Big Bore 427w

I got a little more done on the car last night. Converter is now properly spaced and bolted down. I had to trim some of the snout off the crank mandrel to clear the radiator, and then mounted the radiator.

I got the upper hose made, but had to order some fittings for the lower one. The height of the 351w compared to the 302 is stretching my throttle cable, so I ordered a new one.

chipping away at it.

 
Can't wait to see how it runs. What does the car weigh? What do you expect it to make power-wise? RPM range? Convertor stall?

I ask all this because you have the Ford version of my SBC, but I bet better heads!
While my heads are decent, especially for 23* stuff, they are no comparison to the 18* and 15* stuff out there.
Hell, stock LS3 heads may flow close to what my very-worked heads flow. Then again, they are 15* heads from the factory, following Fords lead!

I built my combo to try to go 8.50 Index Racing with Nitrous and Bracket Race it (Footbrake) most of the time. Well, that didn't work. I was able to go 8.90's no problem and did a special Index Class we had locally for a few years, but no way to go 8.50 without a convertor and rear gear swap, I was already crossing the stripe at 8400rpm and only going 156mph.............. It would run 10.00 to 10.20 without the blue bottle.

Well, I put the correct cam/gear/convertor in the car, changed nothing else, and went 9.40 @ 146 or so. But no more room for nitrous at that point, without spinning it to 8400 or higher. I don't have deep pockets. I slow it down for 10.00 Index Racing now, well, for the last eight years I would say. Much more affordable this way.

My car is 3200 with me in it. Back in the nitrous days it was 3400.
 
Can't wait to see how it runs. What does the car weigh? What do you expect it to make power-wise? RPM range? Convertor stall?

I ask all this because you have the Ford version of my SBC, but I bet better heads!
While my heads are decent, especially for 23* stuff, they are no comparison to the 18* and 15* stuff out there.
Hell, stock LS3 heads may flow close to what my very-worked heads flow. Then again, they are 15* heads from the factory, following Fords lead!

I built my combo to try to go 8.50 Index Racing with Nitrous and Bracket Race it (Footbrake) most of the time. Well, that didn't work. I was able to go 8.90's no problem and did a special Index Class we had locally for a few years, but no way to go 8.50 without a convertor and rear gear swap, I was already crossing the stripe at 8400rpm and only going 156mph.............. It would run 10.00 to 10.20 without the blue bottle.

Well, I put the correct cam/gear/convertor in the car, changed nothing else, and went 9.40 @ 146 or so. But no more room for nitrous at that point, without spinning it to 8400 or higher. I don't have deep pockets. I slow it down for 10.00 Index Racing now, well, for the last eight years I would say. Much more affordable this way.

My car is 3200 with me in it. Back in the nitrous days it was 3400.
Power wise I'm thinking 650-700 from what other similar combos have run. plan is to shift around 7200, maybe 7500. Coan was shooting for converter stall of 6200-6300. With the 331 my car weighed 2623 lbs. with me in it. It will likely be heavier now due to the 351w block, larger intake, etc. However, I tried to compensate for the extra weight by going to a smaller radiator, optic armor windshield, etc., so it might be close to the same weight. As soon as it's all together I'll put it on the scales.
 
I shift at 7500, the convertor goes to 6600 when I don't run the restrictor plate. I wish I could get our cars that light. Third Gen F-Bodies are turds, they weigh a lot! Our slower car is about 100 pounds heavier, it is a T-Top car. Both have full cages, though hers is 1/2 and 1/2, mine is all mild steel. She has some chrome moly.
 
Little things getting done that aren’t worth taking pics of. However, I wasn’t sure I’d be able to get these headers to fit, but it’s in there. I had to raise the car, then raise the engine, then pry the engine but it’s in there.

 
Getting very close now. Hooked up transmission cable last night, torqued headers down, and installed the carb. Still need to install pushrods and rockers and set lash. All down hill after that.
I have different valve covers too. Those are just on to keep everything clean and to stop the new ones from getting banged up.


 
@Dennis112, I saw an old yellow bullet post and it seems as if you have, or had a very similar 427 combo. What does your car run and how much does it weigh? What transmission? Thanks.
 
@Dennis112, I saw an old yellow bullet post and it seems as if you have, or had a very similar 427 combo. What does your car run and how much does it weigh? What transmission? Thanks.

Best was 9.66@140.xx Racing weight was 3550lbs (Full interior/steel wheels.) Tranny was a GF101a 4 speed. It is a 11:1 434w running readily available no lead 93 octane convenance store pump gas.
 
Best was 9.66@140.xx Racing weight was 3550lbs (Full interior/steel wheels.) Tranny was a GF101a 4 speed. It is a 11:1 434w running readily available no lead 93 octane convenance store pump gas.
Damn, thanks for the reply. It will be interesting to see what I can muster.
 
Keep working at it might surprise you, like it did me:

View attachment 28804

Even old school setups can get it done with a big Windsor.


View attachment 28803
My car only weighed 2625 lbs. with me in it with the 331. I'm guessing it's going to come in around 2750 lbs. with this engine/trans. roughly 13.4:1 compression. If all goes well, I should be pleasantly surprised.
 
I got all of my rockers installed and cold lash set. I have to do some welding on my exhaust and then start adding fluids and running through all of my checks to make sure I didn’t forget anything. I should be attempting to fire this thing off in the next few days.
 
I got all of my rockers installed and cold lash set. I have to do some welding on my exhaust and then start adding fluids and running through all of my checks to make sure I didn’t forget anything. I should be attempting to fire this thing off in the next few days.

Think you will make some races this year?
 
Think you will make some races this year?
Yes. Once it’s running I’ll have to get a few more things squared away with suspension and possibly cutting quarter panel wheel opening for tire clearance, but it should definitely see the track this year.
 
Yes. Once it’s running I’ll have to get a few more things squared away with suspension and possibly cutting quarter panel wheel opening for tire clearance, but it should definitely see the track this year.

Awesome man, hope you can get out there soon.
 
Back
Top