Breaking up at high rpm, carb issues, and converter issues.

Season is over. Cam gear is chewed up on the leading edge.



Not sure, but I don't think that edge of the cam gear makes contact with the distributor gear if the cam end play/thrust plate/cam sprocket/etc. is all OK.

If there isn't any (or very little) steel flack in the oil filter I would get a composite gear and throw another virgin in the volcano.

IF there is any metal in the filter I would take it apart, polish the cylinder walls and crank journals with 400 wet-or-dry, pick the flack out of the piston skirts and wash it good. Make sure there is no flack in the valve springs.
 
Not sure, but I don't think that edge of the cam gear makes contact with the distributor gear if the cam end play/thrust plate/cam sprocket/etc. is all OK.

If there isn't any (or very little) steel flack in the oil filter I would get a composite gear and throw another virgin in the volcano.

IF there is any metal in the filter I would take it apart, polish the cylinder walls and crank journals with 400 wet-or-dry, pick the flack out of the piston skirts and wash it good. Make sure there is no flack in the valve springs.
I just talked to my engine builder and he pretty much said the same thing if I’m reading what you said correctly. He said if you found no metal, that cam gear doesn’t scare him at all. He said throw a bronze gear on it, throw the crank trigger on and go racing.
 
After that experience I described above in # 584^^, I wouldn't use a bronze gear if he gave it to me. Not all bronze is created equal. Not all bronze gears are made of the right stuff.

Perhaps what would be right for you is the stock Ford actual steel gear for factory roller cam engines.
 
I just talked to my engine builder and he pretty much said the same thing if I’m reading what you said correctly. He said if you found no metal, that cam gear doesn’t scare him at all. He said throw a bronze gear on it, throw the crank trigger on and go racing.

I have used at least 40 composite gears & have never had a failure. Some were used after bronze gear issues & the composite never looks anything but new on inspection.

I have one in my own personal engine.

They are pricey but worth it in my opinion.
 
I have never had an issue with bronze gears in my 30+ years of messing around with crap, but it's always been SBC and BBC, never Fords.
I would put an MSD bronze gear on it and go racing.
Why 20W/50? I used to years ago, then went to Mobil 1 10W/30, engines are 100% perfect. Ask the engine builder. Unless you have really loose clearances I would not be running that oil.
Never saw a distributor gear get ANY wear on the backside, I hope Itey was right in his explanation.

Once you put a crank trigger on there you won't have to worry about the distributor doing anything but spinning the oil pump.

But, if your timing retarding wasn't just the distributor and was also the ignition box, you will soon find out.
 
Took the dogs and went out to try to go mushroom picking as the rains we had last week and the last few days have been pretty warm so I thought for sure they would be out pretty thick by now, we didn't find a single one.

I have never had an issue with bronze gears in my 30+ years of messing around with crap, but it's always been SBC and BBC, never Fords.
I would put an MSD bronze gear on it and go racing.
Why 20W/50? I used to years ago, then went to Mobil 1 10W/30, engines are 100% perfect. Ask the engine builder. Unless you have really loose clearances I would not be running that oil.
Never saw a distributor gear get ANY wear on the backside, I hope Itey was right in his explanation.

Once you put a crank trigger on there you won't have to worry about the distributor doing anything but spinning the oil pump.

But, if your timing retarding wasn't just the distributor and was also the ignition box, you will soon find out.

I thought ignition box too
 
The MSD analog boxes retard timing as rpm goes up. I saw almost 4 degrees on a 6AL. But it honestly did not cost much power on the dyno. Power adders are 100% different though. Better to retard than advance.
Not sure about the digital boxes, never stood next to an engine on the dyno like I did with the analog box. And I really don't want to do that again.........

I also know that on the two different types of boxes they each have their own way of making sure the polarity is correct on the pickup sensor.
You would need to find the info on this procedure, might be on MSD's website.
I think on the analog box you hook up the sensor, start the engine and check the timing.
Now shut it off, reverse the wires, start it up again, check the timing.
Whichever wiring combo gives you the most timing at idle is the correct way to wire it.
People have seen that it isn't always green to green and violet to violet........

I think the digital boxes were the opposite.

Again, find the info, I know it's out there.
 
I have never had an issue with bronze gears in my 30+ years of messing around with crap, but it's always been SBC and BBC, never Fords.
I would put an MSD bronze gear on it and go racing.
Why 20W/50? I used to years ago, then went to Mobil 1 10W/30, engines are 100% perfect. Ask the engine builder. Unless you have really loose clearances I would not be running that oil.
Never saw a distributor gear get ANY wear on the backside, I hope Itey was right in his explanation.

Once you put a crank trigger on there you won't have to worry about the distributor doing anything but spinning the oil pump.

But, if your timing retarding wasn't just the distributor and was also the ignition box, you will soon find out.
Engine builder recommended this oil. Main bearing clearance is .0031".
 
Engine builder recommended this oil. Main bearing clearance is .0031".
Ok, that is why I asked. I do not remember the clearance my stuff was set for, but he knows I wanted to run 10W/30 and it has been perfect for 15 some years of using it.
 
I think you need to have oil temperature of at least 200 F with 20-50. You need to get the oil above the boiling temperature of water to drive the moisture out of it. I liked to see the oil in the 454 in my flatbottom 240+. I usually used Valvoline 20-50 and tried to avoid RPM over 4000 until it was at least 180. You could feel it free up at 240+, as if the water under the boat had less friction or drag. For the BS of purposely running cold oil and water for racing the oil needs to be low viscosity.
 
There is a place 10min from me that has this. I'm going to give it a try. Probably only a couple more TnT dates left if the weather allows.

 
Back
Top