Breaking up at high rpm, carb issues, and converter issues.

Fuck, you're right!
I guess I shouldn't be trying to reply to the forum, Read maps, look for a bear, try to find a timber sale and drive at the same time. God damn
He actually text me the other night while he was at the track and told me his car was squatting, first thing I asked was if he had an ARB.
 
1. Car weighs 2670 lbs. with me in it.
2. ing at 5000 converter flashes to 5500
3. Fallback is 1000 rpm
Fallback is good, 1000 to 1200 is what you want.
Stall is no good.
Your combo is very similar to mine, you want that stall around 6400 to 6600.
Mine will hit that stall leaving off the footbrake at 3000 all day long.
The trans brake does very little except help reaction time and hurt my back. ;)

@mcgyver racing He is running a Glide, can't compare 60 ft times between a Glide and a 3 Speed, they will be .1 different yet the same in the 1/4. I have done back to back with my own car. The Glide also hurts the reaction time, thus the reason I have to deep stage, even to go 8.90.

When I was doing my 8.90 stuff my 60s were in the mid to low 1.3x range. I have been 1.26 yet only going 9.00.
Glides are VERY efficient, while you lose ET in the 60 and 300 (or gain, depends which way you want to describe it), you will run the same ET and MPH at worse case, and with the right convertor you will run quicker and faster. It really shows after the 300 how much less power it sucks from the engine, especially when comparing a TH400 and a Glide like I did. I was .1 quicker and 2mph faster with just a trans/convertor swap.
 
I guess that is the question of the day, or maybe a better question is how high am I willing to spin it?

I’m not a big budget guy and I’m pretty tapped out. I have a scar forged crank, forged I beams, and forged JE pistons in a dart sportsman block.

I was thinking to set a new shift point of 7500 and rev limiter at 8000 because it seems the car was still pulling last night on the last two passes shifting at 7100-7200.

In a maxed out heads up car, keeping the motor as high in the rpm band as possible is the key. In a car at your level if you are hunting every .001 of ET it is important to shift it 400-500rpm over peak HP, and fall back to max torque RPM.

Keep in mind that a convertor is not just about where it flashes to. They can be made to flash low, but fall back way to far on the shift, or visa versa.

Sure happy to hear you are in the ballpark now, and that BLP is being so helpful. They were a very good company to work with when I was buying new jets for my carbs.

Where you are at right now is where I have the absolute most fun running a drag car. Already able to make runs, so now it is just figuring out how to wring EVERYTHING out of the combo without getting stupid and hurting parts. FWIW......back when I was running my pickup truck, my really old 482bbc was still running the same factory gen IV block, crank, and connecting rods that I started out with over thirty years earlier. It did grow from a 461 in steps, but the new bore size and pistons got the same old rods and crank every time, and I would spin that poor thing to 8000rpm more often than I should have. lol

Given your MPH, I firmly believe you will see a 5.9x pass several times before the season is over!
 
In a maxed out heads up car, keeping the motor as high in the rpm band as possible is the key. In a car at your level if you are hunting every .001 of ET it is important to shift it 400-500rpm over peak HP, and fall back to max torque RPM.

Keep in mind that a convertor is not just about where it flashes to. They can be made to flash low, but fall back way to far on the shift, or visa versa.

Sure happy to hear you are in the ballpark now, and that BLP is being so helpful. They were a very good company to work with when I was buying new jets for my carbs.

Where you are at right now is where I have the absolute most fun running a drag car. Already able to make runs, so now it is just figuring out how to wring EVERYTHING out of the combo without getting stupid and hurting parts. FWIW......back when I was running my pickup truck, my really old 482bbc was still running the same factory gen IV block, crank, and connecting rods that I started out with over thirty years earlier. It did grow from a 461 in steps, but the new bore size and pistons got the same old rods and crank every time, and I would spin that poor thing to 8000rpm more often than I should have. lol

Given your MPH, I firmly believe you will see a 5.9x pass several times before the season is over!
Thanks, so it sounds like I should bump the shift point to 7500. 😁

I was also wondering if the new ignition is going to allow the car to make slightly more power if the old one is weak. We shall see on that. I was going to start that install today, but I bought a mounting bracket for the 7AL and it doesn’t look like it’s going to be here until Monday. ☹️
 
1. Car weighs 2670 lbs. with me in it.
2. ing at 5000 converter flashes to 5500
3. Fallback is 1000 rpm

Several things can affect "flash". I agree with Mike that higher than 5500 would likely be better for your combo. If it were me, I would try chipping the launch to 4500, maybe even 4000 just for informational purposes. That will probably slow your reaction times a tic, but hitting the convertor harder might help you get the car moving better down low. Convertors are funny critters. Most times what I described above helped me, but I had to raise two step rpm in my coupe to 6000 in order to get it moving out best down low with a 6600 flash......
 
Thanks, so it sounds like I should bump the shift point to 7500. 😁

I was also wondering if the new ignition is going to allow the car to make slightly more power if the old one is weak. We shall see on that. I was going to start that install today, but I bought a mounting bracket for the 7AL and it doesn’t look like it’s going to be here until Monday. ☹

The new ignition might make a difference for sure.

I tested shift points on my old pickup truck that ran exactly where you are now.

6500rpm it slowed down.
7000rpm was almost optimal.
7300 seemed to be a few .00x's quicker, maybe?
7500 and 8000rpm shifts(th400)were exactly the same as 7000, so I went with 7000 because it was easier for me to consistently hit the shift on a big number on the tach face.
 
Here is my best pass to date from last night. Looks like there is more in the suspension, but the converter doesn’t sound right to me, which we already established.

@Mitch H, I tried the lower launches and it still only flashed to 5500. However, now that it is a little more dialed in I can experiment with that again. We raised the launch rpm from 4000 to 4500, and then to 5000, but that’s when it was pig rich.
 
1rd of all congratulations on running 6.0 pretty much right out of the box. That’s around 9.35 which is hauling ass.

Each engine has its own torque & hp curve & that’s why a good converter guy wants to see the dyno sheets. They still manage to get it right by the 2rd or 3th try. lol

I’d keep fiddling with it until it repeats 3-4 passes. You’re somewhere close to it. After it repeats, point the go pro at the tach & make a coupla more passes. You’d be surprised at the difference between a quick peek while driving & what the videro actually shows. THEN hit the converter guy with the videro & let him make his adjustment.


I see too much anti squat & a little too much rear spring as it sits now & it has a mini bounce about 4ft out that’s costing you. That may be what it wants when it’s making all the power it’s gonna & the converter gets right. Probably not but you never know till you full send it.

Keep digging.
 
1rd of all congratulations on running 6.0 pretty much right out of the box. That’s around 9.35 which is hauling ass.

Each engine has its own torque & hp curve & that’s why a good converter guy wants to see the dyno sheets. They still manage to get it right by the 2rd or 3th try. lol

I’d keep fiddling with it until it repeats 3-4 passes. You’re somewhere close to it. After it repeats, point the go pro at the tach & make a coupla more passes. You’d be surprised at the difference between a quick peek while driving & what the videro actually shows. THEN hit the converter guy with the videro & let him make his adjustment.


I see too much anti squat & a little too much rear spring as it sits now & it has a mini bounce about 4ft out that’s costing you. That may be what it wants when it’s making all the power it’s gonna & the converter gets right. Probably not but you never know till you full send it.

Keep digging.
Appreciate the props and input. The anti-squat is high, good observation! It’s over 130%. I can bring that down with a bar adjustment, but it will push my instant center out. I’ll play with my program later to see what my options are.

I have my Viking double adjustable front struts set at 12 compression and 0 rebound (full loose). I have not touched it since the beginning as I didn’t want it to skew my tuning of the engine.
 
Also, talked to Toby (Vigilante Performance) today and he thinks 34* timing might be too much. It’s always been my experience that I’ve ran best at 34-36*.

He explained that better heads = more efficient = less timing. Did a quick search and threads from yellow bullet came up and I was surprised to see so many posts with guys only running 27-33* in combos very similar to mine.
 
Also, talked to Toby (Vigilante Performance) today and he thinks 34* timing might be too much. It’s always been my experience that I’ve ran best at 34-36*.

He explained that better heads = more efficient = less timing. Did a quick search and threads from yellow bullet came up and I was surprised to see so many posts with guys only running 27-33* in combos very similar to mine.
Bob can answer this way better than me, but.....I agree that more efficient heads tend to want less timing, but I think the total combo is the final determining factor. I am most familiar with big block chevy stuff, and have owned motors that wanted 38 degrees, and motors that wanted 27 degrees, and everything in between those numbers. Just helped on a dyno of a 584ci bbc a couple of months ago. The dyno and the plugs both said 40 degrees was the magic number. Your combo might prefer a lot less?

Never had the pleasure of speaking with Toby, and I have no doubt he is a very knowledgeable guy! That said, @Mark O'Neal has stated more than once that they are not fond of well tuned engines.:lmao:
 
How's valve spring pressure? Know it's all fresh. My Mustang has a set of Moroso Blue Max wires that were on my Camaro from back in the 90s. I took them off chasing a drop in performance and when they didn't fix it I saved them for projects in the works. New set was Ultra 40s.
 
How's valve spring pressure? Know it's all fresh. My Mustang has a set of Moroso Blue Max wires that were on my Camaro from back in the 90s. I took them off chasing a drop in performance and when they didn't fix it I saved them for projects in the works. New set was Ultra 40s.
I’m using PAC 1225’s with titanium retainers.


SPECIFICATIONS
  • Part# PAC-1225
  • NamePAC-1225 Drag Race Dual
  • SKUPAC-1225
  • Alt Part#PAC-1225-16
  • DescriptionDrag Race 1200 Series Valve Spring 1.550 - 0.800 lift
  • Outside Diameter1.550
  • Outer Spring ID1.100
  • Middle Spring IDN/A
  • Damperno
  • Inner Spring ID0.788
  • Install Height2.000
  • Load at Installed Height250
  • Spring Open Height1.200
  • Spring Open Load765
  • Recommended Valve Lift0.800
  • Spring Rate (lbs/in)644
  • Coil Bind (max)1.150
 
How's valve spring pressure? Know it's all fresh. My Mustang has a set of Moroso Blue Max wires that were on my Camaro from back in the 90s. I took them off chasing a drop in performance and when they didn't fix it I saved them for projects in the works. New set was Ultra 40s.
If you are questioning the valve springs due to it breaking up at high rpm, I figured out what it was last night. The tired Mallory box rev limiter was set for 7500, but causing issues at 6600-6700. I turned the rev limiter up to 8000 and it was clean on the last two passes.
 
I been watching the video.
I see quick lift in front almost looks like it unsettles rear tires a few revolutions before they hook 100%. It almost had separation and saw a little for a split second. Very little. My car bounced w 90/10s and unsettled rear constantly before my upgrade.
oir cars are way different but I like to slow down the front rise and get good separation in rear. Are those radials on rear? They look huge on that car. I forget what you posted about them but making them fit.
Im at 12/7 on rear Vikings. 80/20 front Afco shocks. Started rear at 10/5. But im just bracket/index racing.
 
I been watching the video.
I see quick lift in front almost looks like it unsettles rear tires a few revolutions before they hook 100%. It almost had separation and saw a little for a split second. Very little. My car bounced w 90/10s and unsettled rear constantly before my upgrade.
oir cars are way different but I like to slow down the front rise and get good separation in rear. Are those radials on rear? They look huge on that car. I forget what you posted about them but making them fit.
Im at 12/7 on rear Vikings. 80/20 front Afco shocks. Started rear at 10/5. But im just bracket/index racing.
Yes, I mentioned to a friend that was with me that I need to go one click on the front next time to see if it helps. The tires are slicks 29x12.5-15
 
If you are questioning the valve springs due to it breaking up at high rpm, I figured out what it was last night. The tired Mallory box rev limiter was set for 7500, but causing issues at 6600-6700. I turned the rev limiter up to 8000 and it was clean on the last two passes.

Are you going to stay with the Mallory or install the MSD 7?
 
Back
Top