I found a bunch of gold! I'm rich!

Well, now what

  • Change the oil, run it a few more miles, check again

    Votes: 32 78.0%
  • Pull it apart.

    Votes: 9 22.0%

  • Total voters
    41
We don't run composite gear on engines with internal oil pumps. The SBF love to destroy thrust bearings, we run two dumps on the trans to keep line pressure low while building boost. On last tear down we noticed some gold color in the clear view filter, we had no thrust movement and no bearing wear. still don't know where it came from.

What is different in the oiling on ford that they don't like high oil pressure? I was told keep it under 65
 
Not true you mean fuck! The oil won't get here until Thursday because God forbid I buy ots oil from vato zone.

Setting lash and putting new filter on tonight. I'll fill and run anther 10 miles and investigate again once the oil arrives.

Comp break in oil from summit on the way, same as I used first time
It doesn't matter if you use less expensive oil for this experiment. Run some good oil, but nothing exotic. It's going to be in the engine for less than 50 miles.
 
God damn Go down to the local fucking truck stop You know the same one where you turn tricks in the bathroom and get a fucking gallon of Delo 400 and pour in that motherfucker and start it up!

Jesus fucking Christ If you make getting pussy this hard it's no wonder you're gay!
 
For oil you're dumping just buy anything don't waste money on something you're gonna throw out
I use high detergent straight 30 when I start a fresh engine. I run it three times, from cold to operating temp, let it cool off completely, do it again later. On the third run, once it is warm, I sit in and and load it against the convertor. You can't do that with a stick. After that I dump the oil, cut open the filter, if it all looks good Mobil 1 10W/30 and a WIX filter and off to the track to beat it like I stole it! :)

If it's a street car then I do all the same stuff, except it will get driven to the track instead of towed. ;)
 
Did you cut the filter open? Open the pleats and look in there for metal? I have a couple of oil filter openers that are pretty easy to use and work like a tubing cutter so there is no extra metal added from the cutting process. I cut the filters open on both race cars each time I change the oil. I want to catch something early before it becomes a huge mess.

You have a lot of glitter in that oil, a lot. I have never had that on my stuff. Put some high detergent oil in there and run it for a few minutes to get it up to temp then take the filter off and cut it open.
 
Not true you mean fuck! The oil won't get here until Thursday because God forbid I buy ots oil from vato zone.

Setting lash and putting new filter on tonight. I'll fill and run anther 10 miles and investigate again once the oil arrives.

Comp break in oil from summit on the way, same as I used first time
If you already ran the break in oil, you need not run it again. Go get some conventional oil from Wally world and a good filter, put some miles on.
It will rear its ugly head if there is more of an issue.

 
Jesus Christ, don't overthink this. Everything has been lapped with that glitter bomb sluice that's been run through the engine. Fill it up with some cheap Castrol 10/30, spin a new filter on, put a couple of miles on it to get some heat in the oil then lay into it. :D If it still has oil pressure, put a few miles on it then drain the oil and cut the filter open.
 
If you already ran the break in oil, you need not run it again. Go get some conventional oil from Wally world and a good filter, put some miles on.
It will rear its ugly head if there is more of an issue.

Agreed... "high mileage" oil
 
Probably has a Screedmaster timing set with a brass thrust washer.

You can cut the filter open with a hammer and chisel. A pal and I did this on a big piece of butcher paper to catch the oil and make the flack easy to see on the white paper. One person holds the filter on the floor or bench top and rotates it as the other person cuts with the hammer and chisel right at the edge of where the can is crimped to the flange. The chisel shears the sheet metal can from the edge of the flange.
 
Jesus Christ, don't overthink this. Everything has been lapped with that glitter bomb sluice that's been run through the engine. Fill it up with some cheap Castrol 10/30, spin a new filter on, put a couple of miles on it to get some heat in the oil then lay into it. :D If it still has oil pressure, put a few miles on it then drain the oil and cut the filter open.
Let's not go into "common" sense mode Dana! 🤣
 
Probably has a Screedmaster timing set with a brass thrust washer.

You can cut the filter open with a hammer and chisel. A pal and I did this on a big piece of butcher paper to catch the oil and make the flack easy to see on the white paper. One person holds the filter on the floor or bench top and rotates it as the other person cuts with the hammer and chisel right at the edge of where the can is crimped to the flange. The chisel shears the sheet metal can from the edge of the flange.
One of the side cutting can openers works also. Just throw it in the dishwasher afterwards. 😁
 
Back
Top