Breaking up at high rpm, carb issues, and converter issues.

Bad tachs, bad rpm chips, bad ignition switches are some things that I’ve found after spending $8,000 trying to fix a high rpm flutter.

I hate chasing that kinda stuff.


Mitch developed a really bad bog when the tires hit… almost shut off then started bucking real bad till downtrack then haul ass. Chased it for weeks & spent a ton of $$. No fix. He showed up at the door car shootout with the issue & there were a LOT of badasses working on it for days & we tried stuff that was really off the wall & never did find it.

I think I might have maybe found it while shaking the car down @ the YB Nats… bad Ferd style solenoid that pulled the power stud out when I tugged on the nut holding the power cable on.

Stupid shit you never would suspect is sometimes the issue.

That was the craziest thing I ever had to deal with. Don't even want to add up all the new parts that were thrown at that mess for nothing. Ended up being the ONLY electrical component that nobody mentioned, so was not replaced until you found it at Cecil. A $28 part fixed it. I still have a spare in my trailer.

BTW, I blame that failure on goneracin.......he put too much torque in my motor.:lmao:
 
That was the craziest thing I ever had to deal with. Don't even want to add up all the new parts that were thrown at that mess for nothing. Ended up being the ONLY electrical component that nobody mentioned, so was not replaced until you found it at Cecil. A $28 part fixed it. I still have a spare in my trailer.

BTW, I blame that failure on goneracin.......he put too much torque in my motor.:lmao:


That was definitely a weird deal. Fukn Bob. 😄


Try this for the Vertigo. I had it a coupla years ago & this fixed it. It took about 2 weeks.
https://www.hopkinsmedicine.org/health/treatment-tests-and-therapies/home-epley-maneuver
 
According to VP.......C12 has won more motorsports competitions than ALL of their other fuels combined. IMO, it is the ONLY fuel I would run in your combo.
Wow, I was planning to switch when Bob and Darren mentioned it, but after you said what you said, I looked it up. According to VP, the VP110 is good up to 12:1 compression. This engine before the fly cutting of the pistons was spec’d at 13.4:1.

C12 says it’s good up to 15:1.

 
Wow, I was planning to switch when Bob and Darren mentioned it, but after you said what you said, I looked it up. According to VP, the VP110 is good up to 12:1 compression. This engine before the fly cutting of the pistons was spec’d at 13.4:1.

C12 says it’s good up to 15:1.



Before I switched to alky, I was running VP113. Stinky nasty & expensive stuff but it takes 6 jets up over anything else & made good power in the weedeater. Very consistent too.
 
BLP just called me and they can't wrap their head around the jets going so low, yet being so rich. They are thinking if it's an ignition issue, it's causing it to run rich. They are going to give me some extra jets and power valves to try. These guys have been great. Carb is shipping back today and I should have it tomorrow. As long as I get it tomorrow, I will be back out testing Friday night.

They also think the NGK-7's are fine, but I know some others have said that they are on the hot side for my motor.
 
I think the sevens will be fine I would either run sevens or eights in that motor. I'm definitely thinking it is ignition/box related.
 
I just couldn't help myself. I'll have it on stand-by.




I have 7AL2… not a +…that I bought from Bangr, fresh from MSD with paperwork that has been sitting in the box since I got it. Spare that I will never use. PM me if you want to save some $$. I’ll guarantee it. No workee I’ll send your $$ back & beat Bangr’s…. Well skip that last part. 😄
 
I have 7AL2… not a +…that I bought from Bangr, fresh from MSD with paperwork that has been sitting in the box since I got it. Spare that I will never use. PM me if you want to save some $$. I’ll guarantee it. No workee I’ll send your $$ back & beat Bangr’s…. Well skip that last part. 😄

Sent you a PM on this if @Patriot Racer is not interested.
 
Feel better Mitch. Hope everything clears up real soon.
Pat, I’ve used strictly C12 since day 1. A Book 4150 carb with 13.9 to 1 big block.
My engine builder said run A5671-9, I’ve used both 7 and 8.
Said don’t drive around on 9s, they are a race plug strictly to him. My car is far from optimized. But it works. And heavy as fugg.
 
My new fluke meter just got delivered, so I ran out and ohm’s out my coil and spark plug wires.

Primary coil - .500
Secondary coil reading - 12.28K ohms

Basically perfect.

 
Plug wires all ohm’d out within spec, but I just do not get a warm fuzzy with these fire core wires that they are fully seated on the plug. I feel a definitive snap on top of the distributor, but big questions when putting it on a plug. The silicone portion is tight, but the only way I know it’s on is if I forcefully push toward the plug and wiggle it to feel the metal to metal contact. Never hear or feel them snap.
 
What I found on those wires was the same thing on my turbo Camaro, I would get them on there and they didn't feel right and I never thought that they were fully home. I would get them pushed down as far as I could and work my thumb around on there and honestly I would take a pair of pliers and crimp on the outside of the boot to kind of squeeze it in.
 
That was definitely a weird deal. Fukn Bob. 😄


Try this for the Vertigo. I had it a coupla years ago & this fixed it. It took about 2 weeks.
https://www.hopkinsmedicine.org/health/treatment-tests-and-therapies/home-epley-maneuver
Several years ago I had a really long surgery, I was on the table for a bit over 15 hours.
When I came out I had vertigo so damn bad I could barely move without puking, and that sucked since they had just cut me in half like a fish!
Couldn't give me any of the typical drugs for vertigo since I had an NG tube.
After suffering for a few days I said why don't you take those pills, crush them up, and stick them in an IV.
They tried that epley move but because of my surgery they couldn't do much with me at that time.
A doctor finally said "IF" you want to try something WAIT until I am out of the room and do this with your wife present in case something goes wrong. He said I "found" this info on a Google search............. ;) As in he didn't want to be the one that recommended doing this......
Hit myself in the side of my head as hard as I could tolerate to get stuff back where it belongs.
Well, it fucking worked!
Slight headache, I always fucking over-do things, but that vertigo was nearly impossible to deal with.
 
Plug wires all ohm’d out within spec, but I just do not get a warm fuzzy with these fire core wires that they are fully seated on the plug. I feel a definitive snap on top of the distributor, but big questions when putting it on a plug. The silicone portion is tight, but the only way I know it’s on is if I forcefully push toward the plug and wiggle it to feel the metal to metal contact. Never hear or feel them snap.
Did you wiggle and bend the hell out of the ends, especially the spark plug end, while measuring?
My first set of Firecore wires clicked nice on both ends.
The second set for our other car don't all click on the spark plug end.
Not sure what changed, but the wires work fine.
 
Back
Top