Leak down test after spewing water at the track

I'm thinking all you had wrong from the beginning was the #4 plug wire not connected properly .. and in all your diagnosing you messed something else up somewhere
Maybe, who knows.

The more research I do on intakes the more I think the CID will be too big. John doesn’t answer my texts or calls, I must have got lucky the first time I spoke to him.

I think he said that intake will be a 4.5” plenum volume. The Edelbrock Glidden intake is only 3.6”. 4.5 is fucking huge! I have a BLP on the way. Intake is easy to swap, so if it comes out and I think it will work, I’ll get it.

I’ll likely slap the BMP on as is and have it ported over the winter.
 
Last edited:
You could be worse off with a dominator plenum BMP intake over the 4150 BMP intake and your adapter, because of air velocity

The CID intake is on another planet. Even though the plenum volume is huge on paper, the intake just flat out works because it's almost a single tunnel ram. The air doesn't have to bend. I'm sure i've even seen the 4.5 on engines milder than yours working well.
If your engine is liking an 1150 dominator which it seems to be then i think it will gain even with the 4.5 CID intake. But the 4.0 plenum might be better. Did John confirm the first time he responded that they are making only a 4.5 for sure, for windsor heads? I'd just wait it out, i'm sure they will post some results

Remember that guy i mentioned on ls1tech gained a heap with a CID intake (et also not just dyno), and he has cathedral heads with intake adapters, his heads don't flow much more than yours do

Here's another example.. but with higher flowing heads, 430ci running only a 1050 dominator

828HP/610ft lbs..

The BMP 4150 and 4500 intakes are identical except for the top flange. Plenum volume is the same for both.

I am not opposed to buying the CID, but I need to hear from John that my car won’t turn into a dog. I’m keeping a lookout for it.
 
Yeah i get it. Years ago someone swapped from a MAST 4500 LS intake which was one of the best at the time, to a CID, and gained 50hp , yes 50hp . I can't find a link to it now but it was legit at the time

And have a look at the 4500 mast intake... https://www.baldwinengines.com/product/mast-motorsports-ls7-4500-flange-carb-intake/

When/if CID release a windsor head version, i'm sure several people are going to try one and post their results so just wait until that happens
I reached out to John on Instagram asking if I can be a test mule for one. He never responded. Their Instagram is pretty active, so I’m guessing he thinks I’m some groupie bitch and ignoring me. 😆
 
PAC 1225 Titanium Valve Spring Package
Jesel Sportsman 1.7 Shaft mount rockers
Manton 5/16 .118 wall pushrods

Why?
Just curious since you said the clearance had changed. My experience with shaft rocker systems is they do not move. You can unbolt them, put them back on, the lash is identical.

I use the tools from LSM for setting lash and checking spring pressure, really nice stuff, not cheap though. Before that I had issues getting consistent valve train adjustments, I was all over the place, kinda sucked at it. I use the go, no-go method and it is pretty much foolproof.
 
Just curious since you said the clearance had changed. My experience with shaft rocker systems is they do not move. You can unbolt them, put them back on, the lash is identical.

I use the tools from LSM for setting lash and checking spring pressure, really nice stuff, not cheap though. Before that I had issues getting consistent valve train adjustments, I was all over the place, kinda sucked at it. I use the go, no-go method and it is pretty much foolproof.
Yea, when I took them off I loosened them all up first. Then I realized that I should have got them on the base circle and unbolted the shafts. Too late I had to set them again.

I have the LSM tool as well.
 
Last edited:
I have the LSM tool as well.
Dammit there ya go again. I really cant believe you would blink at a $700 ARB when you have a $300 tool for setting valve lash. :ROFLMAO: I'm really jealous! I want one but I just cant force myself to buy one just yet. I've set valves for so long without one and not had any issues It would be more like just a extra I really don't need. But I do want.
 
Dammit there ya go again. I really cant believe you would blink at a $700 ARB when you have a $300 tool for setting valve lash. :ROFLMAO: I'm really jealous! I want one but I just cant force myself to buy one just yet. I've set valves for so long without one and not had any issues It would be more like just an extra I really don't need. But I do want.
The only thing not expensive about my car is the car itself. The shit bolted on it is a different story.😂
 
Dammit there ya go again. I really cant believe you would blink at a $700 ARB when you have a $300 tool for setting valve lash. :ROFLMAO: I'm really jealous! I want one but I just cant force myself to buy one just yet. I've set valves for so long without one and not had any issues It would be more like just a extra I really don't need. But I do want.
That tool is tits! I use it with normal polylocks too. When I kick-it I told my wife to give it to a good friend of mine. He loves it but doesn't want to pay for it. :) My son wouldn't know what to do with it. :(
 
Yea, when I took them off I loosened them all up first. Then I realized that I should have got them on the base circle and unbolted the shafts. Too late I had to set them again.

I have the LSM tool as well.
I turn the engine over by hand with no spark plugs to make it easy and loosen them on the base circle, makes things so darn easy.
 
The only thing not expensive about my car is the car itself. The shit bolted on it is a different story.😂
I understand how the car isnt worth the bolt ons. I was going to say it is a Ford Mustang. But after reading @Mike Beck post I thought maybe I would have a shot at you having your wife sending me yours when you head off to the pearly gates. 😇😂😂😂😂
 
I’ve had this Motion Raceworks engine diaper sitting in the garage for almost 2 years. I forgot to put it on when I had the engine out this year. Now that I have the lift it wasn’t too bad. I loosened the steering rack and fished it in between. It fits very nice.

Rear main is dripping, so I wanted to get this on, so I don’t have to worry about dripping on the track for me or anyone else. I’m happy with it. Probably 1 or 2 more test n tunes at most left. I’ll fix the rear main over winter.


IMG_7392.jpeg
 
Yeah i get it. Years ago someone swapped from a MAST 4500 LS intake which was one of the best at the time, to a CID, and gained 50hp , yes 50hp . I can't find a link to it now but it was legit at the time

And have a look at the 4500 mast intake... https://www.baldwinengines.com/product/mast-motorsports-ls7-4500-flange-carb-intake/

When/if CID release a windsor head version, i'm sure several people are going to try one and post their results so just wait until that happens
I finally got a hold of John today. I started asking him questions and he got irritated. I asked him how a 4.5 is gonna make power on a 427 with AFR 220’s when I’m only spinning it to 7500-7700.

I told him I’ve had friends with higher compression lose 2-3 tenths by going to a Glidden intake which is only 3.6 plenum. Then I asked him if he knows who Sam Vincent is and he said yes. I said Sam says the CHI 4.0 shines over 8000rpm.

He said you’re talking to too many people. Then he asked what intake I’m running now. I told him the BMP which he said is a CHI commander. I told him I was told it’s the 3.0 version and he said no, it’s 4.0, but he sounded unsure. He didn’t know that BMP cast theirs as all one piece instead of having a separate valley pan. The sad thing is that BMP doesn’t even know the plenum volume. WTF?

I said I’m not looking for a freebie, he yells no freebies! I said I just said I don’t want a freebie, I just want to test it. He said I’ve already tested it and the first one should be ready this week and if the casting is good they will start making them.

My thing is, what did he test it on? I don’t see how a 4.5 will work for me. Even talking to Eric Weingartner he said that a 4.0 CHI is too big for my heads. 🤷🏻‍♂️
 
With the money y'all motherfuckers have in here, you should have a 3, 3.5, 4, 4.5 and even a motherfuckin 5 on order!
Coming from a guy with a pristine 55 that was ProCharged and turbo charged and had the same big block built twice isn't that like 8,9,10, through 15. 😂
 
I just measured the ports on the BMP and it’s definitely a 4.0.

It’s tricky to get your hands and a tape in the plenum, but I got roughly 1.625” x 2.5” =4.0625”

Too close to 4.0 to be a 3.0”. That gives me some insight and the 4.5 doesn’t seem so big now.
 
Back
Top