Leak down test after spewing water at the track

Only way to find the limit is to FIND it. Morris has made 2500 hp on pump gas. I'm not enough of an asshole to think I know more about tuning the he does.
I do, and you probably do too. Nobody needs to be an asshole to see the man is an idiot.

If you are capable of reading plugs and thinking logically you know more about this than he does.

I'm not sure this isn't a parody video. I apologize if this is actually some April Fool's joke. He actually repeats the statement several times in this that timing does not need to be retarded as boost increases. His convoluted word salad would make comeallah proud, she might actually understand what he says in this video. He doesn't understand boosted combustion at all. What a clown to tell people it isn't necessary to retard with boost.

Apparently, in his pea brain he thinks every ICE research effort published in the last 100 years by NACA, MIT, SAE, et al, and all the actual engineers who produce millions of boosted OE engines are wrong and he alone is right about ignition timing.

Watch this and be honest, explain how you agree with his opinions about timing. I applaud his accomplishments and success, but he is a fool about this ignition advance deal.

 
Engine is only 13:1? Then a -7 is probably ok. I have to run -8's, 14.5:1. I run -7's on the slow engine, 10.25:1.

Is that overflow tank mounted upside down? That is the air bleed hole which is at the top of my tank. That hole is too perfect to have just happened.

I only run a 15psi cap, double-enter, fricking hot summer days, race gas, no issues cooling it. On a nasty day I leave the line at 160, return road goes up to 180, cools back down within 10 minutes or less, depends on the humidity. Many times I am making passes within 10 minutes running two classes and round-robin later in the day.

I would not be putting -6's in that engine. If you can't get it to run clean fix the carb or ditch it for EFI..........
 
Engine is only 13:1? Then a -7 is probably ok. I have to run -8's, 14.5:1. I run -7's on the slow engine, 10.25:1.

Is that overflow tank mounted upside down? That is the air bleed hole which is at the top of my tank. That hole is too perfect to have just happened.

I only run a 15psi cap, double-enter, fricking hot summer days, race gas, no issues cooling it. On a nasty day I leave the line at 160, return road goes up to 180, cools back down within 10 minutes or less, depends on the humidity. Many times I am making passes within 10 minutes running two classes and round-robin later in the day.

I would not be putting -6's in that engine. If you can't get it to run clean fix the carb or ditch it for EFI..........
You guys are funny. That hole happened that day, at that moment. Yes, a perfect fucking hole. I was just as shocked as you guys are. The tank has a fitting bung at the top and the bottom, that’s it. I have a 25”x13” radiator. I’m willing to bet your radiator is bigger than that.

I have 7’s in the car and they are staying there. I’m trying to get the car out Friday and I still have things to do. Efi doesn’t fix everything lol

The carb is brand new. I’ll get it figured out with the help of you fine folks and by me fucking with it.

Sometimes things happen for a reason. If I didn’t pull the carb to drill the hole in the spacer I might have never found those fucking balls before it was too late.
 
You guys are funny. That hole happened that day, at that moment. Yes, a perfect fucking hole. I was just as shocked as you guys are. The tank has a fitting bung at the top and the bottom, that’s it.

When it puked water at your house when you forgot to turn the fan on, where did the water come out at?
 
He doesn't need EFI. And this is coming from me with all my cars efi (just because they already came with it)

If it were a street car, yes, you can tune all the part throttle etc with efi better, or rather easier

He will just probly go slower with efi. Carb has cooling effect. Even some of the most impressive n/a ls's out there ran a carb
Not true, we did a magazine article which proved otherwise.
But I'm not trying to help him spend money or go faster, just offered him some advice on how to get idle, part throttle, and full throttle controlled pretty damn easy.
 
The top fitting had a hose pointed down.
Is there a small hole in the top of the tank?

Unless it is being run as a recovery system there should be a very small bleed hole.

If you have no hole on the top, I bet you have it upside down and that hole was there all that time designed to let you chose whether to use it as a recovery tank or an overflow tank.

Just throwing suggestions out there..............

The -7's are ok, do not put any -6's in there unless you have cylinders that are pig-rich i which case you should fix that issue, but not bandaiding them with hotter plugs.
 
Is there a small hole in the top of the tank?

Unless it is being run as a recovery system there should be a very small bleed hole.

If you have no hole on the top, I bet you have it upside down and that hole was there all that time designed to let you chose whether to use it as a recovery tank or an overflow tank.
Again, no hole! Lol
Threaded bung too and bottom. I don’t know how else to say it.
You can call Ron Davis yourself and ask him how it’s made if you’d like.
 
I want to get the car to the track tomorrow and I’m running out of time. I tried to get fancy with the overflow tank. I welded up the hole and that went fine. Then I drilled two more holes to weld bungs on the side. I was going to screw elbows in and run a clear hose along the side so that I could see how much water was in it. I started to weld the first bung and the heat and coolant residue did not like each other and it blew a hole.

My wife is going to grab a plastic bottle from O’Reilly’s this morning. I’ll figure out a way to mount it and run that. I also purchased a new one from Meziere. It was pricey, but I figured it was ok since I’m saving a lot of money by not going efi 😝. Has the breather on top that would vent it and mist it it ever overflowed.

IMG_7344f5a6b5c998a8b645.jpeg
 
I have never seen an overflow tank with a small hole at the top for a "breather" like some have said.
While tearing down this new to me dragster,I took a look at what someone had done with the catch can.
They must have had a problem with cooling and decided that the solution was to drill a 1/4 inch hole at the top of the aluminum can,insert a piece of plastic tubing,silicone it to the can to "seal" it and run the tubing along the frame rail to exit behind the rear tires and onto the track. WTF.
They were also were running a 30 lb moroso cap.
I tapped the hole they drilled and plugged it. I also installed a 14 lb cap as that is what we use on the Mustang.
While we were doing some heat cycles on the new engine,we were playing with the box for a few minutes waiting for it to warm up got distracted and the cap relieved pressure that blew the hose off the recovery tank and puked water. Quickly turned the pump on and out temp was only at about 180.
Does not seem like it was running very long to do that. So I am a little concerned if it will be an issue ,but with the pump on and fan there is no problem just idling.
I wonder if they had an issue with flow rate on the cross flow rad that is an older unit,also there is no shroud just an average fan zip tied through the rad.
12 -AN lines.
Thinking of going to a larger AFCO double pass radiator with a shroud and larger fan and a cap in the 24 lb range. Hence my earlier question about determine cap pressure size.
That is a nice looking tank you ordered,interested in your outcome this weekend.
 
I have never seen an overflow tank with a small hole at the top for a "breather" like some have said.
While tearing down this new to me dragster,I took a look at what someone had done with the catch can.
They must have had a problem with cooling and decided that the solution was to drill a 1/4 inch hole at the top of the aluminum can,insert a piece of plastic tubing,silicone it to the can to "seal" it and run the tubing along the frame rail to exit behind the rear tires and onto the track. WTF.
They were also were running a 30 lb moroso cap.
I tapped the hole they drilled and plugged it. I also installed a 14 lb cap as that is what we use on the Mustang.
While we were doing some heat cycles on the new engine,we were playing with the box for a few minutes waiting for it to warm up got distracted and the cap relieved pressure that blew the hose off the recovery tank and puked water. Quickly turned the pump on and out temp was only at about 180.
Does not seem like it was running very long to do that. So I am a little concerned if it will be an issue ,but with the pump on and fan there is no problem just idling.
I wonder if they had an issue with flow rate on the cross flow rad that is an older unit,also there is no shroud just an average fan zip tied through the rad.
12 -AN lines.
Thinking of going to a larger AFCO double pass radiator with a shroud and larger fan and a cap in the 24 lb range. Hence my earlier question about determine cap pressure size.
That is a nice looking tank you ordered,interested in your outcome this weekend.
I know that I have mentioned Stewart in the past and people have said don't listen to people trying to sell you something. Really? lol

 
By the way, a little later in the morning I'm going to fire off the car and check header primaries with a heat gun to see if number 4 is different. Now that I am sure the plug is snapped on. If something is still a-miss, I can try swapping that plug wire. I think I have some firecores from my 331 combo in a box somewhere.
 
I've had 2 bottles that both had an 1/8" breather hole. Tapped so you could install a button head Allen if not needed.

The info on coolant pressure is one of the reasons I don't prefer elec WPs. A mech pump generates much more block water press. Not really a factor on a race car, but on the street.
 
I have never seen an overflow tank with a small hole at the top for a "breather" like some have said.
While tearing down this new to me dragster,I took a look at what someone had done with the catch can.
They must have had a problem with cooling and decided that the solution was to drill a 1/4 inch hole at the top of the aluminum can,insert a piece of plastic tubing,silicone it to the can to "seal" it and run the tubing along the frame rail to exit behind the rear tires and onto the track. WTF.
They were also were running a 30 lb moroso cap.
I tapped the hole they drilled and plugged it. I also installed a 14 lb cap as that is what we use on the Mustang.
While we were doing some heat cycles on the new engine,we were playing with the box for a few minutes waiting for it to warm up got distracted and the cap relieved pressure that blew the hose off the recovery tank and puked water. Quickly turned the pump on and out temp was only at about 180.
Does not seem like it was running very long to do that. So I am a little concerned if it will be an issue ,but with the pump on and fan there is no problem just idling.
I wonder if they had an issue with flow rate on the cross flow rad that is an older unit,also there is no shroud just an average fan zip tied through the rad.
12 -AN lines.
Thinking of going to a larger AFCO double pass radiator with a shroud and larger fan and a cap in the 24 lb range. Hence my earlier question about determine cap pressure size.
That is a nice looking tank you ordered,interested in your outcome this weekend.
This one is vented:


This one is not:


I have the vented style in both of my cars. Not this brand, but very similar. They have a very small hole in the top to let them breath. Not sure if his was designed to have the hole in it or not. Doesn't matter now, he welded it shut. If it was designed to have the hole in it, it would have been installed up obviously.
 
I want to get the car to the track tomorrow and I’m running out of time. I tried to get fancy with the overflow tank. I welded up the hole and that went fine. Then I drilled two more holes to weld bungs on the side. I was going to screw elbows in and run a clear hose along the side so that I could see how much water was in it. I started to weld the first bung and the heat and coolant residue did not like each other and it blew a hole.

My wife is going to grab a plastic bottle from O’Reilly’s this morning. I’ll figure out a way to mount it and run that. I also purchased a new one from Meziere. It was pricey, but I figured it was ok since I’m saving a lot of money by not going efi 😝. Has the breather on top that would vent it and mist it it ever overflowed.

IMG_7344f5a6b5c998a8b645.jpeg
Damn nice tank but dont ever tell me how pricy my ARB kit was again. 😂 😂 😂 😂
 
Back
Top