Big Bore 427w

Ok, I’m blaming @Mark O'Neal for this. I didn’t even know what PRI was until last week when I asked him. I decided to make the trip and of course I was like a kid in a candy store.

When I passed by the Jones Racing booth/display, I was blown away by the looks and quality of their stuff. I was never quite happy with my pulley configuration and alternator bracket. I was always having alignment issues and tore up a couple belts.

I bought all new HTD pulleys, crankshaft mandrel, and alternator bracket that will mount lower than previously.

 
Last edited:
I also bought a Jones Racing fuel log, but it was hitting the secondary linkage. I had to buy a couple fitting to extend the tubes further away. Not sure I like it, might be too far away now?

 
I also bought a Jones Racing fuel log, but it was hitting the secondary linkage. I had to buy a couple fitting to extend the tubes further away. Not sure I like it, might be too far away now?

are your float bowls on backwards?
 
Ok, I’m blaming Mark for this. I didn’t even know what PRI was until last week when I asked him. I decided to make the trip and of course I was like a kid in a candy store.

When I passed by the Jones Racing booth/display, I was blown away by the looks and quality of their stuff. I was never quite happy with my pulley configuration and alternator bracket. I was always having alignment issues and tore up a couple belts.

I bought all new HTD pulleys, crankshaft mandrel, and alternator bracket that will mount lower than previously.

is it Mark 0'Neal's fault you couldn't line up your belts?
 
They did, but my job to look closer. I would have figured it out when I went to hook up throttle linkage lol

Thanks.
You didn't hear it from me, but that ain't all the por systains blessings you're going to have to deal with. Better get a wide band O2 gauge.

Before you use that thing, do you have the means to measure the width and length of the transition slots? Many of the cnyna billet bases are fubar, slots too wide.
 
You didn't hear it from me, but that ain't all the por systains blessings you're going to have to deal with. Better get a wide band O2 gauge.

Before you use that thing, do you have the means to measure the width and length of the transition slots? Many of the cnyna billet bases are fubar, slots too wide.
Yes, I have a wideband. I can measure the slots, but have no idea what they are supposed to be. You have a reference?
 
Yes, I have a wideband. I can measure the slots, but have no idea what they are supposed to be. You have a reference?

The old school 1&11/16" and 1&3/4" Holleys, that by some strange coincidence nearly always run good, have slots .025" wide by .180" to .200" long. Wider than .026" will likely make a carb difficult to tune around a too rich A/F at some throttle position near level road load.

Playing with idle jet and idle air bleed can get it right on one throttle position but a slight change in throttle can change the A/F too much. Sometimes, but not always, this can be cured by adding a T-slot jet in the body to restrict the passage to the slot.

The reason a wide and long is a problem is because slot area above the butterfly is air bleed in to the idle/transition circuit, below the butterfly is obviously mixed fuel and air discharge. As the butterfly goes up the slot it cuts off air bleed and increases fuel feed.

When the slot is too wide and too long, too much air bleed (= lean) turns to too much fuel feed (= rich), so moving the throttle changes the A/F too much and in the wrong direction.

Ideally, the A/F progresses leaner from rich (12-13/1) curb idle to an economical lean (15-16/1) cruise A/F on the main jet and then, when the power valve opens, to rich (12.5/1) for best power WOT.

More often than not, the light load misfire people complain about is from too rich, but they think it is too lean because the rich misfire passes unburned oxygen and fools the O2 sensor to show a lean number.
 
Itey is ahead of the game…..I was gonna suggest before you put fuel in it to take it apart and verify it has what the build sheet says it has. 😉 I hope it works great for ya, it looks purdy!
 
Well my Ron Davis radiator finally showed up this morning. It’s a very nice piece. Did some quick mock up and brainstormed on mount brackets. I have some ideas. It’s supposed to be warm the next 3-4 days, so hopefully I can spend some time in the garage.

 
If you don't use the entire mounting kit you can share the leftovers with 89 Fox 351.

iu
 
If you don't use the entire mounting kit you can share the leftovers with 89 Fox 351.

iu
I have those on hand, but I prefer the rigid mounting style that you guys referred to in the other thread. 😉
 
Bought myself a carb stand and it arrived today. I put my carb on it and changed the primary Holley jets out for my new BLP’s. Once I was done my eyes were drawn to a crack in the main body in one of the primary side air bleed bosses. :facepalm:

 
Back
Top