I found a bunch of gold! I'm rich!

Well, now what

  • Change the oil, run it a few more miles, check again

    Votes: 32 78.0%
  • Pull it apart.

    Votes: 9 22.0%

  • Total voters
    41
I'm looking for pics or mention of the rockers you are using. Would they be gold anodized? Maybe you have one chewing itself up.

Edit - I see in your build thread you are using aluminum rockers, but blue. But you also mention overtightening, and rocker rattle on start up. Again, any possibility that what you are seeing in the oil is aluminum from a damaged rocker?
 
Seems to me (and I freely admit to being extremely ignorant on the majority of what's being discussed in here) that changing the oil, doing the diesel fuel, and then fresh oil and check for stuff is way better than just putting it on a trailer and parking it.
You can always do that, at any time.
I'll also share that the guy who built the engine in my race bike is way smarter than me, extremely knowledgeable, and has probably 30 years building motorcycle engines, mostly for racing (dirt and roadracing).
He told me that he told all his clients, when they got a new bike/new engine that they needed to put about 100 miles on it, drain the oil and put in cheap, new oil. Lather, rinse, repeat for 400-500 miles.... until there wasn't any more particulates in the oil. Maybe things are different with bikes, or maybe I'm not remembering what he said correctly (pretty sure I am though)... but it seems like things may not be as bad as you think.
Anyways, that's the 2 cents of someone who can't afford to buy performance race engines, and the approach I would take if I were in your shoes.

I just feel bad at the level of disappointment you're feeling. That absolutely sucks. :(
absolutely right… he has nothing to lose by going this route.. ALL motors will show break in particulates.. it’s a fact. All the moving parts have to get to know each other, and cast off flakes etc in the process.. could be as simple as the thrust bearing wearing in because it’s a clutch car…

As long as the oil pressure is normal and there are no knocks, I’d do the oil change and run it for a while… and look at the filter again.. the motor will tell you if it’s not happy internally…
 
So I thought the rockers weren't adjusted correctly, because I can twist the rocker by hand when the valves are closed (yes, the rocker arm, not the pushrod)

Well I just finished setting valve lash again (half turn past zero lash) and locking them down.

After rotating engine by hand, the rocker arms still do this. I suppose it's normal and I'm an idiot?
 
Also, the bits of aluminum I found in the filter are likely from around the head bolts. Why wouldn't this be cleaned up? What the cock sucking fuck is this shit


 
Front drain plug magnet is just metal sludge. I was running comp cams break in oil, not sure if the additive would have something to do with that.


 
Your rockers are going to move like that.
Can’t explain the shavings around the head bolts. (Why didn’t you stud it?)
The front plug is just picking up crap that was probably in the lifter valley before assembly. Probably not cleaned very well on assembly.

Plug in, oil in, filter on, turn key and take a trip. Don’t get all hussy. Clear your head and take a trip.
 
Where is that coming from?

Either the oil galley, cam plugs or rear main seal. I can't see it, but the leak presents itself between the scatter shield and bellhousing. The flywheel to crank bolts are blind holes, not through holes. Nothing else it could be.
 
Last edited:
Front drain plug magnet is just metal sludge. I was running comp cams break in oil, not sure if the additive would have something to do with that.



Mine looks like that all the time. I'm told it is the extra zinc (also used in break in oils) that I add to my oil. Take care. Tom Worthington
 
If your using synthetic break in oil or additives to oil, it may be those compounds findings away past the main seal.
Do you have adequate crank case ventilation, crank case vacuum?
Put plain old every day oil in it and be happy.
There is not enough shit to worry about on that plug and rag
Your likely going to see at least that much on every oil change.
 
Front drain plug magnet is just metal sludge. I was running comp cams break in oil, not sure if the additive would have something to do with that.


Fox I get that "paste/sludge" stuff on my magnetic drain plug at every oil change . Its ring wear so I have been told , and on a new build that is expected . I believe that it is normal because if it was anything other than normal I would have had serious issues long before now. I cant tell if its "paste/sludge" or more liquid like break in lube , but either way that is normal .
I mentioned many posts ago that the metal COULD be from not being cleaned (block and or heads) good after the machining process and that might be the case where it collected around your head bolts or your aluminum rockers might be "self clearancing" themselves on something like a bolt or on a valve spring retainer. . Take a good look at them , remove them so you can look at the underside of them.. As far as your oil leak, I ain't got nothing to help you out with that . But I do know, an oil leak is no reason to call it quits on a project .
 
Fox I get that "paste/sludge" stuff on my magnetic drain plug at every oil change . Its ring wear so I have been told , and on a new build that is expected . I believe that it is normal because if it was anything other than normal I would have had serious issues long before now. I cant tell if its "paste/sludge" or more liquid like break in lube , but either way that is normal .
I mentioned many posts ago that the metal COULD be from not being cleaned (block and or heads) good after the machining process and that might be the case where it collected around your head bolts or your aluminum rockers might be "self clearancing" themselves on something like a bolt or on a valve spring retainer. . Take a good look at them , remove them so you can look at the underside of them.. As far as your oil leak, I ain't got nothing to help you out with that . But I do know, an oil leak is no reason to call it quits on a project .

This. But I do understand wanting to take a sledgehammer to a project that's pissing me off.
 
You wana cry, go read my thread in the cars for sale thread. It got much worse, nobody could get my fox body in time so it just stayed there, and after the house sold my wife left me so it's been a great year or two.
should have left the wife there with the new owner and taken the car with you.
Hind sight is always 20/20.
 
If your using synthetic break in oil or additives to oil, it may be those compounds findings away past the main seal.
Do you have adequate crank case ventilation, crank case vacuum?
Put plain old every day oil in it and be happy.
There is not enough shit to worry about on that plug and rag
Your likely going to see at least that much on every oil change.

It's comp cams 10w30 break in oil. I don't see how that would cause a leak but I'll entertain the thought

I have vent on each valve cover.

I don't know about crank case vacuum. If it's not something different than what I read on the vacuum gauge, I have about 18 in/hg at idle
 
It's comp cams 10w30 break in oil. I don't see how that would cause a leak but I'll entertain the thought

I have vent on each valve cover.

I don't know about crank case vacuum. If it's not something different than what I read on the vacuum gauge, I have about 18 in/hg at idle

I think he's asking if you have a good, functioning PCV system.
 
It's comp cams 10w30 break in oil. I don't see how that would cause a leak but I'll entertain the thought

I have vent on each valve cover.

I don't know about crank case vacuum. If it's not something different than what I read on the vacuum gauge, I have about 18 in/hg at idle
Like no pcv valve at all ?
That’s not good….

I’ve seen many seal leaks quit just by getting the crankcase ventilated properly…
 
Back
Top