Breaking up at high rpm, carb issues, and converter issues.

With a battery in the trunk you need a dedicated ground cable from the battery to the engine and electronics. You cannot ground it through the chassis, it must have 00 or prefrerbly 0000 cable.
I have 00 welding cable from the battery to the engine block.
 
ive tuned at a very high level using o2's i use my otoscope a lot said:
“””see if my wideband tells me what the plugs show me.””” <the point was to evaluate the plug vs the data from the wide-band for comparison/diagnose the issues.

My wide and data did not match the plugs down at SGMP/Georgia running RVW, or running up here at Byron or GLD. We have since changed type & brand sensors to have better data.
I’m not saying his data is bad or that your a novice tuner, just that the plugs need to be seen for reference.
When I “test & tune” at Byron, I pull around the corner at the end, roll on the grass out of the way pick up my chutes & pull / change the plugs. Then I drive back to my pit, pull the data, & compare/ make changes. I do the same at GLD. If I drive back to the pits, the plugs tell me nothing.
 
you sure the breaking up at high RPM is a carb issue and not an electrical issue

EDIT, I just read the OP and commented. I did not realize electrical has been mentioned a few times and the thread was 4 pages.
 
Last edited:
First off thanks to everybody for the help and suggestions. Here is my plan of attack, already in progress:

Carb is off, packed, and will ship back to BLP tomorrow, so they can have a look.

I ordered a shielded MSD pick up wire. I also removed my alternator wire and I’m going to run it under the car as Darren suggested. The new pick up wires will go through their own hole in the firewall.

Once the wiring gets squared away and I get the carb back I will get back out there for testing. If the car breaks up at high RPM, I have some Moroso sleeved spark plug wires on the way that I will swap. If it still breaks up with the Moroso wires, this Mallory will go in the shit can (4 sale) and I will buy the MSD 7AL2-plus box. I have no need for the grid system. I pretty much need a 2 step and a rev limiter, that’s it.
 
First off thanks to everybody for the help and suggestions. Here is my plan of attack, already in progress:

Carb is off, packed, and will ship back to BLP tomorrow, so they can have a look.

I ordered a shielded MSD pick up wire. I also removed my alternator wire and I’m going to run it under the car as Darren suggested. The new pick up wires will go through their own hole in the firewall.

Once the wiring gets squared away and I get the carb back I will get back out there for testing. If the car breaks up at high RPM, I have some Moroso sleeved spark plug wires on the way that I will swap. If it still breaks up with the Moroso wires, this Mallory will go in the shit can (4 sale) and I will buy the MSD 7AL2-plus box. I have no need for the grid system. I pretty much need a 2 step and a rev limiter, that’s it.
AL2 is a good box. I may have a loaner at madcap, let me see on tuesday
al3 we all had issues with in PS, it was a POS...lol
 
The 7-AL3 has many issues...........

I suspect plug wires or electrical.

When I wire cars I use a Ford Starter Relay under the hood, I don't like a hot battery cable on the starter close to headers all the time.
I use a 4 pole Battery Disconnect Switch.
Most of my builds have been EFI so it makes things easy for me.
The large set of terminals on the switch are for the positive cable.
The small set are to kill the electric fuel pump in the rear. Actually just kills power to the relay for the fuel pump, next to no current going through the switch for that.

The alternator gets wired to the starter relay up front. No need to worry about the alternator keeping the engine running when the switch is thrown, once the fuel pump on an EFI car is off, the engine is off.

On a carb application that second set of contacts can be used to kill the engine via the MSD or similar.
Ground the white points input wire and the MSD unit can not fire.
Or kill the +12v switched thin red wire for the MSD and it will be off.

Many ways to skin the cat.
 
Taylors are junk, as far as quality of conductor goes.
that was my experience with the firecore. A customer got them for free for an outlaw 632 deal. I didnt like them at all, but they didnt missfire
Check rotor phasing to make sure its phased.
I have seen the screws that hold the rotor together loosen as well, especially the 2 piece rotor with the base and top. The screw that holds the base on is a pain in the ass. not sure which rotor that uses

I guess I have to cut a hole in a brand new MSD billet distributor cap to check it. I don't have an adjustable rotor at the moment. I wish I had a spare cap.

MSD Ignition 84313 MSD Replacement Distributor Caps | Summit Racing
 
Last edited:
I think MSD caps are Ford caps. I think you can buy a cheap cap for a Ford at local parts store to drill a hole in
I don't know if this billet msd uses one that is specific to this distributor. This is a smaller profile cap. Let me search that up.
 
I don't know if this billet msd uses one that is specific to this distributor. This is a smaller profile cap. Let me search that up.
I am pretty sure my BBC billet MSD distributor uses a Ford cap.
It has the "tits"sticking up on the cap for the plug wires (like a Ford) not the holes in the cap that the plug wires push into like on a GM/Chevy. So I figured it was a Ford style cap on my MSD
Being that yours is a small profile cap it might be different.
 
I sent the carb back to BLP 1 day air. Cost me $140, but I wanted to get it back asap, so I can get back to the track. They received it this morning and slapped it on their 670HP motor.

They will be running it to see what they find. I will post if I hear from them, but they sent me this already.

 
I guess the issue is definitely with my car and not the carb. It sounds killer on their shop motor.


Start up

Running
 
It is a lot easier to blame the carb than diagnose an ignition problem.
 
It is a lot easier to blame the carb than diagnose an ignition problem.
I was planning to ohm out all of my plug wires today and check the readings on the coil, but my 20 year old craftsman multimeter took a crap a few days ago. Ordered a fluke and it was supposed to be here today, but of course it’s not coming until tomorrow.

I routed my alternator wire under the car last night and my shielded mag pick up wires will be here tomorrow.
 
Dumb question, but did you try a new set of spark plugs? My car at the track a couple of years ago had a high speed miss with which I found was new spark plugs, found it on the 2nd to last pass. Put in the old ones and BAM right back to 7400rpm sounding like a smooth machine. Pretty surprised by that one, but it was nice when O'rileys took them back and gave me a refund.
 
Back
Top