Leak down test after spewing water at the track

Drill baby drill.

You know your ass is going to end up with a different intake next year anyway
 
I just got off the phone with them and Travis told me that the spacer is blocking off two air bleeds, which is likely causing the rich condition at part throttle. Their spacers have a hole in the center, the HVH does not. He said some people drill holes in them, but it's up to me on a $200 spacer.
You are moving the goal posts.

First you call it a "4150 to 4500 adapter" and now you say it is a "spacer".

Is it a 4-hole 4500 spacer or open 4150 to 4500 adapter?
 
You are moving the goal posts.

First you call it a "4150 to 4500 adapter" and now you say it is a "spacer".

Is it a 4-hole 4500 spacer or open 4150 to 4500 adapter?
No, I didn't call it a 4150 to 4500 adapter. I called it a 4500 to 4150 adapter, try to keep up.

Spacer / adapter same shit different smell.

You won't believe what I found when I pulled it apart.
 
I am not posting this to bash BLP, but this could have been bad. In their defense I did ask them to expedite it since the season is almost over. I’m posting this for @89 Fox SBF . In the event he ever buys a carburetor. Hole in the adapter or not the air bleeds would not have mattered.

These 2 rock hard plastic balls were in the bottom of the air bleed holes. I had to pull the air bleeds out and punch these out. I don’t know if those are there to protect the threads or what, but I’m glad they didn’t get sucked in!

IMG_7329.jpeg

IMG_7331.jpeg


After I popped those out, I marked and drilled a hole in my 4500 to 4150 adapter spacer 😝

IMG_733283a594e8d6457a18.jpeg
 
Welp. I'm out lol
Fucking shit never ends. I put it all back on, flip fuel pump on to fill the bowls and the carb overflows. Drained them and it did it again. I don't know if the needle and seats got stuck from flipping the carb upside down or what. Pulled the bowls off and then got busy with work, so had to run back inside. Fuck me.
 
Fucking shit never ends. I put it all back on, flip fuel pump on to fill the bowls and the carb overflows. Drained them and it did it again. I don't know if the needle and seats got stuck from flipping the carb upside down or what. Pulled the bowls off and then got busy with work, so had to run back inside. Fuck me.
And this is what we do for fun Lol
Good to hear you’re making progress
 
the balls are abrasive media used in the vibrating or tumbling deburring and polishing process

need to measure the resistance of all the wires
 
Run -5 or -6 all cylinders.
Read em properly after a good run.
Ordered (12) #6’s. Picking them up tomorrow after work.
Looks like the TB has slots cut into it to allow for the signal regardless of a spacer. ?
4 hole spacer. No where for it to go. I drilled the hole. It idles smoother now.

IMG_7177056f88347bdbcd34.jpeg


the balls are abrasive media used in the vibrating or tumbling deburring and polishing process

need to measure the resistance of all the wires
Just checked all of the wires. From the bottom of the cap to the end of the wire. I also checked #4 with the spark tester and it made a light show in the garage. I didn’t pay close enough attention when I initially pulled the wire off. I’m wondering if I didn’t have it seated all the way.

Resistance check
#1) 95.6
#2) 106.7
#3) 105.1
#4) 104.7
#5) 90.2
#6) 86.6
#7) 111.7
#8) 118.5

Water pump and fan getting 13.5V when running.
 
I wonder if I’m getting a voltage drop from the coil. The length of 14ga wire is approximately 7’ maybe more. It runs from drivers side fender under hood to inside floor board on passenger side.

I’m not saying that is the cause of #4 misfiring, but maybe it’s not helping spark energy?

I’ll check voltage at the coil later. Getting ready for work.
It is important that the length high-voltage coil wire is short as possible, so mounting the coil close to the distributor is ideal.

The length of the 14ga wires from CD box to coil is not as critical as the high voltage wire(s), but short as reasonable is desired.

The wires (purple and green) from the distributor or crank trigger must be as far as possible from high or low voltage coil wires, because EMF pulses in the coil and wires will induce false trigger pulses, Securing trigger and coil wires to the same roll bar tube will cause the box to go wild and fire crazy out of time or continuously.
 
Ordered (12) #6’s. Picking them up tomorrow after work.

4 hole spacer. No where for it to go. I drilled the hole. It idles smoother now.

IMG_7177056f88347bdbcd34.jpeg



Just checked all of the wires. From the bottom of the cap to the end of the wire. I also checked #4 with the spark tester and it made a light show in the garage. I didn’t pay close enough attention when I initially pulled the wire off. I’m wondering if I didn’t have it seated all the way.

Resistance check
#1) 95.6
#2) 106.7
#3) 105.1
#4) 104.7
#5) 90.2
#6) 86.6
#7) 111.7
#8) 118.5

Water pump and fan getting 13.5V when running.
Good job on the wire resistance check. Is the difference in resistance roughly the difference in length?

The picture in #45 shows slots in the bottom of the carb which make a path for the air to get from the center bleeds to each throttle bore. The difference in how it runs is the result of opening up the air leaks from the bleeds in the center. of the body.
 
Back
Top