Breaking up at high rpm, carb issues, and converter issues.

As I found out on my build, oil pressure is the enemy oddly enough. I was told 65psi is flirting with disaster.

And composite gear was suggested by almost everyone competent with building sbf engines.

@itey Maybe you know, and I'd like to understand better.. could you explain how a high volume oil pump is bad on a sbf and how it effects distributor gear. I thought I heard race car Ronnie on the phone say something about drilling a hole in the lifter/oil galley plug behind the distributor. At least I think that's what I heard, I was too excited and my ears weren't working
I have that hole drilled. It makes sure the distributor and cam gear are getting lubricated.
 
Wouldn’t this have been total failure with a composite gear? I’ve used a bronze before on a 393 I had and it left me on the side of the road. Because it was gone! No teeth left. All were worn down.
 
Are you sure that gear is melonized? I thought the process left like a textured almost dimpled finish on it and yours looks smooth?
 
Are you sure that gear is melonized? I thought the process left like a textured almost dimpled finish on it and yours looks smooth?
The new Howard’s gear in the picture is a melonized gear. I think if anyone is full of shit, it’s MSD. Maybe the gear that came on the distributor was not melonized.

I was searching a couple days ago and found this.

It is a salt bath Ferritic Nitrocarburize procedure which uses a cyanide base. The process is accomplished at temperature around 1050F. It is usually (but not in all cases) applied to low alloy steels to form a surface generally of iron nitrides.
 
Oil filter looks good to me. Nothing shiny came out and no particles in it. I’m charging a battery for my scope. I was to see if I can get a better view of the cam gear.
 
Wouldn’t this have been total failure with a composite gear? I’ve used a bronze before on a 393 I had and it left me on the side of the road. Because it was gone! No teeth left. All were worn down.
The composite gear would wear better but there's still a problem there and just gear material would not change that
 
Are you sure that gear is melonized? I thought the process left like a textured almost dimpled finish on it and yours looks smooth?
I think you skipped the part where the gear was worn down. Even if it was a melonized gear and had that much wear it would have polished it smooth. Think flap disc.
 
The new Howard’s gear in the picture is a melonized gear. I think if anyone is full of shit, it’s MSD. Maybe the gear that came on the distributor was not melonized.

I was searching a couple days ago and found this.

It is a salt bath Ferritic Nitrocarburize procedure which uses a cyanide base. The process is accomplished at temperature around 1050F. It is usually (but not in all cases) applied to low alloy steels to form a surface generally of iron nitrides.
I don't trust the new gears that come on the MSD Pro billet either, I changed the one off my new distributor for the 582 when I originally put it in because I just did not trust them.
 
I’m about to pull the balancer. Before I install anything, I’m going to see if I can get a closer look at my cam gear. If it looks like it will be ok, the crank trigger is going on.

I have this brand new Howard’s melonized gear, but I’m thinking of returning it for a Bronze gear.
 
I’m about to pull the balancer. Before I install anything, I’m going to see if I can get a closer look at my cam gear. If it looks like it will be ok, the crank trigger is going on.

I have this brand new Howard’s melonized gear, but I’m thinking of returning it for a Bronze gear.
I've never trusted the melonized gears. Bronze is what *always* worked forever in the past and I've never seen a reason to change from it.


*edited due to talk to text grammar mistakes*
 
Last edited:
On another note I have a red distributor cap I took off my msd pro billet because it wasn't a cool color if you need one. Thought I saw somewhere you were going to cut one open
 
On another note I have a red distributor cap I took off my msd pro billet because it wasn't a cool color if you need one. Thought I saw somewhere you were going to cut one open
Might be cheaper for me to buy one from vato zone than for you to ship it. Thanks though. I just need an extra to cut a hole in it to phase the rotor.
 
You need to run a magnet through the drain oil and the pleats in the filter paper. Cut the paper off the metal parts of the filter and stretch it out and drag a magnet around over the filter material. (unless you don't want to know) No way that gear can look like that and there not be steel flack in the oil.
 
The composite gears are not so bad as people think.

Several years ago went a few rounds with a 351W in a fine '69 Mustang, CC hyd roller, don't know about the oil pump, but it ate three bronze gears, all from CC. The 2nd and 3rd were showing rapid wear in just a few miles so were changed immediately. The 4th gear is a composite from CC and it has been in use continually since in the sunny day daily driver / track day toy.

I guarantee the gears were all installed correctly to the depth and shaft end clearance required in FoMoCo specs and the block dimension was double checked.

Because of the circus with the bronze gears we pulled the plastic gear several times in a few miles, few days, few months, and the next two annual oil changes, and not a bit of wear, it literally didn't look like it had been run at all.
 
Fuck. Fuck. And fuck.
Time to start winter planning. I’m thinking to pull it, fix what needs fixing and get it on the dyno. Then send the info to Coan and get the converter just right.

5.79 will have to wait, but I hit my long time goal and been having a blast with the car since August.

All is well.
 
Took the filter apart, ran the magnet. Couple little shiny things, but after running my finger over the magnet I didn’t see or feel anything. I’ll see if the magnets on the oil pan picked anything up when I drain it.
 
Back
Top