Breaking up at high rpm, carb issues, and converter issues.

Also, why does he say it’s at 10, when it looks like 5? Both directions 10 is in the same place. 🤷🏻‍♂️
The very first sentence in the post is: "Here is a video showing the electronic slew rate retard characteristic of all analog ignition amplifiers, induction or CD. Crankshaft degrees are 2 times distributor degrees shown on the distributor machine."
 
I kind of explained it in post #521. I’m caught up chasing 5.79 right now. I got a late start to the season due to getting screwed by an engine shop, so the car is pretty dialed in right now other than losing the 2mph and tenth or two.

I’m entering the last big bracket next weekend and then it’s TnT for the rest of the year. I probably won’t do well since I have not focused an ounce of effort towards my reaction times.

My whole life I’ve always just chased the best possible e.t. That I could get with my particular combo. I’m caught up in that right now. I keep telling myself that if I could hit that 5.79, I can focus my attention on other stuff.

To your point, I lost how relatively consistent the car is. It’s not duplicating slip after slip, but even while making changes it’s pretty consistent. Case and point here are all my passes while making changes Friday…

1. 5.920@115.71
2. 5.895@116.92
3. 5.917@116.84
4. 5.916@116.10
5. 5.892@116.46

You have the same disease that most everybody has. 😄

I traded a VERY consistent & race winning 7.0 car for this roadster

I built it thinking if it just went 5.99 I’d be happy. When it went 5.83 I thought a .79 would be good. When it went .74 I thought a .69 would make me happy. When it went a .65 I thought a .59 would make me happy. I set it up to go .59 in killer air & missed it dam near melting the tips off the plugs. If I spent another $2000 on a bigger carb & looser converter it would do it but there’s no point & with my luck it’d go a .54 setting up the next goal of a .49. 🤦‍♂️

I think this is why folks get disgusted with it, chasing the ego thing.
 
The very first sentence in the post is: "Here is a video showing the electronic slew rate retard characteristic of all analog ignition amplifiers, induction or CD. Crankshaft degrees are 2 times distributor degrees shown on the distributor machine."
See post 513
 
Liking the idea of the crank trigger.

Also, like others have mentioned, lot's of good discussion and knowledge to be learned here, and other threads like this one. Without throwing darts at the blue oval, which I am guilty of regularly, the hot rod in this case is clearly a stout running machine, and issues that I would normally not consider due to ignorance of the Ford design could be a cause. I would never think for a minute that my distributor gear was wearing in a chevy. Learning new stuff is ALWAYS a bonus!

As far as the 2 degree retard goes......if your timing is sitting where you made the last move and nothing picked up, but nothing slowed down, a 2 degree retard is not likely to be easily measured by time slips.

When trying to seek every ounce of potential from a drag car, it is really tough, and maybe even impossible without a ton of data acquisition.

I have tried both ways, and it sure makes things clear in a hurry when you spend yourself into a headache with grids, and a pile of racepak stuff.

Before having that stuff, I would simply play with jetting, timing, and an occasional plug check, and all of my decisions were made from my only source of data......a timeslip. Max ET was the goal, let the MPH land where it may, and as long as it repeated consistently, I would give the old girl new plugs every spring.....just because. When I got the coupe, we trial and errored that thing until the cows came home. It was fast, but inconsistent much of the time. I finally opened up the wallet and went to a grid, racepak, and top end shocks, with shock sensors. The journey got boring in a hurry after that. It took maybe two limited run trips to the track for me and Bangr to pin the setup down.

Granted, your ponycar is not in the same ET range as my junker, but considering it is a smallblock, small tire car, that thing is hauling ass. You have enough power to make it finicky.

I have no doubt you will get this thing lined out PR, due to your willingness to make it happen. Just keep this in mind......if you had a .75 to 1 second to the 1/8 slower car, most of the issues you are dealing with would not be there. From my personal experience, you have crossed the power/ET line that makes issues appear because the entire package is not 100% perfect. With 100 less horsepower, the inconsistent wheel speed at the line would vanish. At slower ET's, a dead hook is normal and perfectly fine.

This stuff can be mentally exhausting, but once in a while you have to back up and objectively assess just how far you have come recently. You are doing GREAT! Keep making educated decisions on changes, and don't let a lack of immediate returns get you down. You are really close to the max potential with the current package, it is jut a matter of making it work more regularly.
You nailed it on the head Mitch, he stepped into the realm of creating problems by eliminating others and when it all boils down to it that's why we love this. It's the problem solving aspect.
At least for me it is.

Keep chipping away at it as you're doing a damn good job and inspiring for a lot of people here, myself included.
 
everyone is always concerned with more magnets equaling more accurate and precise control
A/B/A test on dyno with a 500 between the 4 mag and a 36-1 was nothing measurable power wise
Im sure with in cylinder combustion analysis a person may be able to find something? But i didnt see it
My ls i went from 58x to 12-1
again, i saw nothing, except the 58X would shut off above about 8800 rpm due to the sensor being a cunt...lol
I had a similar issue with my engine when I had the Holley 60-2 setup. It worked great till.......... Many times around 7000 or above it would drop out. You know the scoop. Tried different sensors, different gaps, no beuno! Some people were welding two wheels together to help keep them from vibrating. With the BBC that balancer is pretty large so that trigger wheel had a lot of meat to sit against. On a SBC the wheel was larger than the balancer. We believe the wheel would simply start vibrating and the sensor would not get triggered by the teeth.

But, it was a really cool setup. I have 4 coil packs recessed in my firewall, I did a nice job with those. They operate waste fire, as one cylinder is under compression and needs the spark, the other cylinder is on the exhaust stroke and doesn't need the spark, but gets it anyway. Many OEM cars had this stuff until they started doing CNP (individual coil packs). With my setup and software if you wanted to adjust timing on a cylinder then it's mate also got adjusted and you just dealt with it. But damn that timing mark did not move! Engine looked like it was off. My wheel has 2 teeth missing out of the 60. That is how it knew when #1 was coming up and could do the correct firing order.

Well, Holley had me put a "normal" 4 magnet MSD trigger wheel on there and I am using their Hall Effect sensor, not the VR sensor that came with the MSD setup. But in doing so I had to put a camshaft sensor in there so the EFI knew when #1 was coming around, so I have a cam sync setup in there for that, and to drive the oil pump. I have been to 8600 rpm with this setup, flawless. The timing is still pretty darn steady, but not like the 60-2 wheel, but that's fine, it runs perfect.

I have no need nor desired for individual coil packs unless I get back into nitrous, this works fine. My coil packs can be bought at a parts store if I am desperate, they came off a 2002 or so S-10 with the 4 cylinder engine. Probably used in other applications too. The Buick Grand National packs look the same as mine too.
 
WTF, so how does giving it advance stop it from retarding? So if I put the weights, springs, and donut back in, it isn’t going to retard the timing?

Why wouldn’t it?
Until it reaches the total and hits the stop at whatever RPM, mechanical advance compensates for the box retard, but the box retards from that point on as RPM goes up.

The advance mechanism can be modified to have an advance rate over the entire RPM range that compensates for the box retard and keep the timing steady or advance as desired as RPM increases.

A problem with advance mechanism limited by a hard positive stop is it can bounce on the stop and cause the timing to scatter. An advance mechanism calibrated to run on the weights and springs to beyond engine maximum speed can prevent that while it provides the most desirable advance over the total RPM range. The problem is that ain't easy without a distributor machine and a lot of patience, and most people have neither. The programmable digital box will do this for anyone willing to take the time to figure out what their engine wants.

For bracket racing none of this matters much when a consistent ET slip is most important, however that is obtained. In a field of cars on an oval or road course that have a similar engine or crate engine rule, the one with the correct ideal advance curve will have an almost unfair advantage over the others that have locked advance.
 
@Mike Beck

Better late than never. Are these 8’s looking too cold? Barely 2 threads look dull. This is plug #1 with two 1/8th mile passes.


 
Here is plug#8. This plug has five 1/8 mile passes on it. Is that where timing should be? It’s easier to see on #8 because it got me heat in it since I never pulled it. Not sure what all that junk is. Could be anti-seize that I couldn’t clean out of the hole.


 
Cut that first plug open so we can see the fuel ring. I think the timing is close, the timeslip will tell you if you need more or less. I move 2* at a time, you aren't going to hurt it and we only get so many passes a day at the track. That is why I like chassis dynos, can do a lot of testing in a few hours to get a good idea what it wants. But......... we always find that the best power on the chassis dyno is typically 2* or so too much timing at the track. But, we race 1/4 mile so things are different for us. That second half of the track makes a lot of heat in the chambers!
 
Cut that first plug open so we can see the fuel ring. I think the timing is close, the timeslip will tell you if you need more or less. I move 2* at a time, you aren't going to hurt it and we only get so many passes a day at the track. That is why I like chassis dynos, can do a lot of testing in a few hours to get a good idea what it wants. But......... we always find that the best power on the chassis dyno is typically 2* or so too much timing at the track. But, we race 1/4 mile so things are different for us. That second half of the track makes a lot of heat in the chambers!
Is it worth cutting even though it had idle time, driving to and from staging, and two 1/8th mile passes?
 
Sure, it's good practice for you! :)
I can see part of the fuel ring in one of the pictures. The porcelain doesn't look that bad for what you said the plug has been through.
 
Sure, it's good practice for you! :)
I can see part of the fuel ring in one of the pictures. The porcelain doesn't look that bad for what you said the plug has been through.
How does the heat range of the plug look? One of the plugs has basically only one thread dull. Number 8 which went 5 passes only has 2.
 
I never looked closely at my plugs running N/A.
But on the bottle, I would get heat into the first two threads, that was good. The heat in the strap would be almost to the bend.
This is on an NGK plug like yours.
If I pushed the timing to the bend, or past, it would slow down.
Again, that was my combination.
Many others would see gains all the way to the bend, or past. But we are only talking a few mph.
In our case, we had no limit to jet size so why push the timing to go faster when we could just change the jet sizing........

Those plugs are fat, but not terrible. If you can, warm the car up, put a couple of new plugs in, especially one of the corner plugs, drive it up to the lanes. Now pull one and see if you colored it at all. I always used my driving gloves, they really protect your hands from heat. Far better than Mechanix gloves!

Now stick that plug back in unless you find you really made a mess of it in which case your carb needs a lot of attention. Make the pass, kill the ignition after the traps and lift off the throttle at the same time. I also throw the Glide into neutral and since I have a Pro Brake it is a nice and easy movement and with my Winters shifter there is no danger of putting it into reverse.

Get on the return road out of the way and go pull those two plugs and stick two spares in there and drive it back. Now you have something clean to look at. If you can see down inside then you don't have to cut them open, but you really don't need to do this too much. Once you see a good fuel ring you will know the A/F your engine wants to run. I am betting 13.0 to 13.6 A/F is going to look nice and run just fine on that engine with that fuel. The higher the octane then leaner you will run it to keep the power the same. I would lean out my engine .2 A/F when the track didn't have Sunoco Blue and I had to run Red instead. Ran the same ET/MPH and the EGT's were the same once I leaned it out that little bit. Just cost $1 a gallon more.
 
I never looked closely at my plugs running N/A.
But on the bottle, I would get heat into the first two threads, that was good. The heat in the strap would be almost to the bend.
This is on an NGK plug like yours.
If I pushed the timing to the bend, or past, it would slow down.
Again, that was my combination.
Many others would see gains all the way to the bend, or past. But we are only talking a few mph.
In our case, we had no limit to jet size so why push the timing to go faster when we could just change the jet sizing........

Those plugs are fat, but not terrible. If you can, warm the car up, put a couple of new plugs in, especially one of the corner plugs, drive it up to the lanes. Now pull one and see if you colored it at all. I always used my driving gloves, they really protect your hands from heat. Far better than Mechanix gloves!

Now stick that plug back in unless you find you really made a mess of it in which case your carb needs a lot of attention. Make the pass, kill the ignition after the traps and lift off the throttle at the same time. I also throw the Glide into neutral and since I have a Pro Brake it is a nice and easy movement and with my Winters shifter there is no danger of putting it into reverse.

Get on the return road out of the way and go pull those two plugs and stick two spares in there and drive it back. Now you have something clean to look at. If you can see down inside then you don't have to cut them open, but you really don't need to do this too much. Once you see a good fuel ring you will know the A/F your engine wants to run. I am betting 13.0 to 13.6 A/F is going to look nice and run just fine on that engine with that fuel. The higher the octane then leaner you will run it to keep the power the same. I would lean out my engine .2 A/F when the track didn't have Sunoco Blue and I had to run Red instead. Ran the same ET/MPH and the EGT's were the same once I leaned it out that little bit. Just cost $1 a gallon more.
That is exactly what I did last week. The 2nd set of plug pics from last week. The two plugs that look almost the same.
 
If that is all you did on those plugs you need to lean it out.
So simple on EFI. I don't know how much jet you need to pull, but if the air is the same the next time you go out, I would drop 2 sizes all the way around.
 
If that is all you did on those plugs you need to lean it out.
So simple on EFI. I don't know how much jet you need to pull, but if the air is the same the next time you go out, I would drop 2 sizes all the way around.
Are you confusing the first pics I posted with the ones from yesterday? The two from yesterday were not done with proper shut down.
 
Are you confusing the first pics I posted with the ones from yesterday? The two from yesterday were not done with proper shut down.
The plugs from post 537 & 537 had a lot of passes on them and strange stuff all over the place. I wouldn't really want to use those for any tuning decisions.
The plugs from post 542 is what I was calling fat.
You want it lighter, a brown color, not black.

This has nothing to do with you, and I don't know what Bob has seen on the Pro Stock stuff, but the high power Pro Mods and similar cars with nitrous have the plugs come out looking as clean as they went in. Many times the fuel ring is barely visible. It is strange to see it, but it works. Again, nothing to do with us with N/A engines and no N2O feeding it. All they really see is heat on the straps and the threads at the end of the plug.
 
The plugs from post 537 & 537 had a lot of passes on them and strange stuff all over the place. I wouldn't really want to use those for any tuning decisions.
The plugs from post 542 is what I was calling fat.
You want it lighter, a brown color, not black.

This has nothing to do with you, and I don't know what Bob has seen on the Pro Stock stuff, but the high power Pro Mods and similar cars with nitrous have the plugs come out looking as clean as they went in. Many times the fuel ring is barely visible. It is strange to see it, but it works. Again, nothing to do with us with N/A engines and no N2O feeding it. All they really see is heat on the straps and the threads at the end of the plug.
Post 480 was done properly. I would guess those were lean. Barely any color. Keep in mind this is only 1/8th mile pass. The wideband showed 12.6-13.0.
 
Back
Top