Tq converter mating issues…help!

Patriot Racer

Freeeeeeedom!
Joined
Sep 18, 2021
Messages
9,229
Reaction score
24,327
Points
153
Location
Northern Illinois
I installed my tq converter onto the transmission and heard two clunks. Installed the engine and can’t get the bellhousing and engine to mate up without binding the tq converter.

I pulled the engine back out thinking the tq converter wasn’t in all the way. I heard the clunks, but I’m still not sure if it’s all the way on. Still seems it should be on further.

Since I can’t seem to get the converter to go on any further I measured the converter pilot and the crank pilot hole. This doesn’t seem right.

 
I heard the clicks and it dropped, but it doesn’t look like it’s in all the way to me. Maybe the car is pissed I’m putting GM parts on it? 🤷🏻‍♂️

 
the depth of the crank pilot hole is .619”. The pilot on the converter is .655”.

I bought an adapter that is only .402”. Coan told me I didn’t need it because they put one on. I think they put one on that it too long. Also both the one they installed and the one I bought are slightly larger than the crank pilot hole. Pretty sure this isn’t press fit, so wtf? How much Clearance is need between the two?



The one from my C4 measures 1.33”, which makes more sense.

 
Yeah the hub on the converter should fit fairly snug but not tight.
 
I would pull the hub bushing off the converter and just see how it fits without that and then go from there
The bushing makes the hub smaller to adapt from chevy to the ford crankshaft pilot hole, which is 1.375”. I think a Chevy is like 1.7xx”.
 
Last edited:
Have you tried just the converter by itself to the engine and flexplate? Dial calipers aren’t always dead on for inside / outside measuring.
 
After scrolling through the pics a few times, it appears that you may have two issues. You have one for sure.

The new crank button is measuring 15/10,000 larger than the pilot hole in the crank flange. That needs fixed. You old one at 1.33" might be a hair loose, but would be OK.

Also, I am NOT familiar with Ford transmissions, but the new button I think measures .665" that can go into the crank flange pilot hole. The old one was .402". On a chevy or mopar transmission, you have to leave between .125- .1875" space between the front pump on the transmission and the convertor to allow for movement. At the same time, that crank flange button has to have space so it does not bottom out inside the pilot hole. Any machine shop should be able to get a grip on that button you have and get you the correct dimensions after a little math.
 
Have you tried just the converter by itself to the engine and flexplate? Dial calipers aren’t always dead on for inside / outside measuring.
I’m going to try that, but the engine is back on the stand right now. I’m gonna get my second wind here in a minute. Been at this all day and feel like I got nothing done.

Might need to hit the inside of the crank with some emery cloth. It’s starting to get rough from trying to mate the engine.
 
Converter pilot should not be a press fit.
We use the converter adapters from JW.
But I don't know what the converter overall height was built at.
I've had to trim many a converter mounting pad from competitor's converters to get a customer going.
But you definitely have an issue with that adapter.
 
Alright persistence pays off. Went back out and cleaned up the pilot on the converter with some 220. Also cleaned the crankshaft register with 220. Wiped everything down and put a light coat of assembly lube on both pieces.

Test fit the converter into the flexplate and it went in and out smoothly “slip fit”.

Reinstalled the converter to the transmission, dropped in the engine making sure everything was lined up and moving freely the whole way.

Converter slides in and out like butter and spins freely. The only problem now is that I have 7/32nds (.218”) end play. Supposed to have a minimum of 1/8” and a max of 3/16 (.1875). So I have .0305” of an inch too much end play.



Do I just throw a washer in between the flexplate and converter and bolt it up?
 
Alright persistence pays off. Went back out and cleaned up the pilot on the converter with some 220. Also cleaned the crankshaft register with 220. Wiped everything down and put a light coat of assembly lube on both pieces.

Test fit the converter into the flexplate and it went in and out smoothly “slip fit”.

Reinstalled the converter to the transmission, dropped in the engine making sure everything was lined up and moving freely the whole way.

Converter slides in and out like butter and spins freely. The only problem now is that I have 7/32nds (.218”) end play. Supposed to have a minimum of 1/8” and a max of 3/16 (.1875). So I have .0305” of an inch too much end play.



Do I just throw a washer in between the flexplate and converter and bolt it up?

Yep! If I do not have machine washers, I use good quality flat washers. As a personal preference I try to land somewhere near the middle of spec., but anything in between those numbers will git 'er done!
 
Stack a nickel and a dime, perfect converter clearance. Add shims to get the nickel and dime to fit snugly. I always weigh the shims to make sure they are the same, but it's probably not necessary.
 
Back
Top