Breaking up at high rpm, carb issues, and converter issues.

Jesus christ every time i buy something i swear the same day you guys are talking about it failing.

Guess I'll toss my yellow top in the trash that i got today!

@Patriot Racer those plug wires look fat as fuck!
 
Jesus christ every time i buy something i swear the same day you guys are talking about it failing.

Guess I'll toss my yellow top in the trash that i got today!

@Patriot Racer those plug wires look fat as fuck!
They are only 8.65mm, but have a Kevlar sleeve that makes them look bigger.
 
After changing the master kill switch, which was legitimately harder than swapping engines in that car, changing the coil, the ignition box, distributor, and eliminating the transbrake and delay box, it turned out to be a 28 dollar Ford solenoid mounted on the firewall. One of the main power posts broke inside the plastic housing. It would make contact sitting still or doing a burnout, but when I would launch the car it would pull apart killing the power to the car. It would then close back up, then pull apart, etc. until we got far enough down track that we would be below 2G's acceleration, then it would stay contacted and pull like normal the rest of the run.

I am still remembering stuff.......changed the fuel pump and rebuilt the carbs twice as well.
Were you using it to kill main power in the car?
The "normal" Ford starter relay is a momentary type, though in a Drag Racing application it might survive being used like that.
I have installed Constant Duty solenoids in some cars that needed them to kill main power in the car. They are made for it, just like Golf Carts and large winches. But they pull a LOT of power! I tell the people using them that they MUST turn off the battery switch when the car is not being used, even on race day.
 
Were you using it to kill main power in the car?
The "normal" Ford starter relay is a momentary type, though in a Drag Racing application it might survive being used like that.
I have installed Constant Duty solenoids in some cars that needed them to kill main power in the car. They are made for it, just like Golf Carts and large winches. But they pull a LOT of power! I tell the people using them that they MUST turn off the battery switch when the car is not being used, even on race day.

Not used to kill power. Just a regular 4 post HD Ford style starter solenoid.

Master kill switch located immediately after batteries in rear of car. Battery cables come up front from the master kill switch to the solenoid. From solenoid to starter. 10 gauge jumper wire to power a small post with a 12 gauge wire going to the ignition switch.

My power is rarely on in the car. I have a slick cable system from a chute lever mounted on the side of the shifter that ties into the master kill in the rear of the car. The power can be killed by the push switch in the back, or I can turn it on and off from the drivers seat, and that is where it is controlled from 99% of the time.

My guess is that the solenoid failed from a rare tire shake. I am glad you brought this subject up because I just did a google search and found much stronger looking starter solenoid that are entirely metal on the outside and made for racing applications. They cost about 4x as much, but I am guessing that tire shake will be a lot more common with my new combination.
 
Not used to kill power. Just a regular 4 post HD Ford style starter solenoid.

Master kill switch located immediately after batteries in rear of car. Battery cables come up front from the master kill switch to the solenoid. From solenoid to starter. 10 gauge jumper wire to power a small post with a 12 gauge wire going to the ignition switch.

My power is rarely on in the car. I have a slick cable system from a chute lever mounted on the side of the shifter that ties into the master kill in the rear of the car. The power can be killed by the push switch in the back, or I can turn it on and off from the drivers seat, and that is where it is controlled from 99% of the time.

My guess is that the solenoid failed from a rare tire shake. I am glad you brought this subject up because I just did a google search and found much stronger looking starter solenoid that are entirely metal on the outside and made for racing applications. They cost about 4x as much, but I am guessing that tire shake will be a lot more common with my new combination.
Put a Coyote in there, won't have enough power to shake or turn a large slick........

Ha ha!

Gotta take a poke at the Ford nuts! :)

Went through something like tire shake once with the wifeys car. Broke the ring and pinion in the 60ft. Whopping 11 second car at the time. Well, that is the first time I ever smashed my teeth together. The visors came down, didn't know she had time slips and shit on top of them, that stuff came flying down. Rear view mirror fell off the windshield. Was actually pretty damn funny to see all the shit flying around. But damn my teeth HURT!

Yes, it was a stock GM 7.5 rear in her 89 TA. After that it got a Ford 9" like mine.
 
Put a Coyote in there, won't have enough power to shake or turn a large slick........

Ha ha!

Gotta take a poke at the Ford nuts! :)

Went through something like tire shake once with the wifeys car. Broke the ring and pinion in the 60ft. Whopping 11 second car at the time. Well, that is the first time I ever smashed my teeth together. The visors came down, didn't know she had time slips and shit on top of them, that stuff came flying down. Rear view mirror fell off the windshield. Was actually pretty damn funny to see all the shit flying around. But damn my teeth HURT!

Yes, it was a stock GM 7.5 rear in her 89 TA. After that it got a Ford 9" like mine.

Ya, I have zero point zero inches of timing chain, and I am fine with that.:thumbup:
 
I made some really good progress today. I started from scratch thinking maybe the old wideband was not reading correctly, but it was. Hard to see, but it was.

With that said, I had to make a lot of jet changes tonight. Air was shitty too. DA was 3000 on the first pass and 2450 on the last pass.

Jets from BLP were .106 primary and .118 secondary. With 4.5 power valve.
First pass was 6.13 @ 113 and I was seeing 11’s for AFR. Car was still breaking up. That 4.5 PV was acting funny while cruising in the pits, I could feel it and see it on the AFR gauge.

I started taking jet away and AFR was getting better, but car was still breaking up. Mark from BLP actually called me to find out how it was going and gave me some pointers. Who does that?! These guys have a customer for life. Mark told me to throw that 2.5 power valve in and I did. I immediately saw improvement with part throttle, just felt cleaner.

Long story short I got my AFR dialed in to 12.7 with .092/.104 jets. I also bumped my rev limiter to 8500 to see if it would stop breaking up and it did.

Last 2 passes of the night were
6.01 @ 115.63 (spun a little) 1.37 60’
6.00 @ 115.29 1.34 60’ (DA 2450)

No 5’s today, but a lot of progress was made. I’m getting close on the tune and now I know the box is acting up. The 7AL-2 will be going in this weekend.

I still have a degree or two of timing to play with and the converter is still only flashing to 5500.
 
Last edited:
I made some really good progress today. I started from scratch thinking maybe the old wideband was not reading correctly, but it was. Hard to see, but it was.

With that said, I had to make a lot of jet changes tonight. Air was shitty too. DA was 3000 on the first pass and 2450 on the last pass.

Jets from BLP were .106 primary and .118 secondary. With 4.5 power valve.
First pass was 6.13 @ 113 and I was seeing 11’s for AFR. Car was still breaking up. That 4.5 PV was acting funny while cruising in the pits, I could feel it and see it on the AFR gauge.

I started taking jet away and AFR was getting better, but car was still breaking up. Mark from BLP actually called me to find out how it was going and gave me some pointers. Who does that?! These guys have a customer for life. Mark told me to throw that 2.5 power valve in and I did. I immediately saw improvement with part throttle, just felt cleaner.

Long story short I got my AFR dialed in to 12.7 with .092/.104 jets. I also bumped my rev limiter to 8500 to see if it would stop breaking up and it did.

Last 2 passes of the night were
6.01 @ 115.63 (spun a little) 1.37 60’
6.00 @ 115.29 1.34 60’ (DA 2450)

No 5’s today, but a lot of progress was made. I’m getting close on the tune and now I know the box is acting up. The 7AL-2 will be going in this weekend.

I still have a degree or two of timing to play with and the converter is still only flashing to 5500.
I’m no expert, maybe I’m the worst. At least here at work, lol. But I want to see your 60s improve. Going off my times I remember you have a tenth in it if you get down to 1.31 area where I hit a couple times. And I’m way slower in 1/8 at a best of like a 6.10.
 
I’m no expert, maybe I’m the worst. At least here at work, lol. But I want to see your 60s improve. Going off my times I remember you have a tenth in it if you get down to 1.31 area where I hit a couple times. And I’m way slower in 1/8 at a best of like a 6.10.
You’re right, but I have not focused much on that yet. I think I could get a little more out of it. However, if the converter was right, I think I could get into the 1.29’s.
 
I also realized yesterday that I have a decision to make with rear gears. I have a relatively low SLR with the glide/29”tires/4.71’s, and I can’t make it to the end of the 1/4 mile.

I’ve been racing 1/8th mile forever and it’s easier on the car/parts.

If I put 4.30’s in it, I would likely make it to the end of the quarter, but at what cost? Won’t it “loosen” the converter raising stall? But at the same time lowering SLR even more?

If I gear it for the 1/8th the SLR will be better, but converter will likely stall lower correct? Sounds like either way I go, the converter might now be optimal.
 
I also realized yesterday that I have a decision to make with rear gears. I have a relatively low SLR with the glide/29”tires/4.71’s, and I can’t make it to the end of the 1/4 mile.

I’ve been racing 1/8th mile forever and it’s easier on the car/parts.

If I put 4.30’s in it, I would likely make it to the end of the quarter, but at what cost? Won’t it “loosen” the converter raising stall? But at the same time lowering SLR even more?

If I gear it for the 1/8th the SLR will be better, but converter will likely stall lower correct? Sounds like either way I go, the converter might now be optimal.

How high can you spin your motor? According to Wallace Racing Calculator you should be just under 7750rpm in high gear @ 142mph, which is where I guessed your 1/4 mile speed to be. Pretty sure their program does NOT factor in any tire growth either.
 
A few things here,

I need to pay more attention while posting and I'm an idiot. 🤦
 
Last edited:
4.30 gears should put you @ 7075rpm at the same 142mph.

How much does your car weigh?
What rpm are you on the two step at?
Have you noticed how many rpm you fall back on the shift?
 
How high can you spin your motor? According to Wallace Racing Calculator you should be just under 7750rpm in high gear @ 142mph, which is where I guessed your 1/4 mile speed to be. Pretty sure their program does NOT factor in any tire growth either.
I guess that is the question of the day, or maybe a better question is how high am I willing to spin it?

I’m not a big budget guy and I’m pretty tapped out. I have a scar forged crank, forged I beams, and forged JE pistons in a dart sportsman block.

I was thinking to set a new shift point of 7500 and rev limiter at 8000 because it seems the car was still pulling last night on the last two passes shifting at 7100-7200.
 
I guess that is the question of the day, or maybe a better question is how high am I willing to spin it?

I’m not a big budget guy and I’m pretty tapped out. I have a scar forged crank, forged I beams, and forged JE pistons in a dart sportsman block.

I was thinking to set a new shift point of 7500 and rev limiter at 8000 because it seems the car was still pulling last night on the last two passes shifting at 7100-7200.
I would try to keep it under 8,000 for sure. It will be easier on parts and while those are decent parts they're not ones that like to be strung out over 8,000 regularly.
 
And just for the record when I said those are decent parts I wasn't meaning they are bad by any means, it's just that they are not all billet ProMod hemi stuff that is designed to spin 10,500 every pass.

I have JE pistons & a mid line crank as well.
 
A few things here,
First off congratulations on your success yesterday. Chipping away at it is not always fun and honestly is quite frustrating at times but you're doing it and being successful at it. I'm proud of you dude!

Okay now what I am seeing is that anti-roll bar in the rear would definitely help your consistency and your 60 ft.
I would also switch down to a 4.30 gear or even try a 4.10 (Not sure if you're going to stay on 29s or drop down to 28s ever for any shootout stuff)

I would send the converter back only after you change to the gear you intend to run.

If you have a GoPro or any other camera try to mount it under the car to watch forward onto the rear suspension. Mounted inside the rear bumper area or somewhere so we could see what the chassis is doing during the launch and at the shift.

Once the rear gets squared away then it's time to move the camera to the front unless you have two of them to see what the front suspension is doing and if it can get any further tuning as well.

You doing a damn good job of troubleshooting this and while I know it's frustrating as hell you are getting it and winning the battle!
Thanks Darren! I think you got me confused with @kwplot34 . I have an anti-rollbar. I also have a GoPro case already set up under the car. I just haven’t focused on that aspect of the tuning process yet. I wanted to get the engine dialed in first then worry about suspension.
 
4.30 gears should put you @ 7075rpm at the same 142mph.

How much does your car weigh?
What rpm are you on the two step at?
Have you noticed how many rpm you fall back on the shift?
1. Car weighs 2670 lbs. with me in it.
2. ing at 5000 converter flashes to 5500
3. Fallback is 1000 rpm
 
Thanks Darren! I think you got me confused with @kwplot34 . I have an anti-rollbar. I also have a GoPro case already set up under the car. I just haven’t focused on that aspect of the tuning process yet. I wanted to get the engine dialed in first then worry about suspension.
Fuck, you're right!
I guess I shouldn't be trying to reply to the forum, Read maps, look for a bear, try to find a timber sale and drive at the same time. God damn
 
Back
Top