Before getting rid of this box, I’m going to try a few things to see if I can clear up this miss. No spark plugs are cracked, I’m very meticulous with that process and I actually use a tq wrench when I tighten them.Well….
I’ve never tuned off of any gauges, just what the car does so bear with me here.
I tell folks 1 jets size at a time cuz I know they’ll go 2-3 at the most & usually the carb is somewhere close. Your carb (unless accidentally misboxxed) should have been close on delivery, probably a little fat for safety. Taking out 12 is so fuckn much it’s ridiculous. If that thing ran 115+ after taking out 12 & didn’t melt a piston, then it’s definitely not lean.
That little flutter at rpm COULD BE a lean condition but I don’t think so. Maybe a bad plug or you mighta cracked it on install.
My limited real world sperience says a good bracket carb is sized & balanced perfectly down the middle of the tune, maybe a tick on the fat side, so small weather changes don’t drive it OUT of tune & it’s very predictable along the way.
Idle, transition & wfo are all we’re worried about on a drag car.
Not going up clean on the chip is something I adjust on a dam fine tune by turning the mixture screws out maybe 1/4 turn if the weather gets REAL good. That’s how finicky/easy it should be to fix that issue but it has to be a well balanced carb.
When that secondary idle screw moved it changed everything from idle to transition all the way up to WFO so any chance at a decent tune was gone. I could see it being far enough off to dribble out of the back boosters which messes everything up
Converters are pretty cool things. They will stall higher or lower based solely on what the crank tells them. More steam, more stall & vice versa (to a point, especially if they are tight)
I think you have maybe several little issues messing with you & getting them worked out can & probably will be tedious. I don’t think you have just 1 issue. You hafta fix the little issues & get a repeatable baseline & then start tuning it up. Once you get it tuned right then you’ll know what the converter actually does. I could be & have been wrong before. Lol
I have an MSD 7AL2 fresh from MSD with paperwork that I’ll ship you if you want to try that but please get rid of that old box.
I also have my severely worked over 750 that will rip your head off from idle & probably run 5.80’s on yours if you want to try it.
You are welcome to both.
btw I saw your car launch differently on every pass but that’s down the road a ways. lol
We went from .032” to .025” last night with no change.Try less gap on the next plug set
What has me a bit miffed is the car ran 6.08 last week and 6.08 this week with 12 jet sizes smaller. How the F does that happen?
Maybe my math was a little off, but I received this carb from BLP with .106 primary jets and .118 secondaries.This part right here has me genuinely lost.
No way that actually happened is my 1rd thought but I’m still trying to think that through. That car sounded pretty dam good at idle & & 115+ is making pretty good steam. Something doesn’t add up on the 12 sizes.
12 sizes on EACH jet or 3x4=12?
Ooh, if your carb guy says to send it back, then send it back to them. That is not a normal carb & cant be compared to a normal carb. My carb is not normal & cant be compared to normal carb setups either. If you chose to buy an out of the box Holley from one of the retailers, you may have what is close to the regular Holley style tuneups that cover emulsion, air bleeds, jets, etc... My carb guy & yours, & a few others that have a clue on how to skin a cat differently or think out side of the box, don’t follow the original path.
Maybe my math was a little off, but I received this carb from BLP with .106 primary jets and .118 secondaries.
Last night I started with .086”/.108
The last 2 passes I switched to .084”/..106”
ive tuned at a very high level using o2'sDo me & everyone else a huge favor. Stop relying on your wide band, until you pull plugs every pass at the end of the track like I do every time, to see if my wideband tells me what the plugs show me.
.012 is not 12 jets, its 12 thou so roughly 3-4 jets
.025 is fine. i ran 1500 hp na to 11,500 at .025...lol
throw that box away
the signal wires should NEVER be near noisy shit, like an alternator wire
fuck, take the alt belt off if you can for a pass?
i use moroso, msd or lately Scott customs, which imo are the best wire on the planet
ive tuned at a very high level using o2's
i use my otoscope a lot, but ive sent shit that went in the 3's in the 1/8th using o2 data
but maybe im wrong...lol
Maybe my math was a little off, but I received this carb from BLP with .106 primary jets and .118 secondaries.
Last night I started with .086”/.108
The last 2 passes I switched to .084”/..106”
i get thatHe took out roughly 20% of jet area on the primary side & 12% on the secondary side. That’s roughly 16% in 1 shot.
How could that big of a swing NOT affect it HARDLY AT ALL is what I can’t wrap my empty little brain around.
he used hole size, probably BLPCame into this thread reading the 2nd page, but the above quoted post jumped out at me.....
You got the carb from BLP, so it stands to reason there were BLP jets in it. When you dropped jet sizes, did you use BLP jet, or Holley jets?
Yes sir, BLP jets.Came into this thread reading the 2nd page, but the above quoted post jumped out at me.....
You got the carb from BLP, so it stands to reason there were BLP jets in it. When you dropped jet sizes, did you use BLP jet, or Holley jets?