Breaking up at high rpm, carb issues, and converter issues.

Patriot Racer

Freeeeeeedom!
Joined
Sep 18, 2021
Messages
9,229
Reaction score
24,327
Points
153
Location
Northern Illinois
Went to the track last night and ran into a bunch of issues.

First off, I have gone down 12 jet sizes on this BLP carb and it’s still rich. 11.9-12.0 at WOT going down the track. Next after each pass (3 total), I couldn’t figure out why throttle would stick at 2500-3000 rpm after a run.

Scary shit coming down the return road watching temp creep up and scaring the shit out of the time slip guy. I finally figured it out. There is an Allen screw that goes in the carb from the bottom that the idle screw pushes against. While at WOT it kept vibrating upward and wouldn’t allow the secondaries to close. WTF BLP, a dab of loctite should have been put on that during assembly!

Next, while at WOT down track engine would start breaking up around 6700-6800 from what I could tell. It might even be breaking g up when I come off the transbrake. My rev limiter is set to 7500. I am using an old outdated Mallory 685 ignition and coil. Brand new MSD distributor, fire core wires and NGK 7 plugs.

The converter flashed last week to 5500 when I launched at 4200. Last night all launches were at 5000 and the converter didn’t do shit. It was supposed to have a 6300 stall. However, if I shift at 7000, it falls back to 6000, so that isn’t making sense.

I was in contact with SRGN last night. We tried to see how it would respond by closing spark plug gap from .032” to .025, but no change. I’m kind of lost as what to do next. BLP already told me to send the carb back.

I was contemplating upgrading the ignition this past winter and even made a thread about it. I held off. I’m going to get the power grid system at some point, but I don’t want to drop that cash right now and still end up with the same issue.

Looking for advice/suggestions on my next step.
 
I’ll try to load up the videos in a bit, but you can hear the engine bog when coming of the 2 step.
 
Take a look at ripple voltage. Measure the AC voltage getting put out by the alternator at 3k RPM. If you have ripple voltage in the system, it can wreak havoc with ignition systems.
 
Run 3, in car, you can hear the converter being down the motor on launch and you can clearly hear the break up down track in 2nd gear around 6700 and up.

 
Went to the track last night and ran into a bunch of issues.

First off, I have gone down 12 jet sizes on this BLP carb and it’s still rich. 11.9-12.0 at WOT going down the track. Next after each pass (3 total), I couldn’t figure out why throttle would stick at 2500-3000 rpm after a run.

Scary shit coming down the return road watching temp creep up and scaring the shit out of the time slip guy. I finally figured it out. There is an Allen screw that goes in the carb from the bottom that the idle screw pushes against. While at WOT it kept vibrating upward and wouldn’t allow the secondaries to close. WTF BLP, a dab of loctite should have been put on that during assembly!

Next, while at WOT down track engine would start breaking up around 6700-6800 from what I could tell. It might even be breaking g up when I come off the transbrake. My rev limiter is set to 7500. I am using an old outdated Mallory 685 ignition and coil. Brand new MSD distributor, fire core wires and NGK 7 plugs.

The converter flashed last week to 5500 when I launched at 4200. Last night all launches were at 5000 and the converter didn’t do shit. It was supposed to have a 6300 stall. However, if I shift at 7000, it falls back to 6000, so that isn’t making sense.

I was in contact with SRGN last night. We tried to see how it would respond by closing spark plug gap from .032” to .025, but no change. I’m kind of lost as what to do next. BLP already told me to send the carb back.

I was contemplating upgrading the ignition this past winter and even made a thread about it. I held off. I’m going to get the power grid system at some point, but I don’t want to drop that cash right now and still end up with the same issue.

Looking for advice/suggestions on my next step.
fallback will always be higher than the flash off the 2 step
engine is making more power at the bottom of the gear than it is off the 2 step
and gear ratio in low vs high tightens the converter up some
what are you usingfor a trigger? the msd distributor or a crank trigger?
Which MSD dist? ive had issues with the internal trigger on an msd.
Do you have advance locked out or are you using mechanical advance?
I would throw the old mallory as far away from me as i could....lol.
12.0 isnt rich enough to cause a miss unless the ignition isnt up to the task
a 7 is pretty hot plug. How much compression?
Im not a fan of the firecore wires, but i doubt that is the issue
 
Are you certain the NGKs are legit?
Even when purchased through Amazon with Amazon as the seller, there is no guarantee they are legit as Amazon mixes bins.
 
Are you certain the NGKs are legit?
Even when purchased through Amazon with Amazon as the seller, there is no guarantee they are legit as Amazon mixes bins.
good point
ive seen a lot of fake bullshit on scamazon
I pay more, but i only buy from a legit distributor
i have seen a bad plug oout of the box cause some weird shit for sure. Autolite after they moved production went to shit so bad we had to stop using them
 
fallback will always be higher than the flash off the 2 step
engine is making more power at the bottom of the gear than it is off the 2 step
and gear ratio in low vs high tightens the converter up some Understood.
what are you usingfor a trigger? the msd distributor or a crank trigger? The MSD distributor
Which MSD dist? ive had issues with the internal trigger on an msd. Pro Billet 857831
Do you have advance locked out or are you using mechanical advance? Locked out, timing @ 34*
I would throw the old mallory as far away from me as i could....lol. Noted!
12.0 isnt rich enough to cause a miss unless the ignition isnt up to the task
a 7 is pretty hot plug. Timing mark is right in the middle of the strap. How much compression? 13:1 ish
Im not a fan of the firecore wires, but i doubt that is the issue Everybody and I bought them. I have yet to feel a positive snap when inserting the wire onto the plug, but I don’t that’s it either because I wiggle it around and know it’s making contact. Just don’t feel that snap I did with my Taylor’s I had previously.
 
Are you certain the NGKs are legit?
Even when purchased through Amazon with Amazon as the seller, there is no guarantee they are legit as Amazon mixes bins.
Bought from advance auto parts store and first set was from competitionplus.com
 
fallback will always be higher than the flash off the 2 step
engine is making more power at the bottom of the gear than it is off the 2 step
and gear ratio in low vs high tightens the converter up some Understood.
what are you usingfor a trigger? the msd distributor or a crank trigger? The MSD distributor
Which MSD dist? ive had issues with the internal trigger on an msd. Pro Billet 857831
Do you have advance locked out or are you using mechanical advance? Locked out, timing @ 34*
I would throw the old mallory as far away from me as i could....lol. Noted!
12.0 isnt rich enough to cause a miss unless the ignition isnt up to the task
a 7 is pretty hot plug. Timing mark is right in the middle of the strap. How much compression? 13:1 ish
Im not a fan of the firecore wires, but i doubt that is the issue Everybody and I bought them. I have yet to feel a positive snap when I erring wire to plug, but I don’t that’s it either because I wiggle it around and know it’s making contact. Just don’t feel that snap I did with my Taylor’s I had previously.
Taylors are junk, as far as quality of conductor goes.
that was my experience with the firecore. A customer got them for free for an outlaw 632 deal. I didnt like them at all, but they didnt missfire
Check rotor phasing to make sure its phased.
I have seen the screws that hold the rotor together loosen as well, especially the 2 piece rotor with the base and top. The screw that holds the base on is a pain in the ass. not sure which rotor that uses
 
Taylors are junk, as far as quality of conductor goes.
that was my experience with the firecore. A customer got them for free for an outlaw 632 deal. I didnt like them at all, but they didnt missfire
Check rotor phasing to make sure its phased.
I have seen the screws that hold the rotor together loosen as well, especially the 2 piece rotor with the base and top. The screw that holds the base on is a pain in the ass. not sure which rotor that uses
But they snapped lol

What plug wires do you like? Moroso?
 
A good friend of mine that wires race cars suggested that I move my distributor pick up wires. They are currently routed through the firewall with the alternator wire and he thinks it might be getting interference.

I’m going to move them to see if that fixes it.
 
If you have a voltmeter, hook the positive lead up to the alternator, and the negative lead to ground. Set the meter to read AC voltage. Start the car, watch the meter when you raise the RPM to around 3000. If it reads more than .2 volts, you need a new rectifier bridge in the alternator.
 
High RPM ignition breaking up is a pain in the BUTT. Mine is currently doing it again. The signal wire and wires leading to the coil are wrapped in EMI/RFI shielding and grounded at each end, wires are also routed away from other electrical sources, new plugs, new Fire Core wires, MSD pro billet distributor locked out and phased, 3 different new alternators. Going to start throwing ignition parts away and replacing with new parts, starting with the coil.
I currently have this coil

 
I would try a known good carb on your car to rule out the fuel issue. I have seen a lot of high RPM mis-fire issues in my life and some of the fixes were surprising.
 
Went to the track last night and ran into a bunch of issues.

First off, I have gone down 12 jet sizes on this BLP carb and it’s still rich. 11.9-12.0 at WOT going down the track. Next after each pass (3 total), I couldn’t figure out why throttle would stick at 2500-3000 rpm after a run.

Scary shit coming down the return road watching temp creep up and scaring the shit out of the time slip guy. I finally figured it out. There is an Allen screw that goes in the carb from the bottom that the idle screw pushes against. While at WOT it kept vibrating upward and wouldn’t allow the secondaries to close. WTF BLP, a dab of loctite should have been put on that during assembly!

Next, while at WOT down track engine would start breaking up around 6700-6800 from what I could tell. It might even be breaking g up when I come off the transbrake. My rev limiter is set to 7500. I am using an old outdated Mallory 685 ignition and coil. Brand new MSD distributor, fire core wires and NGK 7 plugs.

The converter flashed last week to 5500 when I launched at 4200. Last night all launches were at 5000 and the converter didn’t do shit. It was supposed to have a 6300 stall. However, if I shift at 7000, it falls back to 6000, so that isn’t making sense.

I was in contact with SRGN last night. We tried to see how it would respond by closing spark plug gap from .032” to .025, but no change. I’m kind of lost as what to do next. BLP already told me to send the carb back.

I was contemplating upgrading the ignition this past winter and even made a thread about it. I held off. I’m going to get the power grid system at some point, but I don’t want to drop that cash right now and still end up with the same issue.

Looking for advice/suggestions on my next step.

Well….

I’ve never tuned off of any gauges, just what the car does so bear with me here.

I tell folks 1 jets size at a time cuz I know they’ll go 2-3 at the most & usually the carb is somewhere close. Your carb (unless accidentally misboxxed) should have been close on delivery, probably a little fat for safety. Taking out 12 is so fuckn much it’s ridiculous. If that thing ran 115+ after taking out 12 & didn’t melt a piston, then it’s definitely not lean.

That little flutter at rpm COULD BE a lean condition but I don’t think so. Maybe a bad plug or you mighta cracked it on install.

My limited real world sperience says a good bracket carb is sized & balanced perfectly down the middle of the tune, maybe a tick on the fat side, so small weather changes don’t drive it OUT of tune & it’s very predictable along the way.

Idle, transition & wfo are all we’re worried about on a drag car.

Not going up clean on the chip is something I adjust on a dam fine tune by turning the mixture screws out maybe 1/4 turn if the weather gets REAL good. That’s how finicky/easy it should be to fix that issue but it has to be a well balanced carb.
When that secondary idle screw moved it changed everything from idle to transition all the way up to WFO so any chance at a decent tune was gone. I could see it being far enough off to dribble out of the back boosters which messes everything up

Converters are pretty cool things. They will stall higher or lower based solely on what the crank tells them. More steam, more stall & vice versa (to a point, especially if they are tight)

I think you have maybe several little issues messing with you & getting them worked out can & probably will be tedious. I don’t think you have just 1 issue. You hafta fix the little issues & get a repeatable baseline & then start tuning it up. Once you get it tuned right then you’ll know what the converter actually does. I could be & have been wrong before. Lol

I have an MSD 7AL2 fresh from MSD with paperwork that I’ll ship you if you want to try that but please get rid of that old box.

I also have my severely worked over 750 that will rip your head off from idle & probably run 5.80’s on yours if you want to try it.

You are welcome to both.


btw I saw your car launch differently on every pass but that’s down the road a ways. lol
 
Back
Top