wickSS
O.G. wick
- Joined
- Jan 25, 2021
- Messages
- 5,134
- Reaction score
- 9,291
- Points
- 153
Hell, I’ll even come down and help you.Drop it off here on the way to WV I’ll pull the motor out and take it to a reputable builder for you .
Hell, I’ll even come down and help you.Drop it off here on the way to WV I’ll pull the motor out and take it to a reputable builder for you .
It may not be as bad as you are making out to be in your mind. Step back take a deep breath.most of your expense is already done. May not need as much as you think. Yes it’s frustrating pulling it back out but that’s how this game goes.I appreciate it Mark but I'm not spending another dime on this engine. I'll set it aside for a future project and rebuild it myself eventually
It may not be as bad as you are making out to be in your mind. Step back take a deep breath.most of your expense is already done. May not need as much as you think. Yes it’s frustrating pulling it back out but that’s how this game goes.
Sometimes!Does that advice work with women too?
FactSometimes!
It's cheaper to keepher!
If you are only looking for around 400HP why not get a Blueprint engine? I have done several SBC engines of theirs for customers and also own for myself one of their complete 632 carb to pan BBC engines (which I have not used yet). They have a pretty good reputation and stand behind their product with a 30 month/50,000 mile warranty that only starts when you mail in the warranty card so you can buy and wait until you install the motor and take your time and still have the full warranty. That is what I am doing with my 632, bought it before I needed to use it as the prices keep going up and delivery times are getting longer with supply chain issues.Since this isn't anyone else's dime, they say fuck it, run it, see what happens.
The fact is the engine is toast and needs to come apart. Will it make noise and go down the road a few more times? Sure. Will the bearings turn to dust? Guaranteed.
If anyone here truly believes that amount of bearing material and ferrous shit is going to work itself out you're crazier than online dating chicks.
After i idle this engine 10 minutes to prove how fuckin stupid i am, this engine is coming out, being stuffed in the corner, and this project is essentially dead.
In case you guys didn't follow along in the build thread.. 3 different builders fucked me, over $20k into this 400hp (not joking) engine. I'm not putting another dime into it.
If you are only looking for around 400HP why not get a Blueprint engine? I have done several SBC engines of theirs for customers and also own for myself one of their complete 632 carb to pan BBC engines (which I have not used yet). They have a pretty good reputation and stand behind their product with a 30 month/50,000 mile warranty that only starts when you mail in the warranty card so you can buy and wait until you install the motor and take your time and still have the full warranty. That is what I am doing with my 632, bought it before I needed to use it as the prices keep going up and delivery times are getting longer with supply chain issues.
For $7149.00 they have a 408 long block Ford that makes 450HP and has a front sump and can also be ordered with a rear sump also, forged piston, their alloy head, hydraulic roller cam, pump gas friendly and you can just bolt on your intake, water pump and ignition and some other small bits and you are ready to go.
![]()
Ford Small Block Compatible 408 c.i. Engine - 450 Horsepower - Long Block
BluePrint Engines 408 c.i. small block Ford style stroker crate engine - longblock. Includes 30 month / 50,000 warranty & BPE Dyno Promise.blueprintengines.com
Also the factories make some pretty good crate engines, I have never gotten a Ford (although I tried to get a 460 years ago and could not for my Camper Special) but have done a lot of SBC and BBC Chevy engines and got them from Scoggins-Dickey.
Sorry that you have already spent the money on other shops that did not do a good job but this is a way to get out of the hole you are in. Perhaps the last shop will partially reimburse or give you all the money back for the failure but small shops normally are not known for doing so but you need to try.
Dave
I will just leave this here and watch it until the end for the big (little) suprise!I think he would fuck that up also unless he does exactly what i tell him. The trick with LS's is that if you can't build engines yourself or don't know someone good to do it, leave the bottom end the fuck alone as it came from GM, don't touch it.. and run diesel 15/40 because most car oils will sludge the insides of it after time and eventually stick the rings and insides of the hydraulic lifters and then people will blame the engine when it is the inferior oil's fault and not the engine itself.. and 98% of the time you will have a great experience with it to the point of after 1000x wide open throttles and burnouts you end up asking yourself 'how can this thing not have put a rod out the block by now'.....
I just happen to have kept this pic from back in the day and it is funny to me that in 2024 many car people still don't get the LS's potential. STOCK BOTTOM END n/a LS2 .... and several sbe 5.7 LS1's have done the same.. run high 9's n/a. And they were beat on badly. No need to mention what they can do with boost
![]()
I have a 2000 SLP Camaro SS (Catfish) with the LS1 and 6 speed, love the look and functionality of those cars and you can do so much on the cheap to pick them up!I think he would fuck that up also unless he does exactly what i tell him. The trick with LS's is that if you can't build engines yourself or don't know someone good to do it, leave the bottom end the fuck alone as it came from GM, don't touch it.. and run diesel 15/40 because most car oils will sludge the insides of it after time and eventually stick the rings and insides of the hydraulic lifters and then people will blame the engine when it is the inferior oil's fault and not the engine itself.. and 98% of the time you will have a great experience with it to the point of after 1000x wide open throttles and burnouts you end up asking yourself 'how can this thing not have put a rod out the block by now'.....
I just happen to have kept this pic from back in the day and it is funny to me that in 2024 many car people still don't get the LS's potential. STOCK BOTTOM END n/a LS2 .... and several sbe 5.7 LS1's have done the same.. run high 9's n/a. And they were beat on badly. No need to mention what they can do with boost
![]()
I think they are out of business now but their Meat Relish was to die for! I used to have it shipped to me from Buena Park!Well, to lighten the mood.................
![]()
I hear ya. I recently got a 2018 durango off my younger brother, fully loaded. Fucker flies, is quiet, has a fancy radio I can hook to my phone.Thanks for the reply Dave. I'm not "looking for 400hp", but remember, in 2006 a 400hp street car was really impressive. I figured I'd I could squeeze a 1/4 mile in the 11's after driving it to the track I'd be thrilled. Almost 20 years later a ford explorer with a tune and bolt ons dips into the 11s.
If I'm buying another engine, it won't be anywhere near as tame as 400hp. But with the trans, clutch, drivetrain setup I have, it'll have to be a sbf in the 700hp range.
Or like I said.. sell the thing and move on.
A 11 sec foxbody mustang is a pretty easy task. Have some friends who street raced a low 11 high 10 5.0GT back in the day and it was a stock shortblock, stock cam, stock injectors, speed density car. Had gt40 heads, roller rockers, cobra intake manifold, 150 shot of giggle juice. They drove that car all over the placeThanks for the reply Dave. I'm not "looking for 400hp", but remember, in 2006 a 400hp street car was really impressive. I figured I'd I could squeeze a 1/4 mile in the 11's after driving it to the track I'd be thrilled. Almost 20 years later a ford explorer with a tune and bolt ons dips into the 11s.
If I'm buying another engine, it won't be anywhere near as tame as 400hp. But with the trans, clutch, drivetrain setup I have, it'll have to be a sbf in the 700hp range.
Or like I said.. sell the thing and move on.
Lot of wisdom here…But, it doesn’t put the smile on my face as I get sideways with rolling burnouts with the blower screaming like a 747 is landing in the cab. Keep the car, cruise your daily. You’re still young and toys ain’t getting cheaper or easier to find.
I disassembled this engine in 2021. When I took the parts to the builder he charged me 2k to assemble the pile of parts.
Even if it's minor, putting $2k into it just to rebuild is not something I'm willing to do. I can likely spend 8k on a crate engine with more hp and a warranty.
I'll try calling the builder, but he's likely to tell me to get fucked
I think they are out of business now but their Meat Relish was to die for! I used to have it shipped to me from Buena Park!
Somebody go start a Thread about the cars we used to have, and wished we had never got rid of !