Breaking up at high rpm, carb issues, and converter issues.

The last two ^ look a lot better than previous plug pictures.

Is the ceramic shiny at all at the tip where it transitions from the vertical side of the ceramic to the tip radius around the electrode?

Study the center electrode of a new (unused) plug. At the bottom of the V groove on the end of the groove under the side electrode I think you will see a tiny burr that was formed when the groove was cut or ground (however it is made), similar to what forms on the lower edge of a piece of steel when you grind it with a bench grinder, but just a tiny burr outside the end of the bottom of the groove.

If that burr was on the plug before it was run and is gone after the pass, the plug is too hot, there is too much advance or the A/F is lean, or some combination of the three causing too much heat.

I consider the little burr as the canary in the coal mine and expected to see it intact on all 8 plugs in a 13.8/1 SBC after Friday night follies in a 100 lap main on a 1/2 mile asphalt track. Iron BowTie head, #9 heat range.

When the heat range and tuneup are both right there will not be enough free oxygen from being too lean to erode it away and plug the tip will not get hot enough to melt the burr off the electrode.
 
Itey, I have not read that whole post yet.

Long ass day. Just got home. I made some good progress with the suspension, but I’ve gone backwards on mph and e.t. and I don’t understand why.

I was running consistent low 5.80’s @ 118. Now I can’t seem to get the car to run over 116.

I watched a video of my 3rd run that my buddy took and I could see the car wasn’t on the tire long enough. I clicked the compression up 3 clicks on the rear shocks and the next pass shattered my best 60’ and went 1.25. However, I was not rewarded on the big end. Car felt strong the whole way, but only managed a meager 5.91 @ 116.10.

Next pass was an abort, they fucked me at the starting line. Final pass, I cut another decent 1.28 60’, but again only 5.89 @ 116.46.

I don’t understand where I lost the 2mph. I’m guessing it is tune related. I just don’t get how you pick up that much in the 60’, but don’t see it on the big end.
 
Did you run colder plugs than previous best ET/mph?
Yes. Bumped timing 2* after first 3 passes, no change in mph. Added 4 jet sizes front and rear for the last run, no change in mph.
 
Weather ? Barometric pressure and humidity ?
 
If i just had to make a wild guess you've picked up 60ft from susp and tire change but lost some top end HP from the plug swap. Where they same brand/type plugs? I always had best results with v-groove NGKs
I lost the mph before suspension change, tire change, and plug swap. Then I tried autolite AR3935’s, which are equivalent to NGK7’s.

Last night was the first night with NGK 8’s. I went to the 8’s because I thought that I might be getting some pre ignition on the top end, but I found out last night it was the piece of shit 7800 chip.
 
this is the last pass of the night. I realized that my alternator wasn’t putting out. Couldn’t start the car in staging until I turned off the water/fan, and lights.

This is after going from .092/.104 jets to .096/.108. Logic was, DA was going down and previous pass blipped 13.0-13.2 on the wideband. I wanted to see if it wanted more fuel since I bumped timing earlier.

AFR was good at mid to high 12’s throughout the run. Got back to the pits and realized that the bottom bolt that tensions the alternator broke and I lost my belt. Must have lost it on the previous pass.

 
It has always been my personal experience that on the fuel end........rich makes more MPH, lean makes quicker ET with less MPH. Obviously we are talking a little fat, or a little lean.
 
It has always been my personal experience that on the fuel end........rich makes more MPH, lean makes quicker ET with less MPH. Obviously we are talking a little fat, or a little lean.
Last night hitting 13’s and still lower mph and e.t.

Could this be transmission or converter related?
 
SBF's have hot cylinders, I believe all four corners are that way. When people run a decent amount of nitrous through them they typically use an MSD Grid and the cylinder pickup so they can remove timing on those cylinders. For those not having a way to modify timing (and fuel) on a cylinder by cylinder basis they spend a decent amount of money with an engine builder who will modify the intake manifold to get all the cylinders running the same. This is done with an engine dyno with (in your case) 8 individual wideband sensors. With EFI this is easy for me to fix.

What fuel are you running? Post a picture of the straps on the NGK plugs. Can't read the cut-back Autolites the same.

My best 60ft did not give me my best ET so I wouldn't worry so much about that.
 
SBF's have hot cylinders, I believe all four corners are that way. When people run a decent amount of nitrous through them they typically use an MSD Grid and the cylinder pickup so they can remove timing on those cylinders. For those not having a way to modify timing (and fuel) on a cylinder by cylinder basis they spend a decent amount of money with an engine builder who will modify the intake manifold to get all the cylinders running the same. This is done with an engine dyno with (in your case) 8 individual wideband sensors. With EFI this is easy for me to fix.

What fuel are you running? Post a picture of the straps on the NGK plugs. Can't read the cut-back Autolites the same.

My best 60ft did not give me my best ET so I wouldn't worry so much about that.
I’m not worried so much about best 60’ giving me best e.t. As you said, my best e.t. 5.80 @ 118.89 wasn’t my best 60’. I attribute that to wheel speed.

My bigger concern is losing 2 mph when due to weather car should be picking up, not slowing down. Out helping my parents remove a pier at their camp ground. Will post pics of straps later.

However, I did see the color change on the strap, which is why I added 2* of timing. It was more towards the tip than the bend.
 
Todays epiphany…..last night while bumping timing I noticed that giving it about 2000-3000 rpm caused the timing to retard 2*.

I’m going to pull the distributor tomorrow and look at the wear. I already ordered a new gear just in case. Thinking about switching to a crank trigger this winter.
 
Todays epiphany…..last night while bumping timing I noticed that giving it about 2000-3000 rpm caused the timing to retard 2*.

I’m going to pull the distributor tomorrow and look at the wear. I already ordered a new gear just in case. Thinking about switching to a crank trigger this winter.

Here is a video showing the electronic slew rate retard characteristic of all analog ignition amplifiers, induction or CD. Crankshaft degrees are 2 times distributor degrees shown on the distributor machine.

Some new "digital microprocessor controlled" amplifiers have a microprocessor calculator that compensates for the slew rate time lag. They do this by delaying (retarding) the firing point from the trigger point at low RPM and gradually reducing the time delay as RPM increases at a rate that keeps the spark firing at the same crankshaft degree at all RPM (just like points ignition, LOL).

The microprocessor controlled MSD 6530 Programmable 6AL is used with a locked distributor or crank trigger and programmed with advance curves like you would have with weights and springs, like the timing tables in a EFI ECU controller.

 
Here is a video showing the electronic slew rate retard characteristic of all analog ignition amplifiers, induction or CD. Crankshaft degrees are 2 times distributor degrees shown on the distributor machine.

Some new "digital microprocessor controlled" amplifiers have a microprocessor calculator that compensates for the slew rate time lag. They do this by delaying (retarding) the firing point from the trigger point at low RPM and gradually reducing the time delay as RPM increases at a rate that keeps the spark firing at the same crankshaft degree at all RPM (just like points ignition, LOL).

The microprocessor controlled MSD 6530 Programmable 6AL is used with a locked distributor or crank trigger and programmed with advance curves like you would have with weights and springs, like the timing tables in a EFI ECU controller.

WTF, so how does giving it advance stop it from retarding? So if I put the weights, springs, and donut back in, it isn’t going to retard the timing?

Why wouldn’t it?
 
Present!

Oh, sorry.. i heard retarded and thought y'all were talking about me.

seriously, as stated this thread is full of knowledge for guys like me. Might seem like basic stuff to the seasoned and weathered ones around here..

Free bump anyway
 
Also, why does he say it’s at 10, when it looks like 5? Both directions 10 is in the same place. 🤷🏻‍♂️
 
Here’s another thing about that video that has me scratching my head. In theory, it wouldn’t even matter if you had a crank trigger because the box is retarding the timing. 🤔
 
Wise decision to get a crank trigger on it. It’s crazy how much the timing fluctuates without one.
I actually had a distributor once cause a issue similar to yours. It had a random miss not at any particular point though. Put it on a scope and it looked crazy erratic. Changed the distributor and she was a happy motor…er um I mean engine. :ROFLMAO:
 
Last edited:
Back
Top