Breaking up at high rpm, carb issues, and converter issues.

If the throttle shaft is large enough and strong enough it doesn't flex, and the blade is not offset so much it gives it too strong a closing force, I guarantee it can be made to seal to minimum near zero air flow and be made to open gradually. Is the throttle shaft on ball bearings, like a Weber carb? If it isn't, it should be.

Have you studied the throttle linkage bell crank on the throttle body on a 2004-2006 GT-40? that has a throttle cable bell crank.

Nearly every Cobra kit car has throttle linkage from hell that makes them near impossible to drive in the rain because the carb comes off idle way to quick. The well worn video of the gal pulling out of a car show into the street in her boyfriend's Cobra and the car going crazy fishtailing and running into a pole and (was it ?) a Honda car a block down the street is an example.

I've made a asphalt circle track car more than a half-second faster on a 1/2 mile touching nothing but the throttle linkage, just fixing the bell crank arrangement so the driver had throttle control that wasn't just like an on/off switch.
lol
you can watch it flex the butterfly, the shaft everything
every 500" car has made all kinds of linkage to give it some mechanical advantage
its why they idle, or they snap it open on the burnout or to go on the 2 step.
the shaft is 7" long, and centered in the bore
it sucks
but no one really cares because they have figured out how to work with it.
its a pisspoor setup, but its what they are stuck with
 
If the throttle shaft is large enough and strong enough it doesn't flex, and the blade is not offset so much it gives it too strong a closing force, I guarantee it can be made to seal to minimum near zero air flow and be made to open gradually. Is the throttle shaft on ball bearings, like a Weber carb? If it isn't, it should be.

Have you studied the throttle linkage bell crank on the throttle body on a 2004-2006 GT-40? that has a throttle cable bell crank.

Nearly every Cobra kit car has throttle linkage from hell that makes them near impossible to drive in the rain because the carb comes off idle way to quick. The well worn video of the gal pulling out of a car show into the street in her boyfriend's Cobra and the car going crazy fishtailing and running into a pole and (was it ?) a Honda car a block down the street is an example.

I've made a asphalt circle track car more than a half-second faster on a 1/2 mile touching nothing but the throttle linkage, just fixing the bell crank arrangement so the driver had throttle control that wasn't just like an on/off switch.
When I finally went to a 4bbl throttle body after running a two blade forward facing throttle body I got a rude awakening!
The throttle body was not staged, all four blades moved at the same time. Trying to drive it through the pits and do a burnout with any kind of control was a pain in the ass. But not like that single blade TB Pro Stock has to run. I was able to get linkage to stage the secondaries, then it was a pleasure.
 
Oh, and I put new plugs in it last night and gapped them @ .040". With the old box I was gapping them at .032" because I figured it was old and didn't have as much spark energy.

Even when new the Mallory had a voltage output to the coil of 525v and spark output (millijoules) of 135mj. The MSD has 570v and 160mj, so I figured that I could open the gap a little.
I am either lucky or sometimes the little shit really doesn't matter.
I take the plugs out of the box, slap some anti seize on them, and pop them in the engine.
I have never gapped a plug, never indexed a plug.
If there was a gap, I ran them!
Again, it's a 23* SBC, pretty forgiving. I was hitting that engine with up to 400hp worth of nitrous, still, never touched the gap.

And to top it off, not sure if Bob ever saw the Waste Fire setup from Holley, I still use it today.
That coil makes a spark as bright and strong as your LAWNMOWER!
No kidding!
It has to be the dwell time has to be what makes it work. It is hard to see the spark during the daytime.
Same coil pack that GM used on many of their cars and trucks, including an S10 with a 4 banger I used to run around.

Strange thing about that system was that going down the track with the nitrous flowing, you would see black smoke out the exhaust. People would say hey dude, that thing is either pig-rich or a diesel. Pull a plug and they are perfect, they would scratch their heads! I was working with Holley and Monte Smith on this issue. Chad Hendersons car did the same thing, yet the plugs came out looking like they just came out of the box, and the exhaust was perfectly clean. We never figured out what caused that to happen, had to be something with the waste fire aspect of it firing one cylinder on compression and the other on exhuast.
 
I am either lucky or sometimes the little shit really doesn't matter.
I take the plugs out of the box, slap some anti seize on them, and pop them in the engine.

I have never gapped a plug, never indexed a plug.
If there was a gap, I ran them!
Again, it's a 23* SBC, pretty forgiving. I was hitting that engine with up to 400hp worth of nitrous, still, never touched the gap.

And to top it off, not sure if Bob ever saw the Waste Fire setup from Holley, I still use it today.
That coil makes a spark as bright and strong as your LAWNMOWER!
No kidding!
It has to be the dwell time has to be what makes it work. It is hard to see the spark during the daytime.
Same coil pack that GM used on many of their cars and trucks, including an S10 with a 4 banger I used to run around.

Strange thing about that system was that going down the track with the nitrous flowing, you would see black smoke out the exhaust. People would say hey dude, that thing is either pig-rich or a diesel. Pull a plug and they are perfect, they would scratch their heads! I was working with Holley and Monte Smith on this issue. Chad Hendersons car did the same thing, yet the plugs came out looking like they just came out of the box, and the exhaust was perfectly clean. We never figured out what caused that to happen, had to be something with the waste fire aspect of it firing one cylinder on compression and the other on exhuast.
There is no magic to be had there for sure
the really heavy nitrous and blown meth we run .015
everything else we run .025 ish, or as you said, what it has out of the box.
NGK R5671a- whatever is typically .025-.030
thats where they go in
i had people (well know in the industry) tell me you HAVE to run .xxx
ond guy flew out here in the early days of efi was going to show me how it was done...lol
"we have to run .015"
i tell him there is nothing to be had, but ill do it
nothing.
ok, we have to run .035
nothing but a slight miss up high
back to .025 it is then...lol
Anyone who tells you there is magic to be had there is crazy
Ive had customer put 200 passes on the same plugs. Came in with at least .050+ gap
 
I lost track of what head is on this Ford. Some heads for Fords have really good fast burn chambers, so even though 24 is not likely enough it isn't as far retarded as you might think, compared to the 23 deg. SBC everybody seems to think sets the standard at 36. Some Fords and low valve angle SBC heads 18 & 15 deg. only need 26 to make the best HP.
I am using AFR 220 (1451's). I have been coming across a lot of posts that say AFR uses a quick burn style combustion chamber and don't like a lot of timing. So, while 24* was low, maybe not as low as I initially thought. Hopefully, I will find out tomorrow what it likes.
 
I am using AFR 220 (1451's). I have been coming across a lot of posts that say AFR uses a quick burn style combustion chamber and don't like a lot of timing. So, while 24* was low, maybe not as low as I initially thought. Hopefully, I will find out tomorrow what it likes.
24* is low, but on a head that does well with 28 to 32, it isn't that low.
Now, if it's a head like my 23* SBC with a large dome, 24 is what I would run with my 750hp engine PLUS 300hp of nitrous on top of it!
I never bothered to make enough passes to see where the thing would fall off with timing.
I found on the chassis dyno one day, I started at 36*, then went to 38* (which is what my engine builder said to run), then 40*, then 42*, finally said that's enough. Each pull it made more power, not a lot, don't really remember, maybe 10ish to the tires. But I also know that we would always wind up running 2* to 4* LESS at the actual track than the chassis dyno showed was good. I never bothered to run more than 40* on mine.

Now power adder stuff, when you play with timing on those applications, it makes a HUGE difference! A mild combo can show 25hp at the tires from 2*.............. Gotta be careful and sneak-up on that stuff. Same goes for boost, 2 psi makes a world of difference!
 
Car is loaded up, had a lot of crap to do this morning. I’m gonna take a quick PT shower and get ready to go.

Gates open @ 3pm (central time) and track goes hot @ 5pm. I’m starting to think I got a little too excited and maybe I’m going to get a reality check.
 
He probably should adjust the idle mixture screws.
i think he was referencing jetting
well i took it as he was.
but im part pollack so you cant always trust what im thinking
 
i think he was referencing jetting
well i took it as he was.
but im part pollack so you cant always trust what im thinking
I thought so too, but that is why just putting through the pits suggesting idle mixture. 12-13/1 is OK for idle, but his O2 sensor is so close to the open end of the pipe idle numbers are not accurate so the idle should be adjusted by judging how it runs and ignoring the gauge
 
After it warmed up, I went half turn out on all four corners and it went to 14’s-15’s.
if you are close to the end of the collector, reversion pulses at low rpm lie to the o2.
ignore it as itey said until at least 3500 rpm, and adjust based on how it runs, not what the sensor says
put on the new balances and adjust it by ear.
 
Back
Top