The morning crew check in

explain this rigging to me
He is rigging down the top of that spar using a two cut method, or 'snap cut'. He made the first cut, then tied the rope in place. The groundman has the other end of the rope in a friction device to catch the piece. He will make a second cut from the back slightly higher than the existing cut and then push the piece off the spar.

To catch the rigging rope, he is using an adjustable rigging sling with two eyelets rather than a pulley. The rigging rope is tied to the piece with two hitches. A half hitch and then a running bowline. Two points of attachment are more secure and also keep the piece from flopping about as much after it is cut.
 
these are real popular around here....unless you're going to work. 30-35 MPH


we have set ups something like that here also .The ones the State and Turnpike uses have a "wing plow" that is on the side of the truck so it can clear 2 lanes, then raised up at a 90* when not in use. The one you posted is a "trailer" behind the truck when not in use . I have not seen any like the one pictured that has the plow& brine tank set up like that, not saying they don't have them out in the mountains , I just never saw that set up used around my area . People say that state workers dont earn their money, have them drive that MoFo down the road fast enough to blow the snow off the road . Most MoFos cant even drive their 5' wide 3000lb car down the road on a nice day.
 
Last edited:
we have set ups something like that here also .The ones the State and Turnpike uses have a "wing plow" that is on the side of the truck so it can clear 2 lanes, then raised up at a 90* when not in use. The one you posted is a "trailer" behind the truck when not in use . I have not seen any like the one pictured that has the plow& brine tank set up like that, not saying they don't have them out in the mountains , I just never saw that set up used around my area . People say that state works dont earn their money, have them drive that MoFo down the road fast enough to blow the snow snow off the road .Most MoFos cant even drive their 5' wide 3000lb car down the road on a nice day

lol....this is the 1st i've seen from the front.....followed them for hrs, it seems.
 
Most every Ash tree here in SW PA is dead . The Emerald Ash Borer killed them
Fly over a heavily wooded area and you will be amazed at how many ash trees are dead……. I cannot believe that a little bug did that much damage.

BTW! The ash borer is another "gift" from China along with the spotted lantern fly and the Wu Flu
 
Fly over a heavily wooded area and you will be amazed at how many ash trees are dead……. I cannot believe that a little bug did that much damage.

BTW! The ash borer is another "gift" from China along with the spotted lantern fly and the Wu Flu
I hear ya, no idea what the MLB is going to do for bats in the future.
I also heard on the news a few weeks ago the damage to trees the spotted lantern fly does to is not as harmful to the tree as first thought and wont cause the trees to die.
 
He is rigging down the top of that spar using a two cut method, or 'snap cut'. He made the first cut, then tied the rope in place. The groundman has the other end of the rope in a friction device to catch the piece. He will make a second cut from the back slightly higher than the existing cut and then push the piece off the spar.

To catch the rigging rope, he is using an adjustable rigging sling with two eyelets rather than a pulley. The rigging rope is tied to the piece with two hitches. A half hitch and then a running bowline. Two points of attachment are more secure and also keep the piece from flopping about as much after it is cut.
thats a lot to take in , but I think I understand a little bit
 
He is rigging down the top of that spar using a two cut method, or 'snap cut'. He made the first cut, then tied the rope in place. The groundman has the other end of the rope in a friction device to catch the piece. He will make a second cut from the back slightly higher than the existing cut and then push the piece off the spar.

To catch the rigging rope, he is using an adjustable rigging sling with two eyelets rather than a pulley. The rigging rope is tied to the piece with two hitches. A half hitch and then a running bowline. Two points of attachment are more secure and also keep the piece from flopping about as much after it is cut.
My people.....



*fistbump.


* I had to make clearance and to make sure rigging won't slip. If you notice my bites out of the stick to set rig.

When I first started tree work, we were false crotching and having the ropes smoke
 
Last edited:
thats a lot to take in , but I think I understand a little bit
Snap cut.

Instead of putting a box in the stick (Heavy wood) then back cut and letting it fall, I like a more controlled snap cut.

I set my 2-3 sets of rigging (pulleys or ring slings) pull rigging rope through, throw a qwik hitch in, and start the face cut. About half -3/4 through stop, then set the rigging rope- as pictured. To make certain the ground- rope guy knows I am ready, when i see the rig rope wiggling I will then make sure no crew- homeowner- ect is underneath or around where debris could possibly fly.

Give the rope guy my nod and make a back cut about halfway +/- through , just above the first cut. Now I can reposition the bucket back up, cause I have a controlled cut, I can take bigger pieces per rigging values.....

The cut stick stays- I look at the rope guy- nod, he nods back and I push pull on the stick and it snaps where I made the cuts, and I can lead the direction of the fall.
 
Last edited:
what happened?
Veins in the leg have valves that keep blood moving towards the heart... the valves can prolapse, and then blood and fluid begin to pool in your legs... not good.

So the doctor inserts a catheter into the veins causing the problem, and burns them shut...
Blood is rerouted to the main vein returning to the heart and flow from the leg is restored...
She says it will make my legs feel 20 years younger...

After each procedure, they tightly compression wrap the leg to help get the fluid out of the leg...

1 procedure down, 7 more to go...
Next one is tomorrow on the other leg. Then sonograms to verify that the veins are blocked..

Then onto the next two procedures next week.
 
Veins in the leg have valves that keep blood moving towards the heart... the valves can prolapse, and then blood and fluid begin to pool in your legs... not good.

So the doctor inserts a catheter into the veins causing the problem, and burns them shut...
Blood is rerouted to the main vein returning to the heart and flow from the leg is restored...
She says it will make my legs feel 20 years younger...

After each procedure, they tightly compression wrap the leg to help get the fluid out of the leg...

1 procedure down, 7 more to go...
Next one is tomorrow on the other leg. Then sonograms to verify that the veins are blocked..

Then onto the next two procedures next week.
Please go with lime green. And post
 
Lol.... an earlier cut on same tree stick




Shows after the snap cut section as seen by the step cut at top
 
Last edited:
I hear ya, no idea what the MLB is going to do for bats in the future.
I also heard on the news a few weeks ago the damage to trees the spotted lantern fly does to is not as harmful to the tree as first thought and wont cause the trees to die.
We are dealing with lantern flies up here in northeast... and Emerald Ash borer
 
Snap cut.

Instead of putting a box in the stick (Heavy wood) then back cut and letting it fall, I like a more controlled snap cut.

I set my 2-3 sets of rigging (pulleys or ring slings) pull rigging rope through, throw a qwik hitch in, and start the face cut. About half -3/4 through stop, then set the rigging rope- as pictured. To make certain the ground- rope guy knows I am ready, when i see the rig rope wiggling I will then make sure no crew- homeowner- ect is underneath or around where debris could possibly fly.

Give the rope guy my nod and make a back cut about halfway +/- through , just above the first cut. Now I can reposition the bucket back up, cause I have a controlled cut, I can take bigger pieces per rigging values.....

The cut stick stays- I look at the rope guy- nod, he nods back and I push pull on the stick and it snaps where I made the cuts, and I can lead the direction of the fall.
like I sad to @skwerl when he explained it , thats a lot to take in ,but I think I understand a little bit how it works after reading both of your posts
 
Back
Top