Breaking up at high rpm, carb issues, and converter issues.

Is an air filter on this carb? How close are the bowl vents to any surface above them, filter lid or hood scoop or ??
 
He detailed everything pretty good in his build thread.

 
Well….

I’ve never tuned off of any gauges, just what the car does so bear with me here.

I tell folks 1 jets size at a time cuz I know they’ll go 2-3 at the most & usually the carb is somewhere close. Your carb (unless accidentally misboxxed) should have been close on delivery, probably a little fat for safety. Taking out 12 is so fuckn much it’s ridiculous. If that thing ran 115+ after taking out 12 & didn’t melt a piston, then it’s definitely not lean.

That little flutter at rpm COULD BE a lean condition but I don’t think so. Maybe a bad plug or you mighta cracked it on install.

My limited real world sperience says a good bracket carb is sized & balanced perfectly down the middle of the tune, maybe a tick on the fat side, so small weather changes don’t drive it OUT of tune & it’s very predictable along the way.

Idle, transition & wfo are all we’re worried about on a drag car.

Not going up clean on the chip is something I adjust on a dam fine tune by turning the mixture screws out maybe 1/4 turn if the weather gets REAL good. That’s how finicky/easy it should be to fix that issue but it has to be a well balanced carb.
When that secondary idle screw moved it changed everything from idle to transition all the way up to WFO so any chance at a decent tune was gone. I could see it being far enough off to dribble out of the back boosters which messes everything up

Converters are pretty cool things. They will stall higher or lower based solely on what the crank tells them. More steam, more stall & vice versa (to a point, especially if they are tight)

I think you have maybe several little issues messing with you & getting them worked out can & probably will be tedious. I don’t think you have just 1 issue. You hafta fix the little issues & get a repeatable baseline & then start tuning it up. Once you get it tuned right then you’ll know what the converter actually does. I could be & have been wrong before. Lol

I have an MSD 7AL2 fresh from MSD with paperwork that I’ll ship you if you want to try that but please get rid of that old box.

I also have my severely worked over 750 that will rip your head off from idle & probably run 5.80’s on yours if you want to try it.

You are welcome to both.


btw I saw your car launch differently on every pass but that’s down the road a ways. lol
Before getting rid of this box, I’m going to try a few things to see if I can clear up this miss. No spark plugs are cracked, I’m very meticulous with that process and I actually use a tq wrench when I tighten them.

I get you with the converter, other stuff has to get worked out to truly see what it’s doing.

Every launch was different, but every launch was the same lol

What has me a bit miffed is the car ran 6.08 last week and 6.08 this week with 12 jet sizes smaller. How the F does that happen?

Thank you VERY much on the offer for both the ignition and the carb, but I never borrow things like that. I’m confident that I’ll get this sorted out.

I should have bought the MSD grid system in the off season. That was my plan and then I held off.
 
What has me a bit miffed is the car ran 6.08 last week and 6.08 this week with 12 jet sizes smaller. How the F does that happen?


This part right here has me genuinely lost.

No way that actually happened is my 1rd thought but I’m still trying to think that through. That car sounded pretty dam good at idle & & 115+ is making pretty good steam. Something doesn’t add up on the 12 sizes.

12 sizes on EACH jet or 3x4=12?
 
This part right here has me genuinely lost.

No way that actually happened is my 1rd thought but I’m still trying to think that through. That car sounded pretty dam good at idle & & 115+ is making pretty good steam. Something doesn’t add up on the 12 sizes.

12 sizes on EACH jet or 3x4=12?
Maybe my math was a little off, but I received this carb from BLP with .106 primary jets and .118 secondaries.

Last night I started with .086”/.108
The last 2 passes I switched to .084”/..106”
 
This part right here has me genuinely lost.

No way that actually happened is my 1rd thought but I’m still trying to think that through. That car sounded pretty dam good at idle & & 115+ is making pretty good steam. Something doesn’t add up on the 12 sizes.

12 sizes on EACH jet or 3x4=12?

 
Do me & everyone else a huge favor. Stop relying on your wide band, until you pull plugs every pass at the end of the track like I do every time, to see if my wideband tells me what the plugs show me.
 
Ooh, if your carb guy says to send it back, then send it back to them. That is not a normal carb & cant be compared to a normal carb. My carb is not normal & cant be compared to normal carb setups either. If you chose to buy an out of the box Holley from one of the retailers, you may have what is close to the regular Holley style tuneups that cover emulsion, air bleeds, jets, etc... My carb guy & yours, & a few others that have a clue on how to skin a cat differently or think out side of the box, don’t follow the original path.
 
Ooh, if your carb guy says to send it back, then send it back to them. That is not a normal carb & cant be compared to a normal carb. My carb is not normal & cant be compared to normal carb setups either. If you chose to buy an out of the box Holley from one of the retailers, you may have what is close to the regular Holley style tuneups that cover emulsion, air bleeds, jets, etc... My carb guy & yours, & a few others that have a clue on how to skin a cat differently or think out side of the box, don’t follow the original path.

Pardon me if I think that last sentence is hilariously funny.

Everybody works off of the original calibration in 67? factory high performance metering blocks, before any emissions crap started sneaking in. Even the IFR in the bottom of the block was original to that setup.

All kinds of different emulsion packages & tricks to go with them have been tried & mostly abandoned & left everybody using that early calibration with adjustments made to fit the combo.

Back to basics for the 1,347,976rd time. lol
 
Maybe my math was a little off, but I received this carb from BLP with .106 primary jets and .118 secondaries.

Last night I started with .086”/.108
The last 2 passes I switched to .084”/..106”


According to the sheet the jets are numbered in 1000ths of an inch difference.

106 - 86= 20… - 84 is 22. That’s 20ish % in area. That’s a Royal Fuck Ton.

The main wells should be around .160 so flowing enough @ 106 wasn’t the problem.

I don’t get it.
 
.012 is not 12 jets, its 12 thou so roughly 3-4 jets
.025 is fine. i ran 1500 hp na to 11,500 at .025...lol
throw that box away
the signal wires should NEVER be near noisy shit, like an alternator wire
fuck, take the alt belt off if you can for a pass?
i use moroso, msd or lately Scott customs, which imo are the best wire on the planet
Do me & everyone else a huge favor. Stop relying on your wide band, until you pull plugs every pass at the end of the track like I do every time, to see if my wideband tells me what the plugs show me.
ive tuned at a very high level using o2's
i use my otoscope a lot, but ive sent shit that went in the 3's in the 1/8th using o2 data
but maybe im wrong...lol
 
.012 is not 12 jets, its 12 thou so roughly 3-4 jets
.025 is fine. i ran 1500 hp na to 11,500 at .025...lol
throw that box away
the signal wires should NEVER be near noisy shit, like an alternator wire
fuck, take the alt belt off if you can for a pass?
i use moroso, msd or lately Scott customs, which imo are the best wire on the planet

ive tuned at a very high level using o2's
i use my otoscope a lot, but ive sent shit that went in the 3's in the 1/8th using o2 data
but maybe im wrong...lol


He took out roughly 20% of jet area on the primary side & 12% on the secondary side. That’s roughly 16% in 1 shot.

How could that big of a swing NOT affect it HARDLY AT ALL is what I can’t wrap my empty little brain around.
 
Maybe my math was a little off, but I received this carb from BLP with .106 primary jets and .118 secondaries.

Last night I started with .086”/.108
The last 2 passes I switched to .084”/..106”

Came into this thread reading the 2nd page, but the above quoted post jumped out at me.....

You got the carb from BLP, so it stands to reason there were BLP jets in it. When you dropped jet sizes, did you use BLP jet, or Holley jets?
 
He took out roughly 20% of jet area on the primary side & 12% on the secondary side. That’s roughly 16% in 1 shot.

How could that big of a swing NOT affect it HARDLY AT ALL is what I can’t wrap my empty little brain around.
i get that
i think something else is fucking up his chee...lol
for me its normal to take .020+ out of a carb, no one understands i got no air in the air up here
i would throw the power valve in the trash and square jet it also, at least until you get WOT down
 
Came into this thread reading the 2nd page, but the above quoted post jumped out at me.....

You got the carb from BLP, so it stands to reason there were BLP jets in it. When you dropped jet sizes, did you use BLP jet, or Holley jets?
he used hole size, probably BLP
Rereading his posts i figured that out
 
Came into this thread reading the 2nd page, but the above quoted post jumped out at me.....

You got the carb from BLP, so it stands to reason there were BLP jets in it. When you dropped jet sizes, did you use BLP jet, or Holley jets?
Yes sir, BLP jets.
 
I would be running NGK -8 plugs. The -7's might be ok, but why chance it.
What fuel are you running?
If I try to run my engine at 12.0 A/F it is a total DOG!
I run either Sunoco Blue or Red, or VP C12 or better. My engine doesn't care, but when the A/F drops below 13.0 it cares a LOT about that!
It runs best 13.3 to 13.5 A/F on Blue, 13.5 to 13.8 A/F on Red.
The higher the octane the leaner we run these things............
Bob can confirm this, or I am a total idiot........ :)

I had a customer that had a 11:1 engine with 15psi of boost on it, we ran an MSD 6AL and a Blaster 3 coil.
Never missed a beat, went mid 9's, SRGN knows the car, he has seen it many, many times.

Keep the crank trigger wires away from all other wires.........

I would not think about the convertor until the engine runs correctly.

Do you have a chassis dyno local? I love those things.

As far as plug wires go, pretty sure you have to use those 135* boots on your setup, like a BBC uses too.
Well, I can't tell you how many pre-made wires I found BAD out of the box due to the crimp and the way those boots work.
Make your own.
I like MSD Red wires, never an issue WHEN I MAKE MY OWN!
Serious, you wouldn't believe the hell I have been through with people and those damn 135* wires!
Straight and 90*, NEVER a problem.
We took a set of wires off a friends 199x Ford F150 at the track one night since they had the proper boots to fit the BBC we were running and the engine finally got to 7500. Before that it hit a "rev limiter" at 5500 every damn pass! We had two brand new plugs wires that were intermittent. When I sliced the boots open I showed the guys what was wrong. Two sets, brand new, never abused, fuck that, I make my own stuff!

Can't help with the carb, been running EFI since 1988...........
Plenty of people can help you with that and if you have changed jet sizes that much something else is up.
 
And, keep the faith!
You'll get there.
I went through some struggles with my car when I did a brand new combo.
New engine, trans, and rear.......
Took two weeks but got it right.

Chassis dynos are so much better to figure shit out on than the track.
 
Back
Top