Breaking up at high rpm, carb issues, and converter issues.

I finally got the car fired up with the new ignition box. Only ran it for about 45 seconds, but AFR was bouncing between 18-20:1. With the old box it would go right to 14.7-15:1 since getting the new wideband. I will run it some more when my work day is over, but my hunch is that I'm going to have to put some jet back in it.
I have a feeling that the old ignition was worse than you thought.
 
I finally got the car fired up with the new ignition box. Only ran it for about 45 seconds, but AFR was bouncing between 18-20:1. With the old box it would go right to 14.7-15:1 since getting the new wideband. I will run it some more when my work day is over, but my hunch is that I'm going to have to put some jet back in it.


I’d put it back to where BLP had it.

Probably be a little fat but will be safe. Tune it from there. Might have to open up the IAB some if it stays lean @ idle.
 
Oh, and I put new plugs in it last night and gapped them @ .040". With the old box I was gapping them at .032" because I figured it was old and didn't have as much spark energy.

Even when new the Mallory had a voltage output to the coil of 525v and spark output (millijoules) of 135mj. The MSD has 570v and 160mj, so I figured that I could open the gap a little.

ooh-just freakin great…now your gonna run a second faster… & still say “you got a power adder“…”I need a spoT”…lolmf
 
Alright everyone,
I am embarrassed and excited to bring the news of what I found today. I was in so much disbelief that I took a picture. How could I make this stupid mistake? I swear, I’m smarter than this.

Well, enough blubbering, long story short, when I checked my timing today, I realized that after locking out my distributor (2nd trip to the track), my dumb ass set my timing at 24*, or honestly didn’t move it, but thought I set it at 34*.:facepalm:

I was using a 10* advance bushing, so I have my balancer marked at 24* with a yellow paint pen. I still don’t know how I did this because in my head I set it at 34*.

I’m hoping for big things this Friday. I set the carb back up where BLP had it, set timing at 28* (+4) and man does the throttle feel crisp when you crack it now. I’m excited to see what the converter is going to do now! I was so excited I called Mitch and then Darren, but Darren didn’t answer. ☹️😆

Planning to get a baseline and then bump timing 2* until mph goes down.

 
Congratulations and don't feel alone, I could write a book on the stupid shit that I've done over the years but the great thing about that is if you're not a fucking moron you won't ever do it again!

I don't know how I'm missing all these phone calls, guys say they're calling but It's evidently not pulling up on my screen, sorry dude!
 
Congratulations and don't feel alone, I could write a book on the stupid shit that I've done over the years but the great thing about that is if you're not a fucking moron you won't ever do it again!

I don't know how I'm missing all these phone calls, guys say they're calling but It's evidently not pulling up on my screen, sorry dude!

You know how you Heavy Hitters are, always ignoring the small people out there getting it done at the track every weekend.
 
Alright everyone,
I am embarrassed and excited to bring the news of what I found today. I was in so much disbelief that I took a picture. How could I make this stupid mistake? I swear, I’m smarter than this.

Well, enough blubbering, long story short, when I checked my timing today, I realized that after locking out my distributor (2nd trip to the track), my dumb ass set my timing at 24*, or honestly didn’t move it, but thought I set it at 34*.:facepalm:

I was using a 10* advance bushing, so I have my balancer marked at 24* with a yellow paint pen. I still don’t know how I did this because in my head I set it at 34*.

I’m hoping for big things this Friday. I set the carb back up where BLP had it, set timing at 28* (+4) and man does the throttle feel crisp when you crack it now. I’m excited to see what the converter is going to do now! I was so excited I called Mitch and then Darren, but Darren didn’t answer. ☹😆

Planning to get a baseline and then bump timing 2* until mph goes down.

Could that also be the engine temp problem as well? Doesn’t shit run hot with retarded timing? Or am I retarded?
 
What a sewing circle this has become…


ooh wait… it hasn’t been a week…
 
Could that also be the engine temp problem as well? Doesn’t shit run hot with retarded timing? Or am I retarded?
Temps were around 150 on the pass and would get up to 210 on the return road. 😬 Cool down to 180 pretty quick once in the pits. I leave the fan and water pump on for a few minutes to cool down.
 
Could that also be the engine temp problem as well? Doesn’t shit run hot with retarded timing? Or am I retarded?
yes, its still burning fuel in the exhaust so the head gets hot as fuck
that also could explain the very rich o2 readings, The o2 was seeing all the fuel still in the exhaust
when we first got efi, that big throttle body is a motherfucker to deal with
so we would put 0 at say 1800 rpm to try to limit idle speed
and take timing out again to limit idle speed with the throttle body cracked open
the thing would send water temp high as fuck at idle, and would get the headers almost glowing...lol
 
yes, its still burning fuel in the exhaust so the head gets hot as fuck
that also could explain the very rich o2 readings, The o2 was seeing all the fuel still in the exhaust
when we first got efi, that big throttle body is a motherfucker to deal with
so we would put 0 at say 1800 rpm to try to limit idle speed
and take timing out again to limit idle speed with the throttle body cracked open
the thing would send water temp high as fuck at idle, and would get the headers almost glowing...lol
Are you saying your couldn't .... or weren't allowed to .... fit the butterflies to the throttle bores? That's nuts.
 
I lost track of what head is on this Ford. Some heads for Fords have really good fast burn chambers, so even though 24 is not likely enough it isn't as far retarded as you might think, compared to the 23 deg. SBC everybody seems to think sets the standard at 36. Some Fords and low valve angle SBC heads 18 & 15 deg. only need 26 to make the best HP.
 
Last edited:
Are you saying your couldn't .... or weren't allowed to .... fit the butterflies to the throttle bores? That's nuts.
butterfly
one giant oval butterfly 7" x 4.5" oval
it had so much manifold vacuum on it at idle you couldnt feather into the throttle, you would push with your foot and nothing. push a little harder, nothing. push a little harder and it breaks the vacuum and snaps open
then youd try to lift a little and vac would slam it shut
its still a fuckstory 7 years later.
people have made all kinds of linkage trying to get leverage on it earlier

 
If the throttle shaft is large enough and strong enough it doesn't flex, and the blade is not offset so much it gives it too strong a closing force, I guarantee it can be made to seal to minimum near zero air flow and be made to open gradually. Is the throttle shaft on ball bearings, like a Weber carb? If it isn't, it should be.

Have you studied the throttle linkage bell crank on the throttle body on a 2004-2006 GT-40? that has a throttle cable bell crank.

Nearly every Cobra kit car has throttle linkage from hell that makes them near impossible to drive in the rain because the carb comes off idle way to quick. The well worn video of the gal pulling out of a car show into the street in her boyfriend's Cobra and the car going crazy fishtailing and running into a pole and (was it ?) a Honda car a block down the street is an example.

I've made a asphalt circle track car more than a half-second faster on a 1/2 mile touching nothing but the throttle linkage, just fixing the bell crank arrangement so the driver had throttle control that wasn't just like an on/off switch.
 
Back
Top