Breaking up at high rpm, carb issues, and converter issues.

Not sure if I posted this somewhere before, here is a typical 10.00 pass from my car. It does this each and every time, and does the same thing when running it unrestricted going 9.40, except the stall is higher without the plate in there.

i98nlAX.jpg
 
Don't worry about the rpm drop after the hit, mine does the same exact thing and it runs perfect. I have seen this on a few other cars, doesn't seem to be an issue. My car dead hooks every time.
everything with a converter does as a rule. The converter flashes up then starts trying to couple and it pulls it back. 500 rpm is a bit much, but that all has to do with the voodoo that goes on in a converter, and i leave that up to adam at A1...lol. This is a pic of a graph from my roadster and you can see it tug it back some. I took the pic for the down track tire spin/shake that was stupid of me to drive through (1/8 mile)

 
everything with a converter does as a rule. The converter flashes up then starts trying to couple and it pulls it back. 500 rpm is a bit much, but that all has to do with the voodoo that goes on in a converter, and i leave that up to adam at A1...lol. This is a pic of a graph from my roadster and you can see it tug it back some. I took the pic for the down track tire spin/shake that was stupid of me to drive through (1/8 mile)

That looks like a chassis dyno pull with tires too small, slipping-grabbing. I've seen too much spark advance = detonation do something similar to that.
 
That looks like a chassis dyno pull with tires too small, slipping-grabbing. I've seen too much spark advance = detonation do something similar to that.
some of those were 500 rpm spikes. I was having trouble even seeing from the 330 to the 1/8
that was stupid
but went 4.60 to the 1/8
 
Don't worry about the rpm drop after the hit, mine does the same exact thing and it runs perfect. I have seen this on a few other cars, doesn't seem to be an issue. My car dead hooks every time.
Still might be a touch too tight, so might not be worth sending back. I think if I swap to 4.30’s maybe it will be just right? Not sure how much it will change from what it’s doing now with the 4.71’s.

I ran a 9.42 @ 115 because I couldn’t make it to the end of the 1/4. That has me wanted to see what it can do if I could stay in it and cross the stripe.
 
Still might be a touch too tight, so might not be worth sending back. I think if I swap to 4.30’s maybe it will be just right? Not sure how much it will change from what it’s doing now with the 4.71’s.

I ran a 9.42 @ 115 because I couldn’t make it to the end of the 1/4. That has me wanted to see what it can do if I could stay in it and cross the stripe.
it will be slower to the 1/8 for sure with the .30's compared to the 4.71
my old roadster i went from 4.71's to 4.30s to bring the rpm down at the stripe (8200 with a 565) when i made it a 582.
35 more hp, went the same or slower in the 1/4 but brought the rpm down so i didnt care
 
Not sure if I posted this somewhere before, here is a typical 10.00 pass from my car. It does this each and every time, and does the same thing when running it unrestricted going 9.40, except the stall is higher without the plate in there.

i98nlAX.jpg
When the converter is in the stall condition the stator recovers energy by redirecting the fluid to cause more forward rotation of the pump. The recovered energy results in the torque multiplication.

I think the RPM drop is because as the turbine starts to rotate when the car speed increases the effect of the stator diminishes and not as much energy is recycled back into forward rotation of the pump (crankshaft).
 
it will be slower to the 1/8 for sure with the .30's compared to the 4.71
my old roadster i went from 4.71's to 4.30s to bring the rpm down at the stripe (8200 with a 565) when i made it a 582.
35 more hp, went the same or slower in the 1/4 but brought the rpm down so i didnt care
Won’t the converter flash slightly higher with the 4.30’s?
 
Won’t the converter flash slightly higher with the 4.30’s?
yes, but you lose overall leverage on the tire
converter flash is the 1rd 10' of the racetrack, after that its all leverage, and higher numerical gear has more torque multiplication
 
Probably.

I know it will stay on the converter longer & take longer to lock it up. Depending on your engine combo it might not hurt as bad as you’d think.
since he does hit the tire too hard, it will soften that taking leverage away
 
Probably.

I know it will stay on the converter longer & take longer to lock it up. Depending on your engine combo it might not hurt as bad as you’d think.
I started another thread a couple of days ago about the effects of the gear change and converter vs SLR. I already have a low SLR, like 8.48 and going to 4.30's will bring that down to 7.74. I was hoping the extra flash stall might balance that out, but doesn't seem so.
 
I started another thread a couple of days ago about the effects of the gear change and converter vs SLR. I already have a low SLR, like 8.48 and going to 4.30's will bring that down to 7.74. I was hoping the extra flash stall might balance that out, but doesn't seem so.
May not help the SLR, but it will help keep the front end down.
 
May not help the SLR, but it will help keep the front end down.
I haven't made one single adjustment on the rear shocks. I think I can slow that down. Now that the engine is close, I'll start messing with suspension. I might move my lower bar down 1/4 at the frame bracket and that will give me around 115% AS vs the current 129% it has. Then adjust the shocks after we see what is does.

I did go 2 clicks on the rebound on the fronts last Friday and that helped.
 
Back
Top