Breaking up at high rpm, carb issues, and converter issues.

And, keep the faith!
You'll get there.
I went through some struggles with my car when I did a brand new combo.
New engine, trans, and rear.......
Took two weeks but got it right.

Chassis dynos are so much better to figure shit out on than the track.
engine dynos even better
breaks it down to its simplest form
i try to run customers coil, crank trigger etc.
If its fine on my dyno, your car is fucked.
Then find a chassis dyno
 
.012 is not 12 jets, its 12 thou so roughly 3-4 jets
.025 is fine. i ran 1500 hp na to 11,500 at .025...lol
throw that box away
the signal wires should NEVER be near noisy shit, like an alternator wire
fuck, take the alt belt off if you can for a pass?
i use moroso, msd or lately Scott customs, which imo are the best wire on the planet

ive tuned at a very high level using o2's
i use my otoscope a lot, but ive sent shit that went in the 3's in the 1/8th using o2 data
but maybe im wrong...lol
Chance is better than even you had the O2 sensor(s) installed in the proper location(s) so your numbers are meaningful. If I read one of his posts correctly, OP's O2 sensor is within inches of the open header collector, so his A/F numbers are junk and near worthless.

I asked OP for venturi and throttle bore size but he only posted a build sheet that shows cfm, no throat dimensions. I asked around and find it is "probably a 1.5" or 1.5625" venturi with 1.75 throttle bore, in which case the original jetting was very close and he has some other thing influencing this 4rd order phustercluck, hood scoop interference or the fan is blowing over the bowl vents and causing the mixture to be fubar.

The sound of the misfire in the videos sounds like a carb with 15 sizes too small a main jet.

The power valve has no effect on idle mixture unless the diaphragm is leaking or it is hitting the screw boss in the body of a die-cast zinc Holley and this is highly unlikely in a BLP billet carb.
 
Chance is better than even you had the O2 sensor(s) installed in the proper location(s) so your numbers are meaningful. If I read one of his posts correctly, OP's O2 sensor is within inches of the open header collector, so his A/F numbers are junk and near worthless.

I asked OP for venturi and throttle bore size but he only posted a build sheet that shows cfm, no throat dimensions. I asked around and find it is "probably a 1.5" or 1.5625" venturi with 1.75 throttle bore, in which case the original jetting was very close and he has some other thing influencing this 4rd order phustercluck, hood scoop interference or the fan is blowing over the bowl vents and causing the mixture to be fubar.

The sound of the misfire in the videos sounds like a carb with 15 sizes too small a main jet.

The power valve has no effect on idle mixture unless the diaphragm is leaking or it is hitting the screw boss in the body of a die-cast zinc Holley and this is highly unlikely in a BLP billet carb.
even me?
i can hear you...lol
if hes close to the end of the collector, at WOT its moving enough air to not be too bad
and yes, im in the primaries about 10" from the head
 
even me?
i can hear you...lol
if hes close to the end of the collector, at WOT its moving enough air to not be too bad
and yes, im in the primaries about 10" from the head
even you what?
 
So AFR is fubar, 12 jets are not 12 jets, it’s 15 jets too lean, but popped the same with 12 jets that aren’t really 12 jets higher than it was before. 😂

Tomorrow I’m unloading the car, removing the carb and sending back to BLP for a look. I bought a shielded pick-up wire and I’m going to reroute it away from everything else. I’m also going to ground ignition directly to the battery.

Once I get the carb back, I’ll go out and test it again. Oh, @Mike Beck I also ordered some NGK 8’s. I’m using VP110, which has a slightly higher octane rating than Sunoco 110.
 
At full throttle going down the track if the wideband sensor is at least 4 inches from the end of the collector it will give meaningful data, but only at full-song.
 
So AFR is fubar, 12 jets are not 12 jets, it’s 15 jets too lean, but popped the same with 12 jets that aren’t really 12 jets higher than it was before. 😂

Tomorrow I’m unloading the car, removing the carb and sending back to BLP for a look. I bought a shielded pick-up wire and I’m going to reroute it away from everything else. I’m also going to ground ignition directly to the battery.

Once I get the carb back, I’ll go out and test it again. Oh, @Mike Beck I also ordered some NGK 8’s. I’m using VP110, which has a slightly higher octane rating than Sunoco 110.
at 13-1 id probably go with c12 VP
esp at lower elevations
that isnt your issue, but its a better choice imo
 
any chance the trigger wires between the magnetic pick and the cd box are reversed ?

As already mentioned, if the trigger wires are anywhere near primary or secondary coil wires ...... (n)
 
Last edited:
any chance the trigger wires between the magnetic pick and the cd box are reversed ?
No, but I’m learning this isn’t what you want. Red is the alternator wire and the one right above it the goes up and right is my pick up wires. It was never an issue with my 331, but I was only spinning it to 6000. If I short shift this motor at 6000 m, it doesn’t break up. It actually ran its fastest pass (6.06) in the hottest part of the day when I accidentally short shifted at like 6200.

 
Is your battery in the trunk? If so run that alternator wire underneath the car.
 
avgas runs cleaner than all of them, add MMT to it and the octane is higher too

but ....... nevermind
 
Back
Top