Leak down test after spewing water at the track

I was just about to respond that I see it now. The hole won’t hurt. Some of them come with that hole anyway.

You should call BLP & tell them 2 things.

1. The baseplate negates having to drill any holes so stop saying that.

2. There were plastic balls stuck in your new expensive carb & you thought maybe he’d like to know that going forward so his next customer doesn’t think bad about him (Veiled reference). Maybe he’ll send you some free stuff. LMOAO.
 
You should call BLP & tell them 2 things.

1. The baseplate negates having to drill any holes so stop saying that.

2. There were plastic balls stuck in your new expensive carb & you thought maybe he’d like to know that going forward so his next customer doesn’t think bad about him (Veiled reference). Maybe he’ll send you some free stuff. LMOAO.
It is a shame that I didn’t realize the slots before I drilled the hole. It’s more of a shame that it’s their carb and didn’t know. However, I’m not worried about the hole. It is what it is.

I did tell them about the balls. Took pics and sent them to Mark. He apologized, no free shit coming my way. I did say this could have been bad, he responded that it probably would have went straight out of the exhaust. I said we can what if this all day, but it could have done damage. I would have never been able to explain it.

I would have posted my issues here and we would all be trying to figure out how I fucked up my motor.
 
I haven't read the role of the replies but that's definitely not oil that's weak ignition coupled with an overly rich condition on that plug. That overflow with that perfectly round hole in the bottom of it is my guess a factory defect as those are minimum of .080 and to blow a perfect little pinhole in it like that would be extremely odd or rare.
 
Run -5 or -6 all cylinders.
Read em properly after a good run.
Actually, after doing more research, the 6’s are not 3/4” reach. It doesn’t look like they make the racing plug in a 5-6 with 3/4” reach. Still looking.
 
What is your engine's compression ratio ?
 
Here we go lol
13:1
NGK 7 should be OK. Like you said, R5671A-7 is it in 'racing' plugs.

You shouldn't use a hot plug to put a tourniquet on a bleeding carburetor. Tune the carb so it ain't so steeeenking pig rich. We don't need no steeeeeenkeeeng rich carbs.
 
Last edited:
NGK 7 should be OK. Like you said, R5671A-7 is it in 'racing' plugs.

You shouldn't have to use a hot plug to put a tourniquet on a bleeding carburetor. Tune the carb so it ain't so steeeenking pig rich. We don't need no steeeeeenkeeeng rich carbs.
Flame propagation rate may dictate a step hotter plug, as well as fuel characteristics.
Give it what it wants.
 
Flame propagation rate may dictate a step hotter plug, as well as fuel characteristics.
Give it what it wants.

1: How do you determine flame propagation rate?

2: How does flame propagation rate affect plug heat range requirement?

3: How does compression ratio affect plug heat range?
 
Why are you not using open plenum type gasket?
Because all of the dyno results I’ve ever seen, the HVH 4 hole makes more power. In particular Eric Weingartner talks about it when doing back to back testing. However, I have an open on the way to try out as well.
 
I could also see if it wants more timing. I have not touched it since middle of last year. As a matter of fact, I didn’t even touch it during the dyno session last year. We only played with jets because at the time, the timing was set where I was hitting max mph at the track.

A bit has changed since then.
 
Timing is 30*, but I know that these AFR 220's have a fast burn chamber and don't like a lot of timing, but it will be worth a try to bump it a degree and see if it picks up.
I would retard it first. Less can't hurt anything, but more can push the pivot pooch cylinder into detonation. (or preignition if you mess with hotter plugs)

Steve Morris school of tuning, "Throw some more timing in it" and then explain why shit blew up and what went wrong.
 
I would retard it first. Less can't hurt anything, but more can push the pivot pooch cylinder into detonation. (or preignition if you mess with hotter plugs)

Steve Morris school of tuning, "Throw some more timing in it" and then explain why shit blew up and what went wrong.
After all of the other checks that I have done, I'm still thinking that the plug wire may not have been on all the way. I started timing at 24* when this thing hit the track, but your right. It won't hurt to set it at 29* and then bump from there.
 
Because all of the dyno results I’ve ever seen, the HVH 4 hole makes more power. In particular Eric Weingartner talks about it when doing back to back testing. However, I have an open on the way to try out as well.
I'm talking just the gasket, you wouldn't be blocking or inhibiting flow from those center bleeds
 
Back
Top