugs every spring.....just because. When I got the coupe, we trial and errored that thing until the cows came home. It was fast, but inconsistent much of the time. I finally opened up the wallet and went to a grid, racepak, and top end shocks, with shock sensors. The journey got boring in a hurry after that. It took maybe two limited run trips to the track for me and Bangr to pin the setup down.

Granted, your ponycar is not in the same ET range as my junker, but considering it is a smallblock, small tire car, that thing is hauling ass. You have enough power to make it finicky.

I have no doubt you will get this thing lined out PR, due to your willingness to make it happen. Just keep this in mind......if you had a .75 to 1 second to the 1/8 slower car, most of the issues you are dealing with would not be there. From my personal experience, you have crossed the power/ET line that makes issues appear because the entire package is not 100% perfect. With 100 less horsepower, the inconsistent wheel speed at the line would vanish. At slower ET's, a dead hook is normal and perfectly fine.

This stuff can be mentally exhausting, but once in a while you have to back up and objectively assess just how far you have come recently. You are doing GREAT! Keep making educated decisions on changes, and don't let a lack of immediate returns get you down. You are really close to the max potential with the current package, it is jut a matter of making it work more regularly.
 
I just spent good money on this brand new MSD7AL-2. Are you telling me it’s no bueno? 🤦🏻‍♂️
na, it should be fine
i just prefer the digital stuff

that being said, get a crank trigger. its less frustrating...lol
even the factories use their version of a crank trigger
 
Liking the idea of the crank trigger.

Also, like others have mentioned, lot's of good discussion and knowledge to be learned here, and other threads like this one. Without throwing darts at the blue oval, which I am guilty of regularly, the hot rod in this case is clearly a stout running machine, and issues that I would normally not consider due to ignorance of the Ford design could be a cause. I would never think for a minute that my distributor gear was wearing in a chevy. Learning new stuff is ALWAYS a bonus!

As far as the 2 degree retard goes......if your timing is sitting where you made the last move and nothing picked up, but nothing slowed down, a 2 degree retard is not likely to be easily measured by time slips.

When trying to seek every ounce of potential from a drag car, it is really tough, and maybe even impossible without a ton of data acquisition.

I have tried both ways, and it sure makes things clear in a hurry when you spend yourself into a headache with grids, and a pile of racepak stuff.

Before having that stuff, I would simply play with jetting, timing, and an occasional plug check, and all of my decisions were made from my only source of data......a timeslip. Max ET was the goal, let the MPH land where it may, and as long as it repeated consistently, I would give the old girl new plugs every spring.....just because. When I got the coupe, we trial and errored that thing until the cows came home. It was fast, but inconsistent much of the time. I finally opened up the wallet and went to a grid, racepak, and top end shocks, with shock sensors. The journey got boring in a hurry after that. It took maybe two limited run trips to the track for me and Bangr to pin the setup down.

Granted, your ponycar is not in the same ET range as my junker, but considering it is a smallblock, small tire car, that thing is hauling ass. You have enough power to make it finicky.

I have no doubt you will get this thing lined out PR, due to your willingness to make it happen. Just keep this in mind......if you had a .75 to 1 second to the 1/8 slower car, most of the issues you are dealing with would not be there. From my personal experience, you have crossed the power/ET line that makes issues appear because the entire package is not 100% perfect. With 100 less horsepower, the inconsistent wheel speed at the line would vanish. At slower ET's, a dead hook is normal and perfectly fine.

This stuff can be mentally exhausting, but once in a while you have to back up and objectively assess just how far you have come recently. You are doing GREAT! Keep making educated decisions on changes, and don't let a lack of immediate returns get you down. You are really close to the max potential with the current package, it is jut a matter of making it work more regularly.
Thanks for all of what was said here and I appreciate all of the help and wisdom, you and others have provided. I would not be this far along without you guys.

Cannot be said enough. You can make yourself hate the game if you let it.
Yes, as you said and as Mitch alluded to, this is where I’m at. I have a car running “good” and faster than I’ve ever been, but I’m banging my head against the wall right now.

I went from going faster week after week to losing 2mph and a tenth or two in e.t. For no obvious reason. Because I hit a 5.80 it has me chasing the 5.79 and I’ve become obsessed.
 
Looking at this one.

 
Looking at this one.

do some looking. im not sure the non digital boxed are able to use the 12 magnet wheels?
 
do some looking. im not sure the non digital boxed are able to use the 12 magnet wheels?
There is a 4 magnet also.

 
There is a 4 magnet also.

everyone is always concerned with more magnets equaling more accurate and precise control
A/B/A test on dyno with a 500 between the 4 mag and a 36-1 was nothing measurable power wise
Im sure with in cylinder combustion analysis a person may be able to find something? But i didnt see it
My ls i went from 58x to 12-1
again, i saw nothing, except the 58X would shut off above about 8800 rpm due to the sensor being a cunt...lol
 
everyone is always concerned with more magnets equaling more accurate and precise control
A/B/A test on dyno with a 500 between the 4 mag and a 36-1 was nothing measurable power wise
Im sure with in cylinder combustion analysis a person may be able to find something? But i didnt see it
My ls i went from 58x to 12-1
again, i saw nothing, except the 58X would shut off above about 8800 rpm due to the sensor being a cunt...lol
Thanks for the info! My only issue might be that my alternator tensioner uses the lower timing cover bolt, so I see some fabrication in my future.
 
Liking the idea of the crank trigger.

Also, like others have mentioned, lot's of good discussion and knowledge to be learned here, and other threads like this one. Without throwing darts at the blue oval, which I am guilty of regularly, the hot rod in this case is clearly a stout running machine, and issues that I would normally not consider due to ignorance of the Ford design could be a cause. I would never think for a minute that my distributor gear was wearing in a chevy. Learning new stuff is ALWAYS a bonus!

As far as the 2 degree retard goes......if your timing is sitting where you made the last move and nothing picked up, but nothing slowed down, a 2 degree retard is not likely to be easily measured by time slips.

When trying to seek every ounce of potential from a drag car, it is really tough, and maybe even impossible without a ton of data acquisition.

I have tried both ways, and it sure makes things clear in a hurry when you spend yourself into a headache with grids, and a pile of racepak stuff.

Before having that stuff, I would simply play with jetting, timing, and an occasional plug check, and all of my decisions were made from my only source of data......a timeslip. Max ET was the goal, let the MPH land where it may, and as long as it repeated consistently, I would give the old girl new plugs every spring.....just because. When I got the coupe, we trial and errored that thing until the cows came home. It was fast, but inconsistent much of the time. I finally opened up the wallet and went to a grid, racepak, and top end shocks, with shock sensors. The journey got boring in a hurry after that. It took maybe two limited run trips to the track for me and Bangr to pin the setup down.

Granted, your ponycar is not in the same ET range as my junker, but considering it is a smallblock, small tire car, that thing is hauling ass. You have enough power to make it finicky.

I have no doubt you will get this thing lined out PR, due to your willingness to make it happen. Just keep this in mind......if you had a .75 to 1 second to the 1/8 slower car, most of the issues you are dealing with would not be there. From my personal experience, you have crossed the power/ET line that makes issues appear because the entire package is not 100% perfect. With 100 less horsepower, the inconsistent wheel speed at the line would vanish. At slower ET's, a dead hook is normal and perfectly fine.

This stuff can be mentally exhausting, but once in a while you have to back up and objectively assess just how far you have come recently. You are doing GREAT! Keep making educated decisions on changes, and don't let a lack of immediate returns get you down. You are really close to the max potential with the current package, it is jut a matter of making it work more regularly.

If I could like this 100 times I would.

I’d have to ask what the goal is at this point.

It’s so easy to chase et & hero runs but barring chances of hurting it & unless the goal is to outrun everything on the property, some of this stuff is moot & heads toward paralysis by analysis.

The car is absolutely hauling ass & PR should be proud of it but are we trying to win bracket races, be a tnt guy… what?

Printing tickets is a LOT different than going fast IMO
 
If I could like this 100 times I would.

I’d have to ask what the goal is at this point.

It’s so easy to chase et & hero runs but barring chances of hurting it & unless the goal is to outrun everything on the property, some of this stuff is moot & heads toward paralysis by analysis.

The car is absolutely hauling ass & PR should be proud of it but are we trying to win bracket races, be a tnt guy… what?

Printing tickets is a LOT different than going fast IMO
I kind of explained it in post #521. I’m caught up chasing 5.79 right now. I got a late start to the season due to getting screwed by an engine shop, so the car is pretty dialed in right now other than losing the 2mph and tenth or two.

I’m entering the last big bracket next weekend and then it’s TnT for the rest of the year. I probably won’t do well since I have not focused an ounce of effort towards my reaction times.

My whole life I’ve always just chased the best possible e.t. That I could get with my particular combo. I’m caught up in that right now. I keep telling myself that if I could hit that 5.79, I can focus my attention on other stuff.

To your point, I lost how relatively consistent the car is. It’s not duplicating slip after slip, but even while making changes it’s pretty consistent. Case and point here are all my passes while making changes Friday…

1. 5.920@115.71
2. 5.895@116.92
3. 5.917@116.84
4. 5.916@116.10
5. 5.892@116.46
 
Back
Top