Breaking up at high rpm, carb issues, and converter issues.

While some of you were in here running your soup coolers, I was trying to get shit done. 😆

Tomorrow I’ll make a coil bracket and tie up a few loose ends. I cleaned up a lot of wiring that I wasn’t happy with. Still not 100% satisfied with some of it, but it’s getting there.

 
What are those square clips called that have ziptie through them ive been using the Christmas tree zip ties and don't like the look
 
What are those square clips called that have ziptie through them ive been using the Christmas tree zip ties and don't like the look
I don’t know the name, but they have them at home dumpo. Or you can order from McMaster Carr.
 
What are those square clips called that have ziptie through them ive been using the Christmas tree zip ties and don't like the look
Tie wrap bases or cable tie mount bases, Google either of those search terms.
 
GTSE 100 Pack Of Black Screw Mounts, Zip Ties Up To 0.2" Wide, Saddle Type Zip Tie Anchors https://a.co/d/cJT6Fyz

Those are the screw mounted ones. Use them anywhere outside the cabin of the car, as the adhesive backed ones don't take a lot of abuse before detaching themselves, especially when exposed to the elements.
 
Positive junction stud is loose.
Good eye! That’s why I say I had to tie up a few loose ends. I have that, the magnetic pick up wires, make a coil bracket, terminate coil wires at the coil, install new battery when it arrives, do an oil change, and more test n tune Friday.
 
Good eye! That’s why I say I had to tie up a few loose ends. I have that, the magnetic pick up wires, make a coil bracket, terminate coil wires at the coil, install new battery when it arrives, do an oil change, and more test n tune Friday.
I know you were saying that, that's why I pointed it out just to fuck with ya. 😁
 
I just couldn't help myself. I'll have it on stand-by.



Dang! Just saw this post.......I have a big box full of chips from 3000-9000rpm, and I no longer have a use for them. Wish I would have known you needed some.
 
Dang! Just saw this post.......I have a big box full of chips from 3000-9000rpm, and I no longer have a use for them. Wish I would have known you needed some.
Me too! Lol It’s weird how these kits skip around. I guess 100 rpm in the big picture might not mean much? For example, the 4K kit goes up to 4800, but the 5k kit starts at 5100.

I’ve been launching at 5000, so I guess I’ll pick either 4800 or 5100 to start.

I have the 4800 in there now.
 
Me too! Lol It’s weird how these kits skip around. I guess 100 rpm in the big picture might not mean much? For example, the 4K kit goes up to 4800, but the 5k kit starts at 5100.

I’ve been launching at 5000, so I guess I’ll pick either 4800 or 5100 to start.

I have the 4800 in there now.

I will grab that box tomorrow and see what I have in that range.
 
Dang! Just saw this post.......I have a big box full of chips from 3000-9000rpm, and I no longer have a use for them. Wish I would have known you needed some.
Corn chips or Potato chips? asking for a friend.
 
I finally got the car fired up with the new ignition box. Only ran it for about 45 seconds, but AFR was bouncing between 18-20:1. With the old box it would go right to 14.7-15:1 since getting the new wideband. I will run it some more when my work day is over, but my hunch is that I'm going to have to put some jet back in it.
 
Oh, and I put new plugs in it last night and gapped them @ .040". With the old box I was gapping them at .032" because I figured it was old and didn't have as much spark energy.

Even when new the Mallory had a voltage output to the coil of 525v and spark output (millijoules) of 135mj. The MSD has 570v and 160mj, so I figured that I could open the gap a little.
 
Back
Top