Big Bore 427w

Well, after the first shop fiasco and losing $2900, I took my stuff to another shop, which was actually recommended to me by MAGNUM before I took it to the losing shop.

Anyway, it’s looking like the 2nd go will be the charm. Builder sent me a pic and progress.



Line hone is done, caps were not cut previously, but they are now. Everything is perfectly round within 1/10th now.
 
While waiting for my new engine to get sorted out, I decided to throw the Powerglide in the car. I got tired of tripping over it.

I like working by myself, I just concentrate better on what I’m doing. Who has been lying on the ground holdingsomething up while kicking the Jack handle up and down like a dog lifting it’s leg? Raise your ✋ 😆.

I have to trim those sheet metal screws that come with the hurst shifter. Long as hell.

 
Engine builder called today and said new pistons arrived yesterday and as long as no fly cutting of pistons is necessary shortblock will be ready Wednesday. 😱

I took the transmission back out, clearanced some things and put it back again. ooked up the transmission lines and mounted the lokar dipstick.



I also made some chromoly supports (@MAGNUM) for the front spoiler. I’m not sure if it was needed, but piece of mind to not have it flapping around.

 
Ok, I keep posting in the “what did you do to your car today?” Thread, but neglecting this build thread.

I’m slowly chipping away at all the little things that have to get done. Today I made a bracket for a new catch can, welded onto the front end tubing, painted it and then installed the new catch can.

 
The Jones Racing Products crank mandrel that I bought will not work with this beautiful internal balance romac balancer, so I bought an ATI.

if anyone with a SBF is interested in purchasing the romac please send me a PM.
 
Another small set back. I ordered all of these HTD pulleys after seeing Jones Racing Products at PRI last year. They never told me that I would have to run a specific balancer for the crank mandrel to work. I have a beautiful brand new romac on there and because the spacing for a sbf (fox) is built into it, it causes the mandrel to be too far forward. When I called Jones they said well did you tell us what balancer you were running? I said no because I didn't know, but if you would have told me which one I needed, I would have purchased it!

Anyway, they are researching which ATI balancer I need, which will likely be a BBC part and then they will send me a new mandrel for a 3 bolt balancer. Everything has to be a shit show.


Edit: They called me back and they are sending alternator spacers to line everything up. Now my concern is the mandrel hitting my radiator/fan. :rolleyes:
 

Attachments

  • balancer problem.jpg
    balancer problem.jpg
    175.6 KB · Views: 4
Last edited:
Stef's makes some nice stuff, I have one of their oil pans on my engine.
That LSM valve spring tool is tits isn't it! I have one too for my engine, I love it.
Now, that CSR pump, be very careful! I used to use them, but had nothing but problems, terrible design. I use Mezier now, been perfect for 10 years or so.
 
Stef's makes some nice stuff, I have one of their oil pans on my engine.
That LSM valve spring tool is tits isn't it! I have one too for my engine, I love it.
Now, that CSR pump, be very careful! I used to use them, but had nothing but problems, terrible design. I use Mezier now, been perfect for 10 years or so.
No issues with the water pump yet. What issues were you having and what is different about the design of the pump?

I always keep an eye on temps.
 
No issues with the water pump yet. What issues were you having and what is different about the design of the pump?

I always keep an eye on temps.
The seal!
The seal would leak allowing water into the motor and that was that, brushes and armature a complete mess and unuasable.
I always kept a spare motor for it.
Had to put one on at a race, it lasted 5 passes then it puked it's seal.
Bought a Mezier the next day, cried at the damn price, but it has been perfect.
Put on one our slow car too, sometimes you just have to bite the bullet, buy once cry once.
I sold all my CSR stuff to an engine builder so he could rebuild and use it all on his dyno.
He said so far so good, he has been lucky, but then again, they don't get a lot of use. Only fits a specific engine and most of us old school SBC guys are too cheap to put our engines on a dyno! :)
 
Ran into some issues yesterday, but I got it worked out. https://phantombullet.net/threads/tq-converter-mating-issues…help.26995/

Engine is in, but I had to order 1/4” shims to get the oil pan off the steering rack. My k-member doesn’t have dropped rack mounts, just offset rack bushings.



Pushrods arrived today, so now I can install rockers and adjust lash.



Plenty of work still to do.
 
Back
Top