Breaking up at high rpm, carb issues, and converter issues.

Post 480 was done properly. I would guess those were lean. Barely any color. Keep in mind this is only 1/8th mile pass. The wideband showed 12.6-13.0.
Honestly, they don't bother me one bit.
You run short or open exhaust?
What color is in the end of the pipe?
 
You can’t make this shit up. I go to start the car an hour ago and it won’t start. Not even a cough. Then it started pouring, so racing is off for today. Nothing in the forecast all week. Morherfuckers.

I have fuel, spark, and compression. I checked all of the valves and everything is good. All I did was change plugs and jets since last week.

Plugs are tq’d and wires are on tight. I’ll open the carb in a minute, but fuel is coming out of the squirters and bowls are halfway up.

Had the wife crank while I moved the distributor and nothing at all. Just cranks.
 
Are you saying it helps to turn on the fuel pump?
 
Are you saying it helps to turn on the fuel pump?
It was only 47* outside. I just kept cranking it and giving it a squirt of fuel every few seconds and it started coughing and finally it lit off.

I got my timing set and then they cancelled the races. Tonight was the last Friday TnT. Now the fucking sun is out. 🤬
 
I pulled my distributor today because the timing seems to be retarding quite a bit. The gear doesn't not look like normal wear to me. I measured the gear spacing in accordance with Ford Racing’s literature that @itey posted.

It is right at the minimum 4.031”, but I feel like something isn’t right.


 
4.031" pulled down or pushed up?

The load of turning the oil pump should be keeping the gears in constant contact and the gear thrust down against the flange in the block.

Measure from the upper distributor flange in the block where the distributor housing seats to the lower flange in the block where the gear thrusts down against. That dimension should be between the minimum and maximum dimensions of the shaft end play, so the shaft is floating in the distributor when the gear is thrust down against the flange in the block.

Nobody needs to tell you that ain't supposed to look like that. The distributor gear material is not compatible with the cam gear.

Now, you need to look close at the gear on the cam and see how tore up it is.

Is the oil pump high pressure or high volume?

Another disturbing clue is evidence of contact on the back side of the distributor gear teeth. That happens when the pump is bound up trying to pump more oil than can flow through the bearing clearances and cannot rotate smoothly and the pulsation causes the hex shaft oil pump drive to twist like a torsion spring and oscillate, causing the gear teeth to chatter against each other and bump the back sides of the gears which ordinarily would never touch if the pump turned smoothly without chattering.
 
It's obvious it's riding right on the tip of the tooth, that's going to affect your timing a lot more than if it was riding all the way down in the saddle.
 
It's eating the gear. Need to cut open the oil filter and play in the pleats with a magnet. I like to use a big sheet of white butcher paper to open a filter on to make the debris and flack easier to see.

If the gear on the cam looks OK (good luck) I would try a composite gear.

How much oil pressure is there?

What kind of oil filter was used?

What weight oil?
 
As I found out on my build, oil pressure is the enemy oddly enough. I was told 65psi is flirting with disaster.

And composite gear was suggested by almost everyone competent with building sbf engines.

@itey Maybe you know, and I'd like to understand better.. could you explain how a high volume oil pump is bad on a sbf and how it effects distributor gear. I thought I heard race car Ronnie on the phone say something about drilling a hole in the lifter/oil galley plug behind the distributor. At least I think that's what I heard, I was too excited and my ears weren't working
 
4.031" pulled down or pushed up?

The load of turning the oil pump should be keeping the gears in constant contact and the gear thrust down against the flange in the block.

Measure from the upper distributor flange in the block where the distributor housing seats to the lower flange in the block where the gear thrusts down against. That dimension should be between the minimum and maximum dimensions of the shaft end play, so the shaft is floating in the distributor when the gear is thrust down against the flange in the block.

Nobody needs to tell you that ain't supposed to look like that. The distributor gear material is not compatible with the cam gear.

Now, you need to look close at the gear on the cam and see how tore up it is.

Is the oil pump high pressure or high volume?

Another disturbing clue is evidence of contact on the back side of the distributor gear teeth. That happens when the pump is bound up trying to pump more oil than can flow through the bearing clearances and cannot rotate smoothly and the pulsation causes the hex shaft oil pump drive to twist like a torsion spring and oscillate, causing the gear teeth to chatter against each other and bump the back sides of the gears which ordinarily would never touch if the pump turned smoothly without chattering.
Pushed up (pulled apart). Cam manufacturer said a melonized gear would be fine. I have an MSD pro -billet distributor. I called MSD and they said it was a melonized gear on it already. I relayed that to the cam manufacturer and he said, “you’re good to go then”.

The cam gear doesn’t look bad, no where near what the distributor gear looks like. It’s a standard volume melling oil pump.

Oil pressure is about 40 at idle. 50 during the pass, drops to 25 on the shift and then goes back to 50.
 
It's obvious it's riding right on the tip of the tooth, that's going to affect your timing a lot more than if it was riding all the way down in the saddle.
I knew something was up with timing, that’s what told me to pull it out. I think I found out where my 2mph went.
 
It's eating the gear. Need to cut open the oil filter and play in the pleats with a magnet. I like to use a big sheet of white butcher paper to open a filter on to make the debris and flack easier to see.

If the gear on the cam looks OK (good luck) I would try a composite gear.

How much oil pressure is there?

What kind of oil filter was used?

What weight oil?
I will cut the filter open. I think I answered all of the other questions except oil weight. I’m using Schaeffer’s

Edit: Wix Racing oil filter.
 
Last edited:
Back
Top