Breaking up at high rpm, carb issues, and converter issues.

if you want to test wires
get a silicone oven mitt (becomes obvious soon)
Start car
wiggle and tug wires while idling
if you have a shit connection, the car will stumble
or be a man and do it barehanded
i shut an engine off on the dyno that had a leaking coil wire i wasnt hip to too two ™
pushed on the motorplate to move the engine over a touch, and apparently used the coil for leverage
the coil wire leaked and went through ol bob
as im sitting on the floor with a non running engine i realized the error of my ways
Shit I always moved the wires around barehanded. I did get a really good hit from one of those old bigass yellow Accel coils.
 
Off topic, but......

As a youngster I played ball. Came very close to making the big show. A childhood team mate did make it. Detroit Tigers picked him up as a pitcher. 4th inning of their first preseason game they call him out of the bullpen. Coach hands him the ball and tells him this is where we find out if you can follow orders and tells him to hit the batter in the head with his first pitch. My buddy is shitting his pants. He does not want to kill the guy, so he drills the batter square in the hip with a fastball. Coach comes back out and sends him to the locker to pack his shit. Montreal picks him up. First time he is called to the mound the coach tells him to hit the batter in the head with a pitch. I asked my buddy, "what did you do". He said......I split the guys fucking helmet in half!:LOL:
if i was him, id have done the same thing...lol

i was to stupid and poor to realize
I was very very good at 1st base
i talked to scouts at an allstar tournament when i was 14 and 15
I couldnt afford to do anything if i didnt have a job, as my parents were very poor
so i quit baseball to work
I should have tried to walk on in college, but again, i had to work and montana state doesnt have a baseball program
 
Shit I always moved the wires around barehanded. I did get a really good hit from one of those old bigass yellow Accel coils.
a grid with the big msd coil is no joke
i got hit with 475v ac from a guitar amp one time too
that gets your attention
 
a grid with the big msd coil is no joke
i got hit with 475v ac from a guitar amp one time too
that gets your attention
Somewhat recently I got 900V AC from an amp with 845 tubes. In one arm and out the other. Very electrifying but a good way to off yourself!

None of that girly man 450V plate voltage stuff, these amps run right around 1000V plate voltage.
 
Somewhat recently I got 900V AC from an amp with 845 tubes. In one arm and out the other. Very electrifying but a good way to off yourself!
when i first got into fucking with amps
i learned the old rule about if its live, only use one hand while working on it
keeps it from passing through the chest cavity
probably what saved me
it went in my thumb and came out the fingers on that hand
top 3 worst pains ever
cost me about 200 in tubes because me and the amp crashed down...lol
 
when i first got into fucking with amps
i learned the old rule about if its live, only use one hand while working on it
keeps it from passing through the chest cavity
probably what saved me
it went in my thumb and came out the fingers on that hand
top 3 worst pains ever
cost me about 200 in tubes because me and the amp crashed down...lol
Yeah I fucked up on that deal. I have gotten plenty of 400-500VDC shocks over the years, also the 25KV high voltage in TVs but that's pretty low current. One thing that will make you dead fast is the 3KV in a microwave as it's high current.
 
when i was 11 ish, i threw a baseball from way out and a kid wasnt paying attention even though they knew i was throwing it.
hit him in the side of the head with a really sickening sound.
kid grew up to be kinda fucked up ,and ive always wondered if it was my fault....

not to be confused with the kid i threw at his head when i was pitching...lol
We were tossing a baseball around in my best friends front yard, probably about the same time you were.
Well, I was a pitcher, and for my age threw pretty hard.
I am in the middle of a windup throwing to my best friends older brother, I would say he was 6 or 7 years older than me.
Well, for some reason he turned his head and looked away from me and I couldn't stop the throw in time.
Yeah, drilled him HARD!
Knocked the wind out of him, was grounded for a week, from my best friends MOM!
She said you don't come back here till next week now.
We still laugh about that today, total accident.
 
Looks like you have the standard small Pro billet cap. Probably not the issue, but pull that rotor and look underneath it if you continue to have problems. I have the low profile Ford based crank trigger distributor and it burned through the bottom of the rotor and was grounding out, went from a slight miss to not even running. It actually loosened up last time I was at the track and fucked me again, that's on me, but the only problems I've had in 7 years were that damn rotor. It gets loctited from now on. I'd switch to the larger Cap Adapt cap and rotor too in the future, way better in my opinion.
 
Looks like you have the standard small Pro billet cap. Probably not the issue, but pull that rotor and look underneath it if you continue to have problems. I have the low profile Ford based crank trigger distributor and it burned through the bottom of the rotor and was grounding out, went from a slight miss to not even running. It actually loosened up last time I was at the track and fucked me again, that's on me, but the only problems I've had in 7 years were that damn rotor. It gets loctited from now on. I'd switch to the larger Cap Adapt cap and rotor too in the future, way better in my opinion.
I looked at the rotor last night and it looked good. I have a fixed rotor at the moment. I have another distributor from a 302 with the larger cap, but I don't know if the base of it will work? Let me go look at it. But yes, I would rather have the larger cap.

Edit: nope the base is too big. I guess I have to buy that kit.
 
Look inside the cap at the carbon button contact to the rotor blade. MSD billet distributors are a mimic of the Delco points distributor but with the shaft end play shimmed tight. Nevermind the gear angle and the load of driving the oil pump pushes the gear up against the housing when the engine is running.

The added shim thickness at the lower end of the housing pulls the shaft and rotor down from the cap so the rotor blade does not contact the carbon button .... the arc jumping from carbon button to the rotor spring contact eats the carbon button and the carbon powder spreads out all around the plug wire terminals inside the cap .... pop bang pow pfftglrbl

This same thing happened 60 years ago when people noticed the Delco Chevy distributors have ~.060" end play and shimmed them tight, which when the aluminum housings heat to engine operating temperature expand more than the steel shaft so all the end play is tight and the advance mechanism locks up, sticks retarded or ?

The fix is to bend the spring contact up a little bit so it touches the button.

Nevermind all that, I forgot the OP's whip is a Ferd, which have their own nest of snakes with the gear location flustercuck when the gear is changed. Whoever eliminated literacy from public school curriculum should be among the hung.
 
Look inside the cap at the carbon button contact to the rotor blade. MSD billet distributors are a mimic of the Delco points distributor but with the shaft end play shimmed tight. Nevermind the gear angle and the load of driving the oil pump pushes the gear up against the housing when the engine is running.

The added shim thickness at the lower end of the housing pulls the shaft and rotor down from the cap so the rotor blade does not contact the carbon button .... the arc jumping from carbon button to the rotor spring contact eats the carbon button and the carbon powder spreads out all around the plug wire terminals inside the cap .... pop bang pow pfftglrbl

This same thing happened 60 years ago when people noticed the Delco Chevy distributors have ~.060" end play and shimmed them tight, which when the aluminum housings heat to engine operating temperature expand more than the steel shaft so all the end play is tight and the advance mechanism locks up, sticks retarded or ?

The fix is to bend the spring contact up a little bit so it touches the button.

Nevermind all that, I forgot the OP's whip is a Ferd, which have their own nest of snakes with the gear location flustercuck when the gear is changed. Whoever eliminated literacy from public school curriculum should be among the hung.
The rotor blade has slight witness marks, and the button looks brand new, which it is. No signs of arcing or anything burnt.
 
if i was him, id have done the same thing...lol

i was to stupid and poor to realize
I was very very good at 1st base
i talked to scouts at an allstar tournament when i was 14 and 15
I couldnt afford to do anything if i didnt have a job, as my parents were very poor
so i quit baseball to work
I should have tried to walk on in college, but again, i had to work and montana state doesnt have a baseball program
You don't want to hear about how bad I fucked up the golden opportunity for Oklahoma State.....🤦
 
That was the craziest thing I ever had to deal with. Don't even want to add up all the new parts that were thrown at that mess for nothing. Ended up being the ONLY electrical component that nobody mentioned, so was not replaced until you found it at Cecil. A $28 part fixed it. I still have a spare in my trailer.

BTW, I blame that failure on goneracin.......he put too much torque in my motor.:lmao:
refresh my memory. I remember the problem you were having ( and Baum adding his .02) and remember you talking about finding the problem . I just do not remember what the problem was
 
refresh my memory. I remember the problem you were having ( and Baum adding his .02) and remember you talking about finding the problem . I just do not remember what the problem was

After changing the master kill switch, which was legitimately harder than swapping engines in that car, changing the coil, the ignition box, distributor, and eliminating the transbrake and delay box, it turned out to be a 28 dollar Ford solenoid mounted on the firewall. One of the main power posts broke inside the plastic housing. It would make contact sitting still or doing a burnout, but when I would launch the car it would pull apart killing the power to the car. It would then close back up, then pull apart, etc. until we got far enough down track that we would be below 2G's acceleration, then it would stay contacted and pull like normal the rest of the run.

I am still remembering stuff.......changed the fuel pump and rebuilt the carbs twice as well.
 
After changing the master kill switch, which was legitimately harder than swapping engines in that car, changing the coil, the ignition box, distributor, and eliminating the transbrake and delay box, it turned out to be a 28 dollar Ford solenoid mounted on the firewall. One of the main power posts broke inside the plastic housing. It would make contact sitting still or doing a burnout, but when I would launch the car it would pull apart killing the power to the car. It would then close back up, then pull apart, etc. until we got far enough down track that we would be below 2G's acceleration, then it would stay contacted and pull like normal the rest of the run.

I am still remembering stuff.......changed the fuel pump and rebuilt the carbs twice as well.
i remember now
 
This is probably the best video to see what it was doing. I aborted multiple runs prior to this one, but I was so pissed off at this point I just keep the gas pedal on the floor to see what would happen.

 
Ready for testing tomorrow, if the weather holds up.

the new wideband is solid as a rock. I think the readings from the other one might have been fubar.

If the sensor is still in the same location the difference is this gauge has more smoothing so the display doesn't change so fast to make it easier to read.

Several years ago a pal had a problem like this with his 540 BBC that acted like it just quit pulling at 6000 RPM, just sort of spavin up and mumble. In several weeks he changed every possible fuel and electrical component and the torque converter to finally find out it was the red top Optima battery. Lucky for him he owned the dyno because we teased him he just got a dyno to have a place to park his his hot rod.
 
If the sensor is still in the same location the difference is this gauge has more smoothing so the display doesn't change so fast to make it easier to read.

Several years ago a pal had a problem like this with his 540 BBC that acted like it just quit pulling at 6000 RPM, just sort of spavin up and mumble. In several weeks he changed every possible fuel and electrical component and the torque converter to finally find out it was the red top Optima battery. Lucky for him he owned the dyno because we teased him he just got a dyno to have a place to park his his hot rod.
ive seen multiple optimas fail
and a battery can def cause a miss
at one point if a pro stock car shook, we would change the battery as it would piss the plates off in it and you would all of a sudden have an intermittent miss
Ive seen a tach cause stupidity too
ive actually seen a chassis that was magnetic enough to cause issues. Degaussed the chassis and the issue went away
 
If the sensor is still in the same location the difference is this gauge has more smoothing so the display doesn't change so fast to make it easier to read.

Several years ago a pal had a problem like this with his 540 BBC that acted like it just quit pulling at 6000 RPM, just sort of spavin up and mumble. In several weeks he changed every possible fuel and electrical component and the torque converter to finally find out it was the red top Optima battery. Lucky for him he owned the dyno because we teased him he just got a dyno to have a place to park his his hot rod.
Well, I do have a red top optima battery. Oddly enough, a friend was just telling me how shitty it was and that I should get an XS.
 
Back
Top