Leak down test after spewing water at the track

I'm with the chief. My overflow bottle has a small hole in it at the TOP to allow it to breath. I run the rad line to the bottom of the bottle to use it has a recovery bottle. How is yours run?

What's the heat range on the plug? How much run time on that set? I'd say the idle,part throttle,and transition tuning is why they are fouled.
My overflow is ran exactly like you described. There was no blockage, so I'm still scratching my head on this one.

The plugs are NGK 4091's (7'). Same plugs ive been running since the motor has been running for the past 2 years. I think that you are 100% correct on the idle, part throttle tuning. I just put a dominator on it and I'm still adjusting things.

Plugs have been in for a couple months now.
 
I think through our past conversations you've said you haven't made a run, shut it down, and pulled plugs immediately. Why not
 
Looks like the coil is good. Summit shows resistance ratings for this coil to be primary .016 ohms and secondary 30.00 ohms

Primary was .1 ohm (higher than the rating, but looks acceptable from what I've read)
Secondary was 30.1 ohms
 
I'm with the chief. My overflow bottle has a small hole in it at the TOP to allow it to breath. I run the rad line to the bottom of the bottle to use it has a recovery bottle. How is yours run?

What's the heat range on the plug? How much run time on that set? I'd say the idle,part throttle,and transition tuning is why they are fouled.

I’m with both of y’all on that just being the vent. Mine is the same, pointed up & sprayed a mist when my newer CPR pump failed.
That was my initial thought but wanted to see if I was alone on it.
Something is going on there with the overheat.

Carb sounds like a typical 3 circuit???
 
I’m with both of y’all on that just being the vent. Mine is the same, pointed up & sprayed a mist when my newer CPR pump failed.
That was my initial thought but wanted to see if I was alone on it.
Something is going on there with the overheat.

Carb sounds like a typical 3 circuit???
Yes, 3 circuit.

So far I've checked the overflow and no blockage
Water pump is working, but I'm going to check voltage while running today to make sure it is getting full 12v.
Same with the fan. It's working, but I will check voltage while running later.
There is no thermostat in it, so it just free flows. Using -16an hoses top and bottom.
I ordered a new cap last night; it will be here tomorrow. Ron Davis radiator has a flat top for the cap, so some caps won't work. It had an 18lbs cap, I'm switching to a 20lbs.

Edit: I'm also thinking there might have been an air pocket in the system. I was running the car in the garage the week before and the water pump wasn't on. After I shut the car off, it did puke some water onto the floor. What was odd is that the temp gauge did not read like it was that hot. I got sidetracked and never topped it off.
 
Yes, 3 circuit.

So far I've checked the overflow and no blockage
Water pump is working, but I'm going to check voltage while running today to make sure it is getting full 12v.
Same with the fan. It's working, but I will check voltage while running later.
There is no thermostat in it, so it just free flows. Using -16an hoses top and bottom.
I ordered a new cap last night; it will be here tomorrow. Ron Davis radiator has a flat top for the cap, so some caps won't work. It had an 18lbs cap, I'm switching to a 20lbs.

Edit: I'm also thinking there might have been an air pocket in the system. I was running the car in the garage the week before and the water pump wasn't on. After I shut the car off, it did puke some water onto the floor. What was odd is that the temp gauge did not read like it was that hot. I got sidetracked and never topped it off.

There are more 3 to 2 circuit conversion kits than you can shake a stick at.

There’s a reason for that.

You’re edit makes sense as it never had a problem until it did. That water that puked should have come out of that little hole in the recovery tank.
 
There are more 3 to 2 circuit conversion kits than you can shake a stick at.

There’s a reason for that.

You’re edit makes sense as it never had a problem until it did. That water that puked should have come out of that little hole in the recovery tank.
I specifically asked BLP if the carb was going to be a 2 circuit or 3 circuit because I read 3 circuits were harder to tune. Mark Shieb said it's a 3 circuit because 2 circuits run like dog shit lol

I definitely think cruising in the pits is an issue because it's very fat at part throttle. I asked him about it yesterday and he blamed my 4500 to 4150 adapter. :confused:
 
I'm betting that puke tank had a foreign particle in it that failed. Hard to believe with a 18 lb cap. You running a thermostat or a reducing washer? How old is the cap? Are you pump gas or race gas. It's very difficult to read plugs on todays pump gas with all the shit in it. Sounds like you are very rick when not WOT. That reading may be normal. What do they look like if you pull them immediately after a pass like at scales?
 
I specifically asked BLP if the carb was going to be a 2 circuit or 3 circuit because I read 3 circuits were harder to tune. Mark Shieb said it's a 3 circuit because 2 circuits run like dog shit lol

I definitely think cruising in the pits is an issue because it's very fat at part throttle. I asked him about it yesterday and he blamed my 4500 to 4150 adapter.

🙄

I have used that adapter pointed both ways & never had a good carb run bad. YMMV

There’s probably 10 guys in here that could build you a better 2 circuit out of old spare parts. lol
 
I wonder if I’m getting a voltage drop from the coil. The length of 14ga wire is approximately 7’ maybe more. It runs from drivers side fender under hood to inside floor board on passenger side.

I’m not saying that is the cause of #4 misfiring, but maybe it’s not helping spark energy?

I’ll check voltage at the coil later. Getting ready for work.

With a CD box don't try to measure voltage at the coil. With a CD there is only a brief pulse of high voltage (550+V) at the coil when the box discharges the capacitor and the large pulse of energy can damage the volt meter. There is no voltage at the coil to measure unless the engine is running. Nothing should ever be connected to the coil except primary wires the high voltage wire to the spark plugs.

What you need to do is use the DVM to measure the ohms resistance of each plug wire. Measure from the terminals inside the distributor cap to the plug terminal in each spark plug boot.
 
I specifically asked BLP if the carb was going to be a 2 circuit or 3 circuit because I read 3 circuits were harder to tune. Mark Shieb said it's a 3 circuit because 2 circuits run like dog shit lol

I definitely think cruising in the pits is an issue because it's very fat at part throttle. I asked him about it yesterday and he blamed my 4500 to 4150 adapter. :confused:
These are odd statements from someone who allegedly understands carburetors.

If the adapter is the tall 2-1/2" tapered one, and not the 1/2" thick spacer type, I think on many engines the tall adapters may work better on a 4150 flange manifold than a dedicated 4500 manifold. The short adapters kill the air flow because they encroach on the throttle bore area too close to the bottom of the carb and act like they block 25% of the bore area. On a flow bench a 1050 Dominator flows about 750 with the restriction of the short adapter under it, but the tall 2-1/2" adapter has no effect on air flow.
 
These are odd statements from someone who allegedly understands carburetors.

If the adapter is the tall 2-1/2" tapered one, and not the 1/2" thick spacer type, I think on many engines the tall adapters may work better on a 4150 flange manifold than a dedicated 4500 manifold. The short adapters kill the air flow because they encroach on the throttle bore area too close to the bottom of the carb and act like they block 25% of the bore area. On a flow bench a 1050 Dominator flows about 750 with the restriction of the short adapter under it, but the tall 2-1/2" adapter has no effect on air flow.
I just got off the phone with them and Travis told me that the spacer is blocking off two air bleeds, which is likely causing the rich condition at part throttle. Their spacers have a hole in the center, the HVH does not. He said some people drill holes in them, but it's up to me on a $200 spacer.
 
Back
Top